Abstract
In flat-type light-emitting-diode (LED) lighting systems, a planar light is formed using a luminance source positioned on the side of the system and light guide panel (LGP) or reflecting plates. Thus, such systems are favorable for their thinness, which allows a relatively small number of LEDs to be used. However, the application of a high-power LED light to a large-area lighting system yields Lambertian luminaires; therefore, a point or a discomfort glare is produced, which generally causes degradation of the luminance efficiency and uniformity. In this study, we solved the problems of luminance non-uniformity and inefficiency by adjusting the orientation of an applied LGP scattered pattern and removing the remaining glare. Through computer simulation, optical characteristics that increase the efficiency even in the case of low-output LEDs were found. Specifically, a scattered pattern vertically oriented relative to the direction of the incident light improves the luminance uniformity at the side of the system, while a scattered pattern oriented parallel to the direction of the incident light plays the role of a waveguide. We implemented a flat-type LED lighting system by fabricating a large-area LGP based on the computer-simulation results and using an extremely sensitive laser. The optical characteristics observed using the laser-processed LGP were identical to those obtained in the computer simulation. Therefore, for large-area flat-type LED lighting systems, we confirmed that adjusting the orientation of the LGP scattered pattern can increase the luminance efficiency and uniformity.
Similar content being viewed by others
References
Kim, T.H., Park, S.H., Oh, H.K., Shin, Y.J.: Analysis of the laser patterning inside light guide panel. Opt. Laser Technol. 39, 1437 (2007)
Choi, E.S., Choi, Y.H., Shin, Y.J.: Light manipulation in a transparent medium with laser-patterned three-dimensional and surface scatterers. J. Korean Phys. Soc. 55, 2646 (2009)
Kim, Y.C., Kim, D.W., Oh, T.S., Lee, Y.M., Ahn, S., Kim, Y.C.: LGP pattern design by using a pattern density function with simple exponential function. Korean J. Opt. Photon. 21, 97 (2010)
Kim, Y.C.: LGP pattern design with single LED light source. Optik. 125, 1341 (2014)
Park, S.H., Lee, S.S., Ma, H.J., Choi, E.S., Shin, Y.J.: Simulation of luminance and uniformity of LGP according to the laser scattering pattern. Korean J. Opt. Photon. 21, 225 (2010)
Park, S.H., Shin, Y.J., Choi, E.S., Ma, H.J., Lee, S.S.: Improvement of luminance and uniformity of light guide panel using scatterer pattern by laser processing. Opt. Laser Technol. 44, 1301 (2012)
Park, S.H., Shin, Y.J.: Quantitative analysis of the dependence of the luminance of the light guide plate for a LCD backlight on the scattering angle of the optical patterns. New Phys. Sae Mulli. 64, 934 (2014)
Lee, J.H., Nahm, B.B., Ko, J.H., Kim, J.H.: Optimization of optical structure of light guide panel for uniformity improvement of edge-lit backlight. Korean J. Opt. Photon. 21, 61 (2010)
Lee, S.S., Choi, E.S., Shin, Y.J.: Use of simulation to design the optical scattering pattern for LED lighting. New Phys. Sae Mulli. 63, 1027 (2013)
Lee, J.Y., Shin, M.H., Kim, J.S., Kim, Y.J.: Design of light guide plate to improve optical characteristics for large-area edge-lit LED display. Trans Soc Inf Storage Syst. 9, 10 (2013)
Park, S.H., Shin, Y.J.: Optimization of the reflector and the light guide panel for improving the uniformity of large-area flat-type LED lighting. New Phys. Sae Mulli. 64, 825 (2014)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Park, S., Shin, Y., Oh, K. et al. Optical characteristics of LGP depending on the scattering pattern orientation for flat-type LED lighting. Opt Rev 23, 172–179 (2016). https://doi.org/10.1007/s10043-016-0193-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10043-016-0193-y