Skip to main content
SpringerLink
Log in

Effect of dispersed phase viscosity on maximum droplet generation frequency in microchannel emulsification using asymmetric straight-through channels

  • Original Paper
  • Published:
Microfluidics and Nanofluidics Aims and scope Submit manuscript

Abstract

Uniformly sized droplets of soybean oil, MCT (medium-chain fatty acid triglyceride) oil and n-tetradecane with a Sauter mean diameter of d 3,2 = 26–35 μm and a distribution span of 0.21–0.25 have been produced at high throughputs using a 24 × 24 mm silicon microchannel plate consisting of 23,348 asymmetric channels fabricated by photolithography and deep reactive ion etching. Each channel consisted of a 10-μm diameter straight-through micro-hole with a length of 70 μm and a 50 × 10 μm micro-slot with a depth of 30 μm at the outlet of each channel. The maximum dispersed phase flux for monodisperse emulsion generation increased with decreasing dispersed phase viscosity and ranged from over 120 L m−2 h−1 for soybean oil to 2,700 L m−2 h−1 for n-tetradecane. The droplet generation frequency showed significant channel to channel variations and increased with decreasing viscosity of the dispersed phase. For n-tetradecane, the maximum mean droplet generation frequency was 250 Hz per single active channel, corresponding to the overall throughput in the device of 3.2 million droplets per second. The proportion of active channels at high throughputs approached 100% for soybean oil and MCT oil, and 50% for n-tetradecane. The agreement between the experimental and CFD (Computational Fluid Dynamics) results was excellent for soybean oil and the poorest for n-tetradecane.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
$34.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or eBook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12

Similar content being viewed by others

Abbreviations

A m :

Active cross-sectional area of microchannel plate (m2)

Ca :

Capillary number

d :

Droplet diameter (m)

d10, d50, d90:

Droplet diameters corresponding to 10, 50, and 90% cumulative undersize mass (m)

d 3,2 :

Sauter mean diameter of droplets (m)

d ch :

Diameter of microchannel (m)

k :

Fraction of active microchannels

h :

Height of gap between microchannel plate and cover slip (m)

N 0 :

Total number of microchannels in plate

Q :

Volume flow rate (m3 s−1)

U :

Velocity of disperse phase in microchannel (m s−1)

\( \bar{U} \) :

Mean velocity of disperse phase in active microchannels (m s−1)

W :

Width of gap between MC plate and cover slip (m)

We :

Weber number

γ :

Interfacial tension (N m−1)

η :

Viscosity (Pa s)

ρ :

Density (kg m−3)

τ :

Shear stress (Pa)

c:

Continuous phase

cr:

Critical conditions

d:

Disperse phase

References

  • Abate AR, Weitz DA (2009) High-order multiple emulsions formed in poly(dimethylsiloxane) microfluidics. Small 18:2030–2032

    Article  Google Scholar 

  • Abrahamse AJ, van Lierop R, van der Sman RGM, van der Padt A, Boom RM (2002) Analysis of droplet formation and interactions during cross-flow membrane emulsification. J Membr Sci 204:125–137

    Article  Google Scholar 

  • Anna SL, Bontoux N, Stone HA (2003) Formation of dispersions using ‘flow-focusing’ in microchannels. Appl Phys Lett 82:364–366

    Article  Google Scholar 

  • Egidi E, Gasparini G, Holdich RG, Vladisavljević GT, Kosvintsev SR (2008) Membrane emulsification using membranes of regular pore spacing: droplet size and uniformity in the presence of surface shear. J Membr Sci 323:414–420

    Article  Google Scholar 

  • Holdich RG, Dragosavac MM, Vladisavljević GT, Kosvintsev SR (2010) Membrane emulsification with oscillating and stationary membranes. Ind Eng Chem Res 49:3810–3817

    Article  Google Scholar 

  • Kawakatsu T, Kikuchi Y, Nakajima M (1997) Regular-sized cell creation in microchannel emulsification by visual microprocessing method. J Am Oil Chem Soc 74:317–321

    Article  Google Scholar 

  • Kikuchi Y, Sate K, Ohki H, Kaneko T (1992) Optically accessible microchannels formed in a single-crystal silicon substrate for studies of blood rheology. Microvasc Res 44:226–240

    Article  Google Scholar 

  • Kobayashi I, Nakajima M, Chun K, Kikuchi Y, Fujita H (2002) Silicon array of elongated through-holes for monodisperse emulsion droplets. AIChE J 48:1639–1644

    Article  Google Scholar 

  • Kobayashi I, Nakajima M, Mukataka S (2003) Preparation characteristics of oil-in-water emulsions using differently charged surfactants in straight-through microchannel emulsification. Colloids Surf A: Physicochem Eng Asp 229:33–41

    Article  Google Scholar 

  • Kobayashi I, Mukataka S, Nakajima M (2004) Effect of slot aspect ratio on droplet formation from silicon straight-through microchannels. J Colloid Interface Sci 279:277–280

    Article  Google Scholar 

  • Kobayashi I, Mukataka S, Nakajima M (2005a) Production of monodisperse oil-in-water emulsions using a large silicon straight-through microchannel plate. Ind Eng Chem Res 44:5852–5856

    Article  Google Scholar 

  • Kobayashi I, Mukataka S, Nakajima M (2005b) Novel asymmetric through-hole array microfabricated on a silicon plate for formulating monodisperse emulsions. Langmuir 21:7629–7632

    Article  Google Scholar 

  • Kobayashi I, Uemura K, Nakajima M (2007) Formulation of monodisperse emulsions using submicron-channel arrays. Colloids Surf A: Physicochem Eng Asp 296:285–289

    Article  Google Scholar 

  • Kobayashi I, Takayuki T, Maeda R, Wada Y, Uemura K, Nakajima M (2008a) Straight-through microchannel devices for generating monodisperse emulsion droplets several microns in size. Microfluid Nanofluid 4:167–177

    Article  Google Scholar 

  • Kobayashi I, Wada Y, Uemura K, Nakajima M (2008b) Generation of uniform drops via through-hole arrays micromachined in stainless-steel plates. Microfluid Nanofluid 5:677–687

    Google Scholar 

  • Kobayashi I, Wada Y, Uemura K, Nakajima M (2009) Production of monodisperse water-in-oil emulsions consisting of highly uniform droplets using asymmetric straight-through microchannel arrays. Microfluid Nanofluid 7:107–119

    Article  Google Scholar 

  • Kobayashi I, Wada Y, Uemura K, Nakajima M (2010) Microchannel emulsification for mass production of uniform fine droplets: integration of microchannel arrays on a chip. Microfluid Nanofluid 8:255–262

    Article  Google Scholar 

  • Link DR, Anna SL, Weitz DA, Stone HA (2004) Geometrically mediated breakup of drops in microfluidic devices. Phys Rev Lett 92:054503

    Article  Google Scholar 

  • McClements DJ (2004) Food emulsions: principles practices and techniques. CRC Press, Boca Raton

    Book  Google Scholar 

  • Nakashima T, Shimizu M, Kukizaki M (2000) Particle control of emulsion by membrane emulsification and its applications. Adv Drug Deliv Rev 45:47–56

    Article  Google Scholar 

  • Neves MA, Ribeiro HS, Butron Fujiu K, Kobayashi I, Nakajima M (2008) Formulation of controlled size PUFA-loaded oil-in-water emulsions by microchannel emulsification using β-carotene-rich palm oil. Ind Eng Chem Res 47:6405–6411

    Article  Google Scholar 

  • Nisisako T, Torii T (2006) Microfluidic large-scale integration on a chip for mass production of monodisperse droplets and particles. Lab Chip 8:287–293

    Article  Google Scholar 

  • Nisisako T, Torii T, Takahashi T, Takizawa Y (2006) Synthesis of monodisperse bicolored Janus particles with electrical anisotropy using a microfluidic co-flow system. Adv Mater 18:1152–1156

    Article  Google Scholar 

  • Steegmans ML, Schroën KGPH, Boom RM (2009) Characterization of emulsification at flat Y junctions. Langmuir 25:3396–3401

    Article  Google Scholar 

  • Sugiura S, Nakajima M, Kumazawa N, Iwamoto S, Seki M (2002a) Characterization of spontaneous transformation-based droplet formation during microchannel emulsification. J Phys Chem B 106:9405–9409

    Article  Google Scholar 

  • Sugiura S, Nakajima M, Seki M (2002b) Effect of channel structure on microchannel emulsification. Langmuir 18:5708–5712

    Article  Google Scholar 

  • Thorsen T, Roberts RW, Arnold FH, Quake SR (2001) Dynamic pattern formation in a vesicle-generating microfluidic device. Phys Rev Lett 86:4163–4166

    Article  Google Scholar 

  • Utada AS, Lorenceau E, Link DR, Kaplan PD, Stone HA, Weitz DA (2005) Monodisperse double emulsions generated from a microcapillary device. Science 308:537–541

    Article  Google Scholar 

  • Utada AS, Chu LY, Fernandez-Nieves A, Link DR, Holtze C, Weitz DA (2007) Dripping, jetting, drops, and wetting: the magic of microfluidics. MRS Bull 32:702–708

    Article  Google Scholar 

  • van Dijke KC, Veldhuis G, Schroën K, Boom R (2009a) Simultaneous formation of many droplets in a single microfluidic droplet formation unit. AIChE J 56:833–836

    Google Scholar 

  • van Dijke K, Veldhuis G, Schroën K, Boom R (2009b) Parallelized edge-based droplet generation (EDGE) devices. Lab Chip 9:2824–2830

    Article  Google Scholar 

  • van Dijke K, Kobayashi I, Schroën K, Uemura K, Nakajima M, Boom R (2010) Effect of viscosities of dispersed and continuous phases in microchannel oil-in-water emulsification. Microfluid Nanofluid 9:77–85

    Article  Google Scholar 

  • Vladisavljević GT, Schubert H (2003a) Influence of process parameters on droplet size distribution in SPG membrane emulsification and stability of prepared emulsion droplets. J Membr Sci 225:15–23

    Article  Google Scholar 

  • Vladisavljević GT, Schubert H (2003b) Preparation of emulsions with a narrow particle size distribution using microporous α-alumina membranes. J Disper Sci Technol 24:811–819

    Article  Google Scholar 

  • Vladisavljević GT, Williams RA (2006) Manufacture of large uniform droplets using rotating membrane emulsification. J Colloid Interface Sci 299:396–402

    Article  Google Scholar 

  • Vladisavljević GT, Shimizu M, Nakashima T (2006) Production of multiple emulsions for drug delivery systems by repeated SPG membrane homogenization: influence of mean pore size, interfacial tension and continuous phase viscosity. J Membr Sci 284:373–383

    Article  Google Scholar 

  • Vladisavljević GT, Kobayashi I, Nakajima M (2008) Generation of highly uniform droplets using asymmetric microchannels fabricated on a single crystal silicon plate: effect of emulsifier and oil types. Powder Technol 183:37–45

    Article  Google Scholar 

  • Williams RA, Peng SJ, Wheeler DA, Morley NC, Taylor D, Whalley M, Houldsworth DW (1998) Controlled production of emulsions using a crossflow membrane. Part II. Industrial scale manufacture. Chem Eng Res Des 76:902–910

    Article  Google Scholar 

  • Xu Q, Nakajima M (2004) The generation of highly monodisperse droplets through the breakup of hydrodynamically focused microthread in a microfluidic device. Appl Phys Lett 83:3726–3728

    Article  Google Scholar 

  • Yobas L, Martens S, Ong WL, Ranganathan N (2006) High-performance flow-focusing geometry for spontaneous generation of monodispersed droplets. Lab Chip 6:1073–1079

    Article  Google Scholar 

Download references

Acknowledgments

This study was supported by the Japan Society for the Promotion of Science, Tokyo (the invitation fellowship of Dr. Goran Vladisavljević ID No. L-05555), and by the Food Nanotechnology Project of the Ministry of Agriculture, Forestry and Fisheries of Japan.

Author information

Authors and Affiliations

  1. Chemical Engineering Department, Loughborough University, Loughborough, Leicestershire, LE11 3TU, UK

    Goran T. Vladisavljević

  2. Laboratory of Chemical Dynamics, Vinča Insitute of Nuclear Sciences, P.O. Box 522, 11001, Belgrade, Serbia

    Goran T. Vladisavljević

  3. National Food Research Institute, National Agriculture and Food Research Organization, Kannondai 2-1-12, Tsukuba, Ibaraki, 305-8642, Japan

    Isao Kobayashi & Mitsutoshi Nakajima

  4. Graduate School of Life and Environmental Sciences, University of Tsukuba, 1-1-1, Tennoudai, Tsukuba, Ibaraki, 305-8572, Japan

    Mitsutoshi Nakajima

Authors
  1. Goran T. Vladisavljević
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Isao Kobayashi
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Mitsutoshi Nakajima
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to Goran T. Vladisavljević or Isao Kobayashi.

Appendix

Appendix

See Tables 2, 3, and 4.

Table 2 Typical transmembrane flux, mean droplet size and span of particle size distribution in membrane emulsification (ME)
Full size table
Table 3 Typical plate dimensions, number of MCs, average size of resultant droplets, and maximum throughput of grooved and straight-through silicon MC plates
Full size table
Table 4 The average droplet size, CV of droplet diameter and droplet throughput in straight-through MC emulsification
Full size table

Rights and permissions

Reprints and permissions

About this article

Cite this article

Vladisavljević, G.T., Kobayashi, I. & Nakajima, M. Effect of dispersed phase viscosity on maximum droplet generation frequency in microchannel emulsification using asymmetric straight-through channels. Microfluid Nanofluid 10, 1199–1209 (2011). https://doi.org/10.1007/s10404-010-0750-9

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10404-010-0750-9

Keywords

Search

Navigation