Abstract
A dip-coating method to fabricate anode-supported tubular solid oxide fuel cells has been successfully developed. The length, outside diameter, and thickness of the single cell are 10.8 cm, 1.0 cm, and 0.6 mm, respectively. The area of the cathode is 15–16 cm2 (cathode length = 4.8 cm). The cell consists of a Ni-YSZ anode support tube, a Ni-ScSZ anode functional layer, a ScSZ electrolyte film, a LSM-ScSZ cathode functional layer, and a LSM cathode current collecting layer. A preliminary examination of the single tubular cell has been carried out and an acceptable performance was obtained. The maximum power density was, respectively, 325, 276, 208, and 168 mW cm−2 at 850, 800, 750, and 700 °C, when operating with humidified hydrogen.
Similar content being viewed by others
References
Du Y, Sammes NM (2004) J Power Sources 136:66. doi:10.1016/j.jpowsour.2004.05.028
Dong D, Gao J, Liu X, Meng G (2007) J Power Sources 165:217. doi:10.1016/j.jpowsour.2006.10.098
Setoguchi T, Sawano M, Eguchi K, Arai H (1990) Solid State Ion 40–41:502. doi:10.1016/0167-2738(90)90390-D
Schoonman J, Dekker JP, Broers JW, Kiwiet NJ (1991) Solid State Ion 46:299. doi:10.1016/0167-2738(91)90229-5
van Dieten VEJ, Schoonman J (1992) Solid State Ionics 57:141. doi:10.1016/0167-2738(92)90076-2
Chen CC, Nasrallah MM, Anderson HU (1994) Solid State Ion 70–71:101. doi:10.1016/0167-2738(94)90293-3
Hibino T, Hashimoto A, Asano K, Yano M, Suzuki M, Sano M (2002) Electrochem Solid-State Lett 5:A242. doi:10.1149/1.1508551
Shao Z, Haile SM (2004) Nature 431:170. doi:10.1038/nature02863
Steele BCH (1999) Nature 400:619. doi:10.1038/23144
Tsai T, Barnett SA (1995) J Electrochem Soc 142:3084–3087. doi:10.1149/1.2048692
de Souza S, Visco SJ, De Jonghe LC (1997) J Electrochem Soc 144:L35. doi:10.1149/1.1837484
Muccillo P, Muccillo ENS, Fonseca FC, Franca YV, Porfirio TC, de Florio DZ, Berton MAC, Garcia CM (2006) J Power Sources 156:455. doi:10.1016/j.jpowsour.2005.06.021
Sammes NM, Du Y, Bove R (2005) J Power Sources 145:428. doi:10.1016/j.jpowsour.2005.01.079
Kendall K, Palin M (1998) J Power Sources 71:268. doi:10.1016/S0378-7753(97)02761-4
Yashiro K, Yamada N, Kawada T, Hong J, Kaimai A, Nigara Y, Mizusaki J (2002) Electrochemistry 70(12):958
Kim JH, Songa RH, Song KS, Hyun SH (2003) J Power Sources 122:138. doi:10.1016/S0378-7753(03)00431-2
Suzuki T, Yamaguchi T, Fujishiro Y, Awano M (2006) J Power Sources 160:73. doi:10.1016/j.jpowsour.2006.01.037
Funahashi Y, Shimamori T, Suzuki T (2007) J Power Sources 163:731. doi:10.1016/j.jpowsour.2006.10.002
Li CJ, Li CX, Xing YZ, Gao M, Yang GJ (2006) Solid State Ion 177:2065. doi:10.1016/j.ssi.2006.03.004
Li CJ, Li CX, Ning XJ (2004) Vacuum 73:699. doi:10.1016/j.vacuum.2003.12.096
Li S, Wang S, Nie H, Wen T (2006) J Solid State Electrochem 11:59. doi:10.1007/s10008-005-0067-x
Kim JH, Song RH, Song KS, Hyun SH (2003) J Power Sources 122:138. doi:10.1016/S0378-7753(03)00431-2
Haanappel VAC, Mertens J, Rutenbeck D, Tropartz C, Herzhof W, Sebold D, Tietz F (2005) J Power Sources 141:216. doi:10.1016/j.jpowsour.2004.09.016
Yamamoto O (2000) Electrochim Acta 45:2423. doi:10.1016/S0013-4686(00)00330-3
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Liu, R.Z., Wang, S.R., Huang, B. et al. Dip-coating and co-sintering technologies for fabricating tubular solid oxide fuel cells. J Solid State Electrochem 13, 1905–1911 (2009). https://doi.org/10.1007/s10008-008-0752-7
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10008-008-0752-7