A model of the deformation of 12Kh18N9 steel used in fuel assemblies is verified based on the results of experimental investigations. The characteristics of the investigated steel under dynamic loading are determined by the Kolsky method using Nicholas scheme. The values of the ultimate strength and their dependence on the strain rate and temperature are found based on the actual strain diagrams obtained under different loading conditions. The parameters of the Johnson–Cook model were determined from the experimental results on deformation of 12Kh18N9 steel under static and dynamic loading. The verification process showed that the selected mathematical model gives a very accurate description of the behavior of the material under dynamic loading conditions.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
O. Yu. Vilenskii, D. A. Lapshin, and E. G. Novinskii, “Computational analysis and assessment of the consequences of the fall of fuel assemblies using verified models of deformation of structural materials,” At. Energiya, 131, No. 5, 295 (2021).
G. Kolsky, “Investigation of the mechanical properties of materials at high loading rates,” Mekhanika, No. 4, 108–119 (1950).
A. M. Bragov and A. K. Lomunov, “Aspects of constructing strain diagrams by Kolsky method,” in: Applied Problems of Strength and Plasticity. Statics and Dynamics of Deformable Systems, Gor’kii (1984), pp. 125–137.
A. M. Bragov and A. K. Lomunov, “Methodological aspects of studying dynamic material properties using the Kolsky method,” Int. Impact Eng., No. 16(2), 321–330 (1995).
T. Nicholas, “Tensile testing of materials at high rates of strain,” Exp. Mech. 21, No. 5, 177–195 (1981).
A. M. Bragov, Experimental Analysis of Deformation and Fracture of Materials at Strain Rates 102–105 sec–1: Doctoral Dissertation in Technical Sciences, Lobachevskii NNSU, Nizhny Novgorod (1998).
G. Johnson and W. A. Cook, “Constitutive model and data for metals subjected to large strains, high strain rates, and high temperatures,” in: Proc. 7th Int. Symp. on Ballistic, Netherlands (1983), pp. 541–547.
A. Yu. Konstantinov, Experimental and Computational Investigation of the Behavior of Structural Materials under the Action of Dynamic Loads: Candidate Dissertation in Technical Sciences, Nizhny Novgorod (2007).
V. L. Kotov, A. Yu. Konstantinov, and Yu. I. Kibets, “Numerical modeling of plane-parallel motion of conical hammers in an elastoplastic medium,” Probl. Prochn. Plastichn., 75, No. 4, 303–311 (2013).
D. A. Lapshin, Computational-Experimental Analysis of the Strength of Intra-Object Transport Containers of BN Type Reactors in Accidents with a Fall: Candidate’s Dissertation in Technical Sciences, Lobachevsky NNSU, Nizhny Novgorod (2015).
T. Rodriguez, C. Navarro, and V. Sanchez-Galvez, “Splitting tests: an alternative to determine the dynamic tensile strength of ceramic materials,” Physique IV (1994), pp. 101–106.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Atomnaya Énergiya, Vol. 132, No. 6, pp. 342–346, June, 2022.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Vilenskii, O.Y., Lapshin, D.A., Ryabtsov, A.V. et al. Verification of a Mathematical Model of 12Kh18N9 Steel Deformation Under Dynamic Loading of Fuel Assemblies. At Energy 132, 359–363 (2022). https://doi.org/10.1007/s10512-023-00960-1
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10512-023-00960-1