Abstract
In this work, amplification units made of robust metallic nickel titanium (NiTi) and single crystal silicon are compared and evaluated for the application in miniaturized piezoelectric actuators for flow control purposes. The amplification mechanism with a sliced membrane structure is based on a mechanical lever in order to amplify the low piezoelectrically induced deformation. Therefore, an enhanced output stroke can be provided up to high frequencies. The different membrane fabrication processes using laser ablation for the NiTi alloy and deep reactive ion etching for the silicon substrate, as well as the results of finite element simulations and experimental measurements are reported. An amplification factor of 9 has been achieved for an optimized load transmission point position. The dynamic response shows a quality factor of 25 and 494 at the first fundamental mode for NiTi and silicon membranes, respectively. Compared to silicon, NiTi shows enhanced properties against failure and facilitates the integration process.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
ANSYS 10.0 Documentation (2005) ANSYS Inc. Canonsburg, PA
Anzinger C, Schmid U, Krötz G (2002) Fast responding automotive microinjector operating with a multiplated piezoelectric actuator 8th International conference on new actuators. Bremen, Germany, pp 130–133
Bolzmacher C, Bauer K, Hafez M, Schmid U, Seidel H (2008) Piezoelectric microactuator with mechanically amplified leverage unit. 22nd European conference on solid-state sensors, Dresden, Germany, Sept 7–10, pp 895–898
Bolzmacher C, Bauer K, Schmid U, Hafez M, Seidel H (2009) Robust superelastic, metallic amplification unit for piezoelectric microactuators. Proc. of the SPIE 7362:73620M–73620M-8
Buehler WJ, Wang FE (1967) A summary of recent research on the Nitinol alloys and their potential application in ocean engineering. Ocean Eng 1:105–120
Engert M, Pätzold A, Becker R, Nitsche W (2006) Active cancellation of Tollmien-Schlichting instabilities in compressible flows using closed-loop control. IUTAM symposium on flow control and MEMS, pp 319–331
Ho CM, Tung S, Lee GB, Tai YC, Jiang F, Tsao T (1997) MEMS—a technology for advancements in aerospace engineering. 35th Aerospace Science Meeting & Exhibit. Reno, NV, pp 1–10
Liu HK, Pan CH, Liu PP (2008) Dimension effect on mechanical behaviour of silicon micro-cantilever beams. J Meas 41:885–895
Niezrecki C, Brei D, Balakrishnan S, Moskalik A (2001) Piezoelectric actuation: state of the art. Shock Vib Dig 33(4):269–280
Pérez R, Gumbsch P (2000) Directional anisotropy in the cleavage fracture of silicon. Phys Rev Lett 84(23):5347–5350
Petersen KE (1982) Silicon as a mechanical material. Proc of IEEE 70(5):420–457
Shimizu K, Tadaki T (1987) Shape memory effect: mechanism. In: Shape memory alloys, Gordon and Breach Science, New York, pp 1–60
Acknowledgments
The work reported here was performed as part of the AVERT project [Contract No RTD REG/H.3(2006)A/142121] and is funded by the European Union.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Bolzmacher, C., Bauer, K., Schmid, U. et al. Robust miniaturized amplification unit for piezoelectric actuators: comparison of single crystal silicon and superelastic nickel titanium as membrane materials. Microsyst Technol 16, 847–853 (2010). https://doi.org/10.1007/s00542-009-1008-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00542-009-1008-x