Urea-formaldehyde microspheres as a potential additive to wood adhesive
- 403 Downloads
Urea formaldehyde (UF) resins are important for wood industry due to their attractive properties at reasonable price. Particulate fillers added to UF are of interest with regard to improving the functionality of UF and also in terms of reduced UF consumption. To study their potential as filler, solid UF microspheres were synthesized and characterised respecting its morphology, chemical curing and thermal stability. Marigold flower structured spheres with diameters between 5 and 20 µm are presented and application trials demonstrated that high amounts of UF may be replaced by solid microspheres without impairing adhesive bond strength of solid wood bond lines. Fluorescence microscopy showed that microspheres greatly reduce adhesive penetration into the wood substrate, retaining the modified adhesive in the bondline. UF microspheres may thus be considered as viable filler for UF adhesives, particularly with regard to the possibility of endowing them with added functionality like self-healing properties.
KeywordsMicroparticles Microscopy (optical, electron, fluorescence) Resin substitution Encapsulation
Urea formaldehyde (UF) resins are widely used in wood industry because of their high reactivity, low cost and easy processing. Nearly all particleboards for indoor uses are bonded with UF resins despite ongoing concerns due to the critical discussion of formaldehyde emissions from this popular adhesive . Hence, there is considerable pressure towards either replacing formaldehyde-based resins completely or substantially reducing formaldehyde emissions from adhesively bonded wood products. Modifications in the chemistry of UF, e.g., reductions in the molar ratio between urea and formaldehyde used in UF synthesis, have brought significant progress in emission reduction [2, 3]. An alternative strategy consists in the incorporation of non-UF additives either as formaldehyde scavenger or as UF-replacement.
As an example, hydrolysed soy protein isolates were added to UF, which increased bonding strength, biodegradability and reduced formaldehyde emissions . Corn flour improved mechanical performance and reduced formaldehyde emissions if added to UF . A substitution up to 20% UF resin was reported using liquefied wood without impairing the mechanical properties of particleboards . The co-condensation of UF with furfural proved to be feasible and resulted in reduced formaldehyde emissions at the expense of significantly increasing the necessary pressing temperatures .
Particulate additives may also reduce emissions from UF. Nanoclay was added to UF with the help of a coupling agent substituting up to 6% resin without negatively affecting its properties  or even improving its properties . All these findings have shown that a substitute of a few percent of UF resin is possible without diminishing its properties. Silanised nanocellulose was also used successfully to reduce emissions while at the same time providing improved mechanical performance .
Besides formaldehyde emission, also the brittleness of cured UF resin presents a rewarding target for improvement . Inorganic particles such as nanoclay [8, 9, 12, 13, 14, 15] and cellulose nanoparticles [16, 17, 18] were successfully used as modifiers improving adhesive toughness and bond strength. Urea-modified scallop shell nanoparticles were added to plywood adhesives to reduce formaldehyde emissions .
In parallel to formaldehyde emission and adhesive mechanics, the addition of particulate fillers with high specific surface area, also significantly affected adhesive viscosity and, in turn, adhesive penetration into the bulk wood during application . It is common sense in wood technology that adhesive penetration may be regarded as an indication of good wetting and that a certain penetration of adhesive into the wood bulk favours mechanical interlocking . On the other hand, excessive penetration of adhesive is unwanted because this adhesive fraction does not directly contribute to the build-up of an adhesive bond line between neighbouring wood particles .
In summary, the addition of particulate fillers may be of interest towards improving bond performance and saving adhesive. Therefore, the present study focuses on expanding the available portfolio of potential particulate fillers for wood adhesives. Ideally, particulate filler should show good surface-chemical compatibility with UF, and a high specific surface area. These prerequisites are fulfilled by UF-microspheres , which are chemically identical with an UF wood adhesive and comprise of a high specific surface area. In the present study, UF-microspheres are synthesised and their suitability as an additive for improving UF adhesive bonds is elucidated.
For the synthesis of UF microspheres according to the procedure described in reference , 0.1 g 2-hydroxyethyl cellulose (CAS Nr. 9004-62-0, Sigma-Aldrich Chemie GmbH, Germany) was dissolved in 100 ml distilled water at 50 °C for 30 min under permanent stirring. Preliminary trials showed that hydroxyethyl cellulose with a molecular weight of 9 × 104 g/mol yielded ideal spherical particles, whereas higher molecular weight of 1.3 × 106 g/mol resulted in particles with heavily distorted geometry. Therefore, the low-molecular weight variant was finally used. Subsequently, 8.11 g formaldehyde solution (37%, CAS Nr. 50-00-0, Carl Roth GmbH & Co. KG, Germany) was added, followed by the addition of 3 g crystalline urea (> 99.5%, CAS Nr. 57-13-6, Carl Roth GmbH & Co. KG, Germany). The pH of the formulation was adjusted to pH 4 with droplets of sodium hydroxide (0.1 mol/l, CAS Nr. 1310-73-2, Carl Roth GmbH & Co. KG, Germany). After the addition of all chemicals, stirring was stopped and the temperature was kept at 50 °C for 3 h. After a resting time of 24 h, the microspheres had settled at the bottom of the flask. As a last step the supernatant was decanted, the spheres were washed with distilled water and dried by slow evaporation at room temperature and ambient pressure.
For microscopic studies of spheres, the microspheres were spread on carbon adhesive tape and observed with a scanning electron microscope (SEM, Quanta FEG 250, FEI, Czech Republic), operated with 5 kV acceleration voltage. Before performing SEM studies, the microspheres were coated with gold using a sputter coater (Scancoat Six, HHV Ltd., United Kingdom) operated at 1 mbar, 20 mA and 3–4 kV for 240 s.
The adhesive bond strength of microsphere-modified UF was evaluated using an industrial UF resin (10F102, Metadynea, Austria) to glue flawless beech veneers (Fagus sylvatica L.) for tensile shear testing inspired by EN 302-1 . Strips of veneer (150 × 20 × 0.5 mm3) were glued with an overlapping area of 5 × 20 mm2 and an adhesive spread of 200 g/m2. UF microspheres were added to the adhesive at ratios of 0.0:1, 0.1:1, 0.5:1, and 1:1 with regard to the amount of solid UF present in the resin. Ammonium nitrate solution (60%, CAS Nr. 6484-52-2, Carl Roth GmbH & Co. KG, Germany) was used as hardener and its content was kept constant at 3% to the amount of solid resin in the system. For all formulations, the water content was adjusted in a manner that it was constant in relation to the sum of UF-microparticles, solid hardener and solid UF resin in the system. Prior to bonding, the adhesive formulations were exposed to an ultrasonic treatment for 3 min at 320 W and 35 kHz (DT 100 H, Bandelin electronic, Germany).
Viscosity of each formulation was measured 3 times at a constant shear rate of 10 s−1 with a cone-plate rheometer (Bohlin Instruments CVO, Cranbury, USA) at 20 °C, for 240 s, with 10 interpolation steps from which the penultimate values were used. To determine the pot life of adhesive formulations, the rheometer was adjusted to 40 °C and 3 measurements were executed immediately after adding the hardener and after 1 and 2 h.
Both, specimen preparation (i.e., bonding of strips) and subsequent tensile testing were performed on a Zwick/Roell Z100 universal testing machine (Zwick GmbH & Co. KG, Germany) equipped with a 5 kN load cell and an electrically heated press. The glued strips were mounted to the testing machine and pressed together at 90 or 120 °C for 2 min at a pressure of 25 kPa. Afterwards, the pressure was released and the sample was immediately tested to failure at a speed of 1.5 mm/min. For each adhesive formulation, a minimum of six specimens were tested, resulting in 85 specimens in total.
To characterise the cure dynamics of UF adhesive in the presence of UF microspheres, simultaneous thermal analysis (STA) was performed using a Netzsch STA 409 PG/1/G Luxx® (Netzsch Gerätebau GmbH, Germany). 4 mg of adhesive formulation (UF resin, hardener, UF microspheres and water) were put in Al2O3 crucibles, closed and pierced. Under nitrogen atmosphere (flow rate 50 ml/min) the crucibles were heated from 25 to 300 °C at a heating rate of 10 K/min.
Wood specimens tested for adhesive bond strength were examined after failure using fluorescence microscopy to quantify penetration depth of the adhesive into the wood structure. Specimens measuring 5 × 20 mm2 were cut from the middle of the veneers’ overlapping area with a sharp paring chisel. They were immersed in a 0.1% Brilliant Sulphaflavine solution (CAS Nr. 2391-30-2, Sigma-Aldrich Chemie GmbH, Germany), a yellow fluorescent dye which bonds selectively to basic amino-groups , to stain the adhesive, for 2 min. After a washing step with H2O, a second immersing step in a 0.1% Gentian Violet solution (CAS Nr. 548-62-9, Sigma-Aldrich Chemie GmbH, Germany) was added to stain the wood and create a good contrast between wood and adhesive . Air-dried stained specimens were observed using a reflected-light microscope (Axioplan2, Carl Zeiss AG, Germany) with a 2.5 × EC Epiplan-Neofluar objective mounted. A UV-lamp and the excitation filter Zeissset02 (365 nm) was used. Pictures were captured using a camera (Axiocam Hrc, Carl Zeiss AG, Germany) operated in RGB-mode. Digital image analysis was performed with ImageJ  creating one binary image of glue and one binary image of veneers bottom line.
The penetration depth was quantified in MATLAB (MathWorks Inc., USA), whereas both binary images (glue and bottom line) as well as the thickness measurements of veneers were imported. The resolution of the images (4.147 µm/pixel) was set as variable for the subsequent calculations. The bottom line was then smoothed to remove artefacts from the thresholding, using a moving average with a window length of 70 pixels. In preliminary tests, this window length was found to represent the given bottom lines most precisely. Afterwards the Euclidean distance was calculated from each single adhesive pixel to all pixels of the bottom line. The shortest Euclidean distance was selected and the veneer thickness was subtracted. This value was considered to be the penetration depth of single adhesive pixels in relation to the glued wood surface.
Results and discussion
The synthesis of UF-microspheres according to reference  was straightforward and resulted in UF powder as shown in Fig. 1. As expected, the particles were nicely spherical and disposed of a laminar substructure providing high specific surface area. The diameter of the spheres typically varied between 5 and 20 µm.
Different molecular weights of hydroxyethyl cellulose resulted in different shapes and surfaces of microspheres as shown in Fig. 2. At lower molecular weight, all spheres showed structured surfaces and were spherical beside a small amount with distorted geometry. With increasing molecular weight this proportion increased and especially the globular microspheres featured flat, unstructured surfaces. Dry powder as shown in Figs. 1 and 2 prepared with low molecular weight hydroxyethyl cellulose was used for all subsequent experiments without any further treatment.
Formulations of UF microspheres with an industrial adhesive prepared at different ratios exhibited different viscosities as shown in Table 1. The reference’s viscosity was around 300 mPa·s and decreased with the addition of microspheres to 200 mPa·s (− 33%). However, the viscosity of the formulation containing 1 part microspheres and 1 part resin was higher and comparable with the reference’s viscosity, measured immediately after adding the hardener. Remarkable was the high viscosity of the reference, 1 and 2 h after the hardener addition. High viscosities were also measured for the formulation 0.1:1 (microspheres:UF). After 1 h the viscosities of the reference and the 0.1:1 formulation were 1 × 103 and 650 mPa·s, so still suitable for common industrial adhesive application systems. But after 2 h the viscosities increased to nearly 7 × 104 and 3 × 104 mPa·s, so they would not be applicable anymore. However, for the formulations 0.5:1 and 1:1, viscosities below 1 × 103 mPa·s were measured. This observation can be explained by the lower content of hardener when microspheres were added, because hardener content was set constant to solid UF-resin content (3%). By adding microspheres the content of reactive UF is successively replaced by microspheres, simultaneously reducing the hardener content. After 3 h, all adhesive formulations were solid.
Viscosities of different resin-microsphere formulations measured with a cone/plate rheometer at a constant shear rate of 10 s−1, at 20 and 40 °C, immediately after hardener addition, as well as 1 and 2 h afterwards, to determine pot life
Ratio of microspheres:resin
1.02 × 103
6.81 × 104
2.91 × 104
1.34 × 103
1.07 × 103
For the evaluation of bonding strength, the different adhesive formulations were applied to wood specimens. Unlike the reference, formulations containing microspheres appeared to be too dry and solidify very quickly after application, although pot life increases. This could be an indication that the liquid part of the formulation was soaked up by the wood bulk very quickly and only the solid microspheres were visible on the veneer’s top. However, the overall processing and cure-behaviour was unaffected and comparable to the unmodified adhesive.
The adhesive bond strength of veneer specimens bonded with unmodified and microsphere-modified UF showed some effects of microsphere addition, which were, however, not significant in a statistical sense due to high variability within groups (Fig. 3). Overall, the bond strength of specimens cured at higher temperature was higher, as expected from UF cure-kinetics . The lowest average values of bond strength were observed for the two variants bonded with unmodified adhesive, with 3.1 MPa at 90 °C and 3.5 MPa at 120 °C. Consistently, for both temperatures a slight but consistent increase in bond strength with increasing microsphere content was observed (Fig. 3). In fact, the highest values for adhesive strength were measured using an adhesive formulation containing 1 part resin (dry mass basis) and 1 part microspheres cured at 120 °C. With an average value of 4.2 MPa, an increase of 20% was achieved. While these results do not demonstrate substantial improvements in bond strength, they provide clear proof that a high fraction of dry cured UF microsphere powder can be added to UF adhesive without impairing bond performance.
A comparison of the cure-kinetics of the two most extreme adhesive variants used, i.e., unmodified UF adhesive and adhesive containing equal amounts of resin and solid UF microspheres is shown in Fig. 4. While at lower temperatures the signal of differential scanning calorimetry (DSC) was primarily due to evaporating humidity, exothermal curing of the unmodified adhesive started at around 70 °C and reached a maximum at 90 °C, which is in good agreement with literature [26, 27, 28, 29].
In comparison to the unmodified adhesive, the formulation containing microspheres showed similar cure-behaviour, with the notable difference of a less intense maximum at 90 °C. This difference can be explained with the fact that the amount of reactive material was reduced by 50% in the modified adhesive. At 130 °C both formulations showed a sharp and intense endothermal peak related to endothermic formaldehyde elimination  creating ethylene bonds out of ether bonds, while releasing formaldehyde. Endothermal resin decomposition started at 215 °C for the unmodified adhesive and at 220 °C for the modified one. In good agreement with literature , the strong endothermal peak corresponds to a distinct mass-drop in the signal of thermogravimetric analysis.
In summary, the addition of UF-microspheres to UF-resin did not affect its curing behaviour. Differences in peak intensity could be explained by reaction kinetics known from literature. The finding that adhesive strength remained unaffected or even improved slightly when 50% of reactive UF resin was replaced with largely inert UF-microspheres (ratio 1:1), remained to be explained. To do so, adhesive bond lines and, in particular, adhesive penetration, was examined. Excellent contrast between the adhesive and the bulk wood was obtained with the double-staining method applied seen in Fig. 5. Already upon optical inspection, clear differences between specimens bonded with unmodified adhesive and formulations modified with UF-microspheres were clearly visible. Unmodified UF penetrated deeper into the wood (Fig. 5a, b) than the modified UF, which was concentrated close to the specimen surface (Fig. 5c, d). In quantitative terms, the average penetration was around 0.15 mm for unmodified UF and 0.08 mm for modified UF (Fig. 6).
Viscosity is a characterizing factor for the penetration behaviour of liquids. Rheological behaviour changed with the addition of microspheres. The observed initial decrease followed by a later increase in viscosity (Table 1) could be because of the microspheres’ morphology. Balls enable an easy scrolling within the UF matrix, but at certain levels the loading is too high staunching the flow of UF and microspheres. This speculation is in good comparison with a study suggesting an explanation for comparable rheological behaviour in dispersions of silica nanospheres and montmorillonite platelets and their interaction .
Penetration was measured at unmodified adhesives and with maximum addition of microspheres, whereas both formulations exhibited comparable viscosities. Thus, the viscosity can be excluded to explain decreased penetration and the microsphere addition led to a decrease of resin’s penetration depth to the half value measured at unmodified adhesive.
In addition to penetration depth, also the variability of penetration depth was significantly reduced at the modified variant, indicating a distinct concentration of adhesive close to the specimen surface. One explanation could be that the microspheres remain on the specimen surface, being solid bodies unable to penetrate the solid wood structure due to the above-micron size. It is proposed that due to the large specific surface area, substantial amounts of liquid adhesive adsorb to the surface of microspheres and consequently remain immobilised at the wood surface, reducing overall penetration. In good agreement with a recent study on UF-adhesive modified with microfibrillated cellulose  it is proposed that the concentration of adhesive at the specimen surface, provided by UF-microsphere addition, enables the formation of bonds with strength similar to unmodified adhesive. There only a fraction of adhesive contributes to bond formation while a substantial amount of resin penetrates deeply into the bulk and does not contribute to bonding.
While interesting and unexpected effects were found in the present study, its practical significance remains unclear. It is intriguing that substantial amounts of inert additive can be added to an adhesive without impairing its bond strength. This finding may provide a basis for further studies, where UF microspheres provided with added functionality such as, e.g., free methylol groups immobilizing enzymes , or microencapsulated fragrances compensating unwanted terpene smells from wood , are incorporated into the bondline. Furthermore, aminoplastics are a major polymer used in microencapsulation [33, 34]. Microencapsulation is widely discussed in terms of providing additional functionality to coatings  or polymers in general . Since the present study has shown that the addition of UF microspheres is feasible without degrading bond strength, it should also be feasible to incorporate aminoplastic microcapsules with, e.g., self-healing functionality into wood adhesive bond lines. Especially interesting for particleboard manufacturers using UF as adhesive with its high brittleness, self-healing is of high importance to enhance service life of furniture for example. Some studies already report a microencapsulation of polymerizable fluids as healing agent like dicyclopentadiene, styrene, or epoxy [37, 38, 39].
To conclude, a substitution of 50% UF resin by solid microspheres (ratio 1:1) is possible, without impairing the bonding quality of solid wood joints. This opens the option of adding a huge amount of spherical particles directly into a bond line as carrier for, e.g., formaldehyde catchers or self-healing substances. Lap shear strength indicates the quality of a wood joint and was tested at different substitution degrees and temperatures, where it did not underperform against the unmodified adhesive. The spheres did not influence the chemical curing of UF but if added, the penetration of liquid adhesive into wood was decreased by 50%. The finding that adhesive stays closer to the bond line could be preferable if self-healing substances are added to repair damaged glue joints, but this is topic of further research.
Open access funding provided by University of Natural Resources and Life Sciences Vienna (BOKU). The project was funded by the Austrian Research Promotion Agency (FFG) in collaboration with the Fritz Egger GmbH & Co., OG as industrial partner. Special thanks to Roland Mitter for DSC-measurements and to Stephan Frömel-Frybort helping with digital image analysis.
This study was funded by Austrian Research Promotion Agency (FFG, Grant number 844608).
- 1.Yu CWF, Crump DR (1999) Testing for formaldehyde emission from wood-based products—a review. Indoor Built Environ 8:280–286Google Scholar
- 3.Frackowiak I, Warcok F, Fuczek D, Andrzejak C (2011) The influence of UF molar ratio on selected particleboard properties. Drewno 54:39–49Google Scholar
- 7.Zhang JZ, Chen H, Pizzi A, Li YH, Gao Q, Li JZ (2014) Characterization and application of urea-formaldehyde-furfural co-condensed resins as wood adhesives. Bioresources 9:6267–6276Google Scholar
- 8.Xian D, Semple KE, Haghdan S, Smith GD (2013) Properties and wood bonding capacity of nanoclay-modified urea and melamine formaldehyde resins. Wood Fiber Sci 45:383–395Google Scholar
- 10.Zhang H, Zhang J, Song SP, Wu GF, Pu JW (2011) Modified nanocrystalline cellulose from two kinds of modifiers used for improving formaldehyde emission and bonding strength of urea-formaldehyde resin adhesive. Bioresources 6:4430–4438Google Scholar
- 13.Zhou X, Pizzi A, Du G (2012) The effect of nanoclay on melamine-urea-formaldehyde wood adhesives. J Adhes Sci Technol 26:1341–1348Google Scholar
- 16.Veigel S, Müller U, Konnerth J, Gindl W (2010) Cellulose fibers and nanofibrils for adhesive reinforcement. In: International Conference on Nanotechnology for the Forest Products Industry, Espoo, Finland, 27–29 Sept 2010. Proceedings pp 1370–1375Google Scholar
- 22.EN 302-1 (2013) Adhesives for load-bearing timber structures—Test methods—Part 1: determination of bond strength in longitudinal tensile shear strength. European Committee for Standardization, BrusselsGoogle Scholar
- 27.Popovic M, Miljkovic J, Simendic JB, Pavlicevic J, Ristic I (2011) Curing characteristics of low emission urea-formaldehyde adhesive in the presence of wood. Wood Res-Slovakia 56:589–599Google Scholar
- 32.Schmidt DG, Norbury RJ, Buttery HJ (1995) Coated perfume particles. European Patent Office, Vienna EP0397246Google Scholar
Open AccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.