Abstract
An analytical model is developed to predict the elastic stress response of a thick-walled cylindrically curved panel subjected to a radial temperature gradient under the assumption of generalized plane strain. The ends of the panel in the angular direction are guided by rigid supports that allow a displacement in the circumferential direction but fix the curvature of the middle surface. As thermal load is applied to the panel, couples act on those ends, giving rise to pure bending conditions even in the case of homogeneous heating. Moreover, the free ends in the axial direction of the panel are taken into consideration. The stresses caused by different types of steady-state thermal loads in the panel are analyzed. Further, the elastic limits leading to plastic flow according to the yield criteria of both Tresca and von Mises are investigated. The results are presented in graphical form.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Timoshenko, S.P., Goodier, J.N.: Theory of Elasticity. McGraw-Hill, New York (1970)
Eraslan, A.N., Arslan, E.: A computational study on the nonlinear hardening curved beam problem. Int. J. Pure Appl. Math. 43, 129–143 (2008)
Dryden, J.: Bending of in homogeneous curved bars. Int. J. Solids Struct. 44, 4158–4166 (2007)
Arslan, E., Eraslan, A.N.: Bending of graded curved bars at elastic limits and beyond. Int. J. Solids Struct. 50, 806–814 (2013)
Arslan, E., Sülü, İ.Y.: Yielding of two-layer curved bars under pure bending. Z. Angew. Math. Mech. 94, 713–720 (2014)
Eraslan, A.N., Arslan, E.: A concise analytical treatment of elastic–plastic bending of a strain hardening curved beam. Z. Angew. Math. Mech. 88, 600–616 (2008)
Dadras, P.: Plane strain elastic–plastic bending of a strain hardening curved beam. Int. J. Mech. Sci. 43, 39–56 (2001)
Shaffer, B.W., House, R.N. Jr.: Displacements in a wide curved bar subjected to pure elastic–plastic bending. J. Appl. Mech. Trans. ASME 24, 447–452 (1957)
Arslan, E., Eraslan, A.N.: Analytical solution to the bending of a nonlinearly hardening wide curved bar. Acta Mech. 210, 71–84 (2010)
Boley, B. A., Barrekette, E.S.: Thermal stress in curved beams. J. Aerosp. Sci. 25, 627–630 (1958)
Mohammadi, M., Dryden, J.R.: Thermal stress in a nonhomogeneous curved beam. J. Therm. Stress. 31, 587–598 (2008)
Librescu, L., Nemeth, M.P., Starnes, J.H., Lin, W. Jr.: Nonlinear response of flat and curved panels subjected to thermomechanical loads. J. Therm. Stress. 23, 549–582 (2000)
Duc, N.D., Tung, H.V.: Nonlinear response of pressure-loaded functionally graded cylindrical panels with temperature effects. Compos. Struct. 92, 1664–1672 (2010)
Kiani, Y., Shakeri, M., Eslami, M.R.: Thermoelastic free vibration and dynamic behaviour of an FGM doubly curved panel via the analytical hybrid Laplace-Fourier transformation. Acta Mech. 223, 1199–1218 (2012)
Arslan, E., Mack, W., Gamer, U.: Elastic limits of a radially heated thick-walled cylindrically curved panel. Forsch. Ing. 77, 13–23 (2013)
Arslan, E., Mack, W.: Elastic–plastic states of a radially heated thick-walled cylindrically curved panel. Forsch. Ing. 78, 1–11 (2014)
Carslaw H.S., Jaeger J.C.: Conduction of Heat in Solids, 2nd edn. Clarendon, Oxford (1959)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Arslan, E., Haskul, M. Generalized plane strain solution of a thick-walled cylindrical panel subjected to radial heating. Acta Mech 226, 1213–1225 (2015). https://doi.org/10.1007/s00707-014-1248-4
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00707-014-1248-4