Skip to main content
Log in

Influence of design and fabrication on RF performance of capacitive RF MEMS switches

  • Technical Paper
  • Published:
Microsystem Technologies Aims and scope Submit manuscript

Abstract

Shunt capacitive radio-frequency microelectromechanical system (RF MEMS) switches were fabricated on silicon substrate and characterized in the RF domain. Various switch typologies were obtained by three different approaches, which are: (1) the change of the bridge geometric parameters, (2) the covering of the actuator with a floating metal, and (3) the deposition of the bridge directly on the actuator. The S parameters of the fabricated switches were measured in the up and down states, observing the impact on the RF performance of the variation of the geometric parameters and the fabrication process. The electromagnetic modelling of the fabricated switches was used to interpret the measured RF behaviour, allowing to elucidate the drawbacks of the non-perfect conforming of the bridge on the actuator. Finally, the reliability of the fabricated RF MEMS switches under a bipolar voltage excitation was evaluated by cycling tests. Hence, the study presented here provides guidelines to solve some issues of the tight correlation between design, fabrication, performance, and reliability of RF MEMS switches, in view of a large-scale development of these devices.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Subscribe and save

Springer+ Basic
EUR 32.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or Ebook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Fig. 1
Fig. 2
Fig. 3
Fig. 4

Similar content being viewed by others

References

  • Bansal D, Kumar A, Sharma A, Kumar P, Rangra KJ (2014) Design of novel compact anti-stiction and low insertion loss RF MEMS switch. Microsyst Technol 20:337–340

    Article  Google Scholar 

  • Bartolucci G, Marcelli R, Catoni S, Margesin B, Giacomozzi F, Mulloni V, Farinelli P (2008) An equivalent-circuit model for shunt-connected coplanar microelectromechanical system switches for high frequency applications. J Appl Physics 104:084514-1–084514-8

    Article  Google Scholar 

  • Calaza C, Margesin B, Giacomozzi F, Rangra K, Mulloni V (2007) Electromechanical characterization of low actuation voltage RF MEMS capacitive switches based on DC CV measurements. Microelectr Eng 84:1358–1362

    Article  Google Scholar 

  • Chu C-H, Shih W-P, Chung S-Y, Tsai H-C, Shing T-K, Chang P-Z (2007) A low actuation voltage electrostatic actuator for RF MEMS switch applications. J Micromech Microeng 17:1649–1656

    Article  Google Scholar 

  • Giacomozzi F, Calaza C, Colpo S, Mulloni V, Collini A, Margesin B, Farinelli P, Casini F, Marcelli R, Mannocchi G, Vietzorreck L (2008) Development of high con coff ratio RF MEMS shunt switches. Romanian J Inform Sci Techn 11(2):143–151

    Google Scholar 

  • Iannacci J (2015) Reliability of MEMS: a perspective on failure mechanisms, improvement solutions and best practices at development level. Displays 37:62–71

    Article  Google Scholar 

  • Kim J, Kwon S, Jeong H, Hong Y, Lee S, Song I, Ju B (2009) A stiff and flat membrane operated DC contact type RF MEMS switch with low actuation voltage. Sens Actuators A 153:114–119

    Article  Google Scholar 

  • Marcelli R, Bartolucci G, Minucci G, Margesin B, Giacomozzi F, Vitulli F (2004) Lumped element modelling of coplanar series RF MEMS switches. Electron Lett 40(20):1272–1274

    Article  Google Scholar 

  • Marcelli R, Papaioannu G, Catoni S, De Angelis G, Lucibello A, Proietti E, Margesin B, Giacomozzi F, Deborgies F (2009) Dielectric charging in microwave microelectromechanical Ohmic series and capacitive shunt switches. J Appl Phys 105:114514-1–114514-10

    Article  Google Scholar 

  • Mulloni V, Giacomozzi F, Margesin B (2010) Controlling stress and stress gradient during the release process in gold suspended micro-structures. Sens Actuators A 162:93–99

    Article  Google Scholar 

  • Peroulis D, Pacheco SP, Sarabandi K, Katehi LPB (2003) Electromechanical considerations in developing low-voltage RF MEMS switches. IEEE Trans Microw Theory Tech 51(1):259–270

    Article  Google Scholar 

  • Peroulis D, Pacheco SP, Sarabandi K, Katehi LPB (2004) RF MEMS switches with enhanced power-handling capabilities. IEEE Trans Microw Theory Tech 52(1):59–68

    Article  Google Scholar 

  • Persano A, Cola A, De Angelis G, Taurino A, Siciliano P, Quaranta F (2011) Capacitive RF MEMS switches with tantalum-based materials. J Micrelectrom Syst 20(2):365–370

    Article  Google Scholar 

  • Persano A, Tazzoli A, Cola A, Siciliano P, Meneghesso G, Quaranta F (2012a) Reliability enhancement by suitable actuation waveforms for capacitive RF MEMS switches in III–V technology. J Micrelectrom Syst 21(2):414–419

    Article  Google Scholar 

  • Persano A, Tazzoli A, Farinelli P, Meneghesso G, Siciliano P, Quaranta F (2012b) K-band capacitive MEMS switches on GaAs substrate: design, fabrication, and reliability. Microelectr Reliab 52:2245–2249

    Article  Google Scholar 

  • Persano A, Quaranta F, Martucci MC, Siciliano P, Cola A (2015) On the electrostatic actuation of capacitive RF MEMS switches on GaAs substrate. Sens Actuators A 232:202–207

    Article  Google Scholar 

  • Philippine MA, Zareie H, Sigmund O, Rebeiz GM, Kenny TW (2013) Experimental validation of topology optimization for RF MEMS capacitive switch design. J Micrelectrom Syst 22(6):1296–1309

    Article  Google Scholar 

  • Rebeiz G (2003) RF MEMS Theory, Design, and Technology. Wiley-Interscience, New York

    Google Scholar 

  • Rezvanian O, Zikry MA, Brown C, Krim J (2007) Surface roughness, asperity contact and gold RFMEMS switch behavior. J Micromech Microeng 17:2006–2015

    Article  Google Scholar 

  • van Spengen WM (2012) Capacitive RF MEMS switch dielectric charging and reliability: a critical review with recommendations. J Micromech Microeng 22(7):074001-1–074001-23

    Google Scholar 

  • Yu AB, Liu AQ, Zhang QX, Hosseini HM (2006) Effects of surface roughness on electromagnetic characteristics of capacitive switches. J Micromech Microeng 16:2157–2166

    Article  Google Scholar 

Download references

Acknowledgments

This work has been partially supported by MIUR under Project 02876 “TASMA” of the National Operative Program (PON).

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Anna Persano.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Persano, A., Quaranta, F., Capoccia, G. et al. Influence of design and fabrication on RF performance of capacitive RF MEMS switches. Microsyst Technol 22, 1741–1746 (2016). https://doi.org/10.1007/s00542-016-2829-z

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00542-016-2829-z

Keywords

Navigation