Skip to main content

Advertisement

SpringerLink
Log in

Modelling and characterization of a robust, low-power and wide-range thermal wind sensor

  • Technical Paper
  • Published:
Microsystem Technologies Aims and scope Submit manuscript

Abstract

In this paper, we present a robust, low-power and wide-range MEMS thermal wind sensor, which is based on a glass reflow process. A general analytical model is first proposed for obtaining the heater’s temperature and the temperature distribution on the sensor surface. Based on this model, the effect of the sensor’s geometry and package on the sensor’s performance is investigated. These results demonstrate how the measurement range and the sensitivity of the sensor can be optimized with a change in structural geometries. Besides, it has shown that the package structure of the sensor is also important for obtaining the required performance. Then, calculated results are validated with 2-D finite element method (FEM) solver CMOSOL. It is found that although there is some deviation between theoretical and simulation results, the model can have good reference value for latter MEMS thermal wind sensor design. Finally, the sensor is characterized in a wind tunnel. At a constant heating power of 14.5 mW, measurement results show that the sensor can detect airflow speeds of up to 33 m/s, with an accuracy better than 0.5 m/s at low speeds and 5% Full-Scale at high speeds. Airflow direction can be determined in a 360° range with an accuracy better than 5°. In addition, the sensor also shows a good repeatability.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15

Similar content being viewed by others

References

  • Adamec RJ, Thiel DV (2010) Self heated thermo-resistive element hot wire anemometer. IEEE Sens J 10(4):847–848

    Article  Google Scholar 

  • Arritt RW, Clark CA, Goggi AS, Sanchez HL, Westgate ME, Riese JM (2007) Lagrangian numerical simulations of canopy air flow effects on maize pollen dispersal. Field Crops Res 102(2):151–162

    Article  Google Scholar 

  • Aylor DE (1990) The role of intermittent wind in the dispersal of fungal pathogens. Annu Rev Phytopathol 28:73–92

    Article  Google Scholar 

  • Baltes H, Paul O, Brand O (1998) Micromachined thermally based CMOS microsensors. Proc IEEE 86(8):1660–1678

    Article  Google Scholar 

  • Bruschi P, Dei M, Piotto M (2009) A low-power 2-D wind sensor based on integrated flow meters. IEEE Sens J 9(12):1688–1696

    Article  Google Scholar 

  • Chen J, Liu C (2003) Development and characterization of surface micromachined out-of-plane hot-wire anemometer. J Microelectromech Sys 12(6):979–988

    Article  Google Scholar 

  • Comsol (2016) FEA Commercial Software, Burlington, 1997–2016. http://www.comsol.com

  • Connell JR (1982) The spectrum of wind speed fluctuations encountered by a rotating blade of a wind energy conversion system. Sol Energy 29(5):363–375

    Article  Google Scholar 

  • Cubukcu AS, Zernickel E, Buerklin U, Urban GA (2010) A 2D thermal flow sensor with sub-mW power consumption. Sens Actuators A 163(2):449–456

    Article  Google Scholar 

  • Dominguez M, Jiménez V, Ricart J, Kowalski L, Torres J, Navarro S, Castañer L (2008) A hot film anemometer for the Martian atmosphere. Planet Space Sci 56(8):1169–1179

    Article  Google Scholar 

  • Ebefors T, Kälvesten E, Stemme G (1998) Three dimensional silicon triple-hot-wire anemometer based on polyimide joints. In: Proceedings of IEEE. Eleventh annual international workshop on micro electro mechanical systems. An investigation of micro structures, Heidelberg, pp 93–98

  • Gao F, Wang L, Tang L, Zhu C (2005) A novel nano-sensor based on rhodamine-β—isothiocyanate-doped silica nanoparticle for pH measurement. Microchim Acta 152(1–2):131–135

    Article  Google Scholar 

  • Harman GG (1993) Reliability and yield problems of wire bonding in microelectronics. International Society for Hybrid Microelectronics, New York

    Google Scholar 

  • Kaltsas G, Nassiopoulos A, Nassiopoulou AG (2002) Characterization of a silicon thermal gas-flow sensor with porous silicon thermal isolation. IEEE Sens J 2(5):463–475

    Article  Google Scholar 

  • Kim S, Kim S, Kim Y, Park S (2003) A circular-type thermal flow direction sensor free from temperature compensation. Sens Actuators A 108(1):64–68

    Article  Google Scholar 

  • Kumar P, Fennell P, Britter R (2008) Effect of wind direction and speed on the dispersion of nucleation and accumulation mode particles in an urban street canyon. Sci Total Environ 402(1):82–94

    Article  Google Scholar 

  • Lammerink TS, Tas NR, Elwenspoek M, Fluitman JH (1993) Micro-liquid flow sensor. Sens Actuators A 37:45–50

    Article  Google Scholar 

  • Li YB, Jiang ZB (2008) An overview of reliability and failure mode analysis of microelectro-mechanical systems (MEMS). Handbook of Performability Engineering, London, pp 953–966

    Google Scholar 

  • Liu S, Pan S, Xue F, Nay L, Miao JM, Norford LK (2015) Optimization of hot-wire airflow sensors on an out-of-plane glass bubble for 2-D detection. J Microelectromech Syst 24(4):940–948

    Article  Google Scholar 

  • Nguyen NT (1997) Micromachined flow sensors—a review. Flow Meas Instrum 8(1):7–16

    Article  MathSciNet  Google Scholar 

  • Nguyen NT, Dötzel W (1997) Asymmetrical locations of heaters and sensors relative to each other using heater arrays: a novel method for designing multi-range electrocaloric mass-flow sensors. Sens Actuators A 62(1):506–512

    Article  Google Scholar 

  • Sabaté N, Santander J, Fonseca L, Gràcia I, Cané C (2004) Multi-range silicon micromachined flow sensor. Sens Actuators A 110(1):282–288

    Article  Google Scholar 

  • Sadeghi MM, Peterson RL, Najafi K (2013) Air flow sensing using micro-wire-bonded hair-like hot-wire anemometry. J Micromech Microeng 23:085017

    Article  Google Scholar 

  • Shen GP, Qin M, Huang QA (2010) A cross-type thermal wind sensor with self-testing function. IEEE Sens J 10(2):340–346

    Article  Google Scholar 

  • Vilares R, Hunter C, Ugarte I, Aranburu I, Berganzo J, Elizalde J, Fernandez LJ (2010) Fabrication and testing of a SU-8 thermal flow sensor. Sens Actuators B 147(2):411–417

    Article  Google Scholar 

  • Zhao R, Sun S, Ding R (2004) Conditioning strategies of indoor thermal environment in warm climates. Energy Build 36(12):1281–1286

    Article  Google Scholar 

  • Zhu YQ, Chen B, Qin M, Huang QA (2014) 2-D micromachined thermal wind sensors—a review. IEEE Internet Things J 1(3):216–232

    Article  Google Scholar 

  • Zhu YQ, Chen B, Qin M, Huang JQ, Huang QA (2015) Development of a self-packaged 2D MEMS thermal wind sensor for low power applications. J Micromech Microeng 25(8):085011

    Article  Google Scholar 

  • Zhu YQ, Chen B, Gao D, Qin M, Huang QA, Huang JQ (2016) A robust and low-power 2-D thermal wind sensor based on a glass-in-silicon reflow process. Microsyst Technol 22(1):151–162

    Article  Google Scholar 

Download references

Acknowledgements

The project is supported partly by the High-Tech Research and Development of China under Grant 2013AA041106 and partly by the Innovation Project for Graduate Student of Jiangsu Province under Grant KYLX15_0099.

Author information

Authors and Affiliations

  1. Key Laboratory of MEMS of Ministry of Education, Southeast University, Nanjing, 210096, China

    Yanqing Zhu, Ming Qin, Yizhou Ye, Zhenxiang Yi & Qing-an Huang

  2. Foshan Chuandong Magnetic Electronics Co., Ltd, Foshan, 528513, China

    Kewen Long

Authors
  1. Yanqing Zhu
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Ming Qin
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Yizhou Ye
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Zhenxiang Yi
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Kewen Long
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Qing-an Huang
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Ming Qin.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Zhu, Y., Qin, M., Ye, Y. et al. Modelling and characterization of a robust, low-power and wide-range thermal wind sensor. Microsyst Technol 23, 5571–5585 (2017). https://doi.org/10.1007/s00542-017-3361-5

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00542-017-3361-5

Keywords

Search

Navigation