Skip to main content
SpringerLink
Log in

Potential utilization of rubberwood flour and sludge waste from natural rubber manufacturing process as reinforcement in plastic composites

  • ORIGINAL ARTICLE
  • Published:
Journal of Material Cycles and Waste Management Aims and scope Submit manuscript

Abstract

The present study aims to evaluate and compare the potential of rubberwood flour (RWF) and sludge waste from manufacturing process of the concentrated natural rubber latex as reinforcement in recycled high-density polyethylene (rHDPE) composites. Morphological, thermal, mechanical and physical properties were investigated. The results indicated that the tensile modulus (TM), modulus of elasticity (MOE) and hardness of rHDPE composites containing sludge waste flour (SWF) were improved with the increasing amount of SWF; however, the tensile strength (TS), modulus of rupture (MOR) and water absorption (WA) exhibited a negative correlation with the SWF concentration. The composites based on SWF exhibited better TS, MOR, maximum flexural strain and WA than that of based on RWF. The thermal experiments showed that the decomposition temperatures of the rHDPE composites with SWF were higher than that of with RWF. Further, the addition of maleic anhydride-grafted polyethylene improved the mechanical and physical properties of the composites reinforcing the SWF or RWF. The above results showed that the utilization of latex sludge waste could become a promising way for solving the environmental problem as well as improving many properties of plastic composites.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9

Similar content being viewed by others

References

  1. Tekprasit V (2000) The utilization of the centrifuged residue from concentrated latex industry as a soil conditioner. Thesis, Prince of Songkla University

  2. Vichaphund S, Intiya W, Kongkaew A, Loykulnant S, Thavorniti P (2012) Utilization of sludge waste from natural rubber manufacturing process as a raw material for clay-ceramic production. Environ Technol 33(22):2507–2510

    Article  Google Scholar 

  3. Intiya W, Thepsuwan U, Sirisinha C, Sae-Oui P (2017) Possible use of sludge ash as filler in natural rubber. J Mater Cycles Waste Manag 19:774–781

    Article  Google Scholar 

  4. Taweepreda W (2013) Rubber recovery from centrifuged natural rubber latex residue using sulfuric acid. Songklanakarin J Sci Technol 35(2):213–216

    Google Scholar 

  5. Boonsawang P, Laeh S, Intrasungkha N (2008) Enhancement of sludge granulation in anaerobic treatment of concentrated latex wastewater. Songklanakarin J Sci Technol 30(Suppl.1):111–119

    Google Scholar 

  6. Soucy J, Koubaa A, Migneaulta S, Riedl B (2014) The potential of paper mill sludge for wood–plastic composites. Ind Crops Prod 54:248–256

    Article  Google Scholar 

  7. Hamzeh Y, Ashori A, Mirzaei B (2011) Effects of waste paper sludge on the physico-mechanical properties of high density polyethylene/wood flour composites. J Polym Environ 19:120–124

    Article  Google Scholar 

  8. Ayrilmis N, Buyuksari U (2010) Utilization of olive mill sludge in manufacture of lignocellulosic/polypropylene composite. J Mater Sci 45:1336–1342

    Article  Google Scholar 

  9. Keskisaari A, Karki T (2016) Raw material potential of recyclable materials for fiber composites: a review study. J Mater Cycles Waste Manag. https://doi.org/10.1007/s10163-016-0511-2

    Google Scholar 

  10. Homkhiew C, Ratanawilai T, Thongruang W (2015) Minimizing the creep of recycled polypropylene/rubberwood flour composites with mixture design experiments. J Compos Mater 49:17–26

    Article  Google Scholar 

  11. Adhikary KB, Pang S, Staiger MP (2008) Dimensional stability and mechanical behaviour of wood–plastic composites based recycled and virgin high-density polyethylene (HDPE). Compos Part B Eng 39(5):807–815

    Article  Google Scholar 

  12. Yao F, Wu Q, Lei Y, Xu Y (2008) Rice straw fiber-reinforced high-density polyethylene composite: effect of fiber type and loading. Ind Crop Prod 28(1):63–72

    Article  Google Scholar 

  13. Wu C, Williams PT (2010) Pyrolysis-gasification of post-consumer municipal solid plastic waste for hydrogen production. Int J Hydrogen Energy 35:949–957

    Article  Google Scholar 

  14. Parparita E, Uddin A, Watanabe T, Kato Y, Yanik J, Vasile C (2015) Gas production by steam gasification of polypropylene/biomass waste composites in a dual-bed reactor. J Mater Cycles Waste Manag 17:756–768

    Article  Google Scholar 

  15. Homkhiew C, Ratanawilai T, Thongruang W (2014) Optimizing the formulation of polypropylene and rubberwood flour composites for moisture resistance by mixture design. J Reinf Plast Compos 33:810–823

    Article  Google Scholar 

  16. Khan ZA, Kamaruddin S, Siddiquee AN (2010) Feasibility study of use of recycled high density polyethylene and multi response optimization of injection moulding parameters using combined grey relational and principal component analyses. Mater Des 31(6):2925–2931

    Article  Google Scholar 

  17. Ratanawilai T, Nakawirot K, Deachsrijan A, Homkhiew C (2014) Influence of wood species and particle size on mechanical and thermal properties of wood-polypropylene composites. Fibers Polym 15(10):2160–2168

    Article  Google Scholar 

  18. Väisänen T, Haapala A, Lappalainen R, Tomppo L (2016) Utilization of agricultural and forest industry waste and residues in natural fiber-polymer composites: a review. Waste Manag 54:62–73

    Article  Google Scholar 

  19. Sommerhuber PF, Welling J, Krause A (2015) Substitution potentials of recycled HDPE and wood particles from post-consumer packaging waste in wood–plastic composites. Waste Manag 46:76–85

    Article  Google Scholar 

  20. Zadeh KM, Ponnamma D, Al-Maadeed MAA (2017) Date palm fibre filled recycled ternary polymer blend composites with enhanced flame retardancy. Polym Test 61:341–348

    Article  Google Scholar 

  21. Al-Kaabi K, Al-Khanbashi A, Hammami A (2005) Date palm fibers as polymeric matrix reinforcement: DPF/polyester composite properties. Polym Compos 26:604–613

    Article  Google Scholar 

  22. Petchpradab P, Yoshida T, Charinpanitkul T, Matsumura Y (2009) Hydrothermal pretreatment of rubber wood for the saccharification process. Ind Eng Chem Res 48(9):4587–4591

    Article  Google Scholar 

  23. Devi RR, Maji TK (2002) Studies of properties of rubber wood with impregnation of polymer. Bull Mater Sci 25:527–531

    Article  Google Scholar 

  24. Wu H, Liang X, Huang L, Xie Y, Tan S, Cai X (2016) The utilization of cotton stalk bark to reinforce the mechanical and thermal properties of bio-flour plastic composites. Constr Build Mater 118:337–343

    Article  Google Scholar 

  25. Yang S, Bai S, Wang Q (2016) Morphology, mechanical and thermal oxidative aging properties of HDPE composites reinforced by nonmetals recycled from waste printed circuit boards. Waste Manag 57:168–175

    Article  Google Scholar 

  26. Ponnamma D, George J, Thomas MG, Han CC, Valic´ S, Mozetic M, Cvelbar U, Thomas S (2015) Investigation on the thermal and crystallization behavior of high density polyethylene/acrylonitrile butadiene rubber blends and their composites. Polym Eng Sci 55:1203–1210

    Article  Google Scholar 

  27. Sadasivuni KK, Saiter A, Gautier N, Thomas S, Grohens Y (2013) Effect of molecular interactions on the performance of poly(isobutylene-co-isoprene)/graphene and clay nanocomposites. Colloid Polym Sci 291:1729–1740

    Article  Google Scholar 

  28. Xu K, Tu D, Chen T, Zhong T, Lu J (2016) Effects of environmental-friendly modified rubber seed shell on the comprehensive properties of high density polyethylene/rubber seed shell composites. Ind Crop Prod 91:132–141

    Article  Google Scholar 

  29. Yang H, Yan R, Chen H, Lee DH, Zheng C (2007) Characteristics of hemicellulose, cellulose and lignin pyrolysis. Fuel 86(12–13):1781–1788

    Article  Google Scholar 

  30. Essabir H, Boujmal R, Bensalah MO, Rodrigue D, Bouhfid R, Qaiss A (2016) Mechanical and thermal properties of hybrid composites: oil-palm fiber/clay reinforced high density polyethylene. Mech Mater 98:36–43

    Article  Google Scholar 

  31. Ayrilmisa N, Kaymakci A, Gülec T (2015) Potential use of decayed wood in production of wood plastic composite. Ind Crop Prod 74:279–284

    Article  Google Scholar 

  32. Mattos BD, Misso AL, Cademartori PHG, Limad EA, Washington LE, Magalhãesd WLE, Gatto DA (2014) Properties of polypropylene composites filled with a mixture of household waste of mate-tea and wood particles. Constr Build Mater 61:60–68

    Article  Google Scholar 

  33. Ratanawilai T, Thanawattanasirikul N, Homkhiew C (2012) Mechanical and thermal properties of oil palm wood sawdust reinforced post-consumer polyethylene composites. ScienceAsia 38:289–294

    Article  Google Scholar 

  34. Sheshmani S, Amini R (2013) Preparation and characterization of some graphene based nanocomposite materials. Carbohydr Polym 95(1):348–359

    Article  Google Scholar 

  35. Nourbakhsh A, Ashori A, Tabari HZ, Rezaei F (2010) Mechanical and thermo-chemical properties of wood-flour/polypropylene blends. Polym Bull 65(7):691–700

    Article  Google Scholar 

  36. Ashori A, Nourbakhsh A (2009) Mechanical behavior of agro-residue-reinforced polypropylene composites. J Appl Polym Sci 111(5):2616–2620

    Article  Google Scholar 

  37. Kord B (2011) Effect of wood flour content on the hardness and water uptake of thermoplastic polymer composites. World Appl Sci J 12:1632–1634

    Google Scholar 

  38. Rahman MR, Huque MM, Islam MN, Hasan M (2008) Improvement of physico-mechanical properties of jute fiber reinforced polypropylene composites by post-treatment. Compos Part A Appl Sci Manuf 39(11):1739–1747

    Article  Google Scholar 

  39. Law TT, Mohd Ishak ZA (2011) Water absorption and dimensional stability of short kenaf fiber-filled polypropylene composites treated with maleated polypropylene. J Appl Polym Sci 120(1):563–572

    Article  Google Scholar 

  40. Homkhiew C, Ratanawilai T, Thongruang W (2016) Long-term water absorption and dimensional stability of composites from recycled polypropylene and rubberwood flour. J Thermoplast Compos Mater 29(1):74–91

    Article  Google Scholar 

  41. Adhikary KB, Pang S, Staiger MP (2008) Long-term moisture absorption and thickness swelling behaviour of recycled thermoplastics reinforced with Pinus radiate sawdust. Chem Eng J 142(2):190–198

    Article  Google Scholar 

  42. Shakeri A, Ghasemian A (2010) Water absorption and thickness swelling behavior of polypropylene reinforced with hybrid recycled newspaper and glass fiber. Appl Compos Mater 17(2):183–193

    Article  Google Scholar 

  43. Lin Q, Zhou X, Dai J (2002) Effect of hydrothermal environment on moisture absorption and mechanical properties of wood flour-filled polypropylene composites. J Appl Polym Sci 85(14):2824–2832

    Article  Google Scholar 

  44. Sathishkumar TP, Navaneethakrishnan P, Shankar S et al (2013) Mechanical properties and water absorption of snake grass longitudinal fiber reinforced isophthalic poly-ester composites. J Reinf Plast Compos 32:1211–1223

    Article  Google Scholar 

  45. Ashori A, Sheshmani S (2010) Hybrid composites made from recycled materials: moisture absorption and thickness swelling behavior. Bioresour Technol 101(12):4717–4720

    Article  Google Scholar 

  46. Ghasemi I, Kord B (2009) Long-term water absorption behaviour of polypropylene/wood flour/organoclay hybrid nanocomposite. Iran Polym J 18(9):683–691

    Google Scholar 

Download references

Acknowledgements

This work was financially supported from the Government budget Fund (Research Grant Code: 2559A17102098) and the Rajamangala University of Technology Srivijaya (RMUTSV), Thailand. I also want to convey my thanks to Dr. Marwan Affandi from The Faculty of Engineering RMUTSV who has checked my paper.

Author information

Authors and Affiliations

  1. Materials Processing Technology Research Unit, Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Srivijaya, Muang District, Songkhla, 90000, Thailand

    Chatree Homkhiew, Worapong Boonchouytan & Watthanaphon Cheewawuttipong

  2. Department of Industrial Engineering, Faculty of Engineering, Prince of Songkla University, Hat Yai, Songkhla, 90112, Thailand

    Thanate Ratanawilai

Authors
  1. Chatree Homkhiew
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Worapong Boonchouytan
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Watthanaphon Cheewawuttipong
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Thanate Ratanawilai
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Chatree Homkhiew.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Homkhiew, C., Boonchouytan, W., Cheewawuttipong, W. et al. Potential utilization of rubberwood flour and sludge waste from natural rubber manufacturing process as reinforcement in plastic composites. J Mater Cycles Waste Manag 20, 1792–1803 (2018). https://doi.org/10.1007/s10163-018-0749-y

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10163-018-0749-y

Keywords

Search

Navigation