Abstract
Fiber reinforced thermoplastic (FRTP) is a promising material for automobiles, airplanes, construction, home appliances and so on. In situ polymerized polyamide (PA6) is a representative polymer material for FRTP. When ϵ-caprolactam (ϵ-CL) is polymerized in situ, the polymerization of ϵ-CL and crystallization of PA6 occur simultaneously. The polymerization temperature is far below the melting temperature of PA6, and the obtained crystallinity and mechanical strength are far below those of a part prepared by injection molding. Thermal annealing is a practical approach to improve the crystallinity and mechanical properties. However, the effect of thermal annealing on the crystallinity and mechanical properties of FRTPs is still unclear. This study investigated the effect of thermal annealing on the crystallinity and mechanical properties of PA6, textile glass fiber reinforced PA6 (GF-PA6), and carbon fiber reinforced PA6 (CF-PA6) (40 vol%). The specimens were prepared by resin transfer molding with in situ polymerization of ϵ-CL. PA6 was polymerized in situ in a mold with and without fibers. The results indicated that the crystallinity, tensile modulus, and strength of PA6 were improved by thermal annealing. The crystallinity of GF-PA6 was not improved, but the tensile modulus and strength were slightly improved. The crystallinity of CF-PA6 decreased, but the tensile modulus and strength improved. The crystallinity showed a negative correlation to the tensile modulus and strength. Because the tensile modulus and strength of glass and carbon fibers are much higher than those of the crystalline phase of PA6, increasing the crystallinity had a limited effect.
Similar content being viewed by others
References
Ben G, Hirabayashi A, Sakata K, Nakamura K, Hirayama N (2015) Evaluation of new GFRTP and CFRTP using epsilon caprolactam as matrix fabricated with VaRTM. Sci Eng Compos Mater 22:633–641
Blaine RL (2002) thermal applications note polymer heats of fusion. TN048, TA Instruments
Brandrup J, Immergut EH, Grulke EA (2003) Polymer handbook, 4th edn. Wiley, Amsterdam
Castro JM, Macosko CW (1980) SPE Technical Papers 26:434
Durin A, Boyard N, Bailleul JL, Billon N, Chenot JL, Haudin JM (2017) Semianalytical models to predict the crystallization kinetics of thermoplastic fibrous composites. J Appl Polym Sci 134:44508
Haspel B, Hoffmann C, Elsner P, Weidenmann KA (2015) Characterization of the interfacial shear strength of glass-fiber reinforced polymers made from novel RTM processes. Int J Plast Technol 19:333–346
Ito H, Tsutsumi Y, Minagawa K, Takimoto J, Koyama K (1995) Simulations of polymer crystallization under high pressure. Colloid Polym Sci 273:811–815
Kamal MR, Ryan ME (1980) The behavior of thermosetting compounds in injection molding cavities. Polym Eng Sci 20:859–867
Li H, Wang Y, Zhang C, Zhang B (2016) Effects of thermal histories on interfacial properties of carbon fiber/polyamide 6 composites: thickness, modulus, adhesion and shear strength. Compos Part A Appl Sci Manuf 85:31–39
Pillay S, Vaidya UK, Janowski GM (2005) Liquid molding of carbon fabric-reinforced nylon matrix composite laminates. J Thermoplast Compos Mater 18:509–527
Shojaei A, Ghaffarian SR, Karimian SMH (2003) Modeling and simulation approaches in the resin transfer molding process: a review. Polym Compos 24:525–544
Taki K, Shoji N, Kobayashi M, Ito H (2016) A kinetic model of viscosity development for in situ ring-opening anionic polymerization of ϵ-caprolactam. Microsyst Technol pp 1–9
van Rijswijk K, Bersee HEN (2007) Reactive processing of textile fiber-reinforced thermoplastic composites: an overview. Compos. Part A Appl Sci Manuf 38:666–681
Yan X, Imai Y, Shimamoto D, Hotta Y (2014) Relationship study between crystal structure and thermal/mechanical properties of polyamide 6 reinforced and unreinforced by carbon fiber from macro and local view. Polymer 55:6186–6194
Zheng LY, Wang YL, Wan YZ, Zhou FG, Dong XH (2002) Preparation and properties of in situ polymerized fiber-reinforced nylon composites. J Mater Sci Lett 21:987–989
Author information
Authors and Affiliations
Corresponding authors
Rights and permissions
About this article
Cite this article
Taki, K., Suenaga, H. & Ito, H. Effect of thermal annealing on crystallinity and mechanical strength of textile glass and carbon fiber reinforced in situ polymerized ϵ-caprolactam parts. Microsyst Technol 24, 663–668 (2018). https://doi.org/10.1007/s00542-017-3317-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00542-017-3317-9