Abstract
In microsystems technology, passivation layers are generally required to protect micro devices and functional elements against environmental impact, particularly against corrosion, thus increasing reliability and lifetime to acceptable values. In this work, the use of sputter-deposited aluminium oxide and aluminium nitride thin films on flexible polyimide foils was investigated, aiming at the protection of flow sensitive elements. Due to a high defect density located at the interface between the passivation layer and the organic substrate, the adhesion of pure aluminium oxide thin films was found to be poor when applying a combination of mechanical stress (e.g. bombardment with water droplets) and thermal cycling as an accelerated ageing procedure. A bi-layer consisting of aluminium nitride and aluminium oxide, however, shows a defect-free interface to the organic substrate resulting in an enhanced adhesion. In addition, no structural failure can be detected after applying the aging procedure, making this bi-layer approach well suited for the targeted application.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Abad E, Raffa VS, Mazzolai B, Marco S, Krenkow A, Becker T (2005) Development of a flexible tag microlab. In: Proceedings of SPIE—the international society for optical engineering, vol 5836. p 599
Abad E, Mazzolai B, Juarros A, Gómez D, Mondini A, Sayhan I, Krenkow A, Becker T (2007) Fabrication process for a flexible tag microlab. In: SPIE-conference “Microtechnologies for the New Millenium”, vol. 6589, pp 65890U, 2.5–4.5, Gran Canaria
Bagolini A, Pakula L, Scholtes M, Pham M, French PJ, Sarro PM (2002) Polyimide sacrificial layer and novel materials for post-processing surface micromachining. J Micromech Microeng 12:385
Brandon E, West W, Zhou L, Jackson T, Theriot G, Devine R, Binkley D, Verma N, Crawford R (2004) Flexible electronics for space applications. Mater Res Soc Symp Proc 814:I9.7.1
Buder U, von Klitzing JP, Obermeier E (2006) Reactive ion etching for bulk structuring of polyimide. Sens Actuators A 132:393
Carcia PF, McLean RS, Reilly MH, Malajovich I, Sharp KG, Agrawal S, Nunes G Jr (2003) ZnO thin film transistors for flexible electronics. Mater Res Soc Symp Proc 769:H7.2.1
Carcia PF, McLean RS, Reilly MH (2005) Oxide engineering of ZnO thin-film transistors for flexible electronics. J Soc Inf Disp 13:547
Carlson JA, English JM, DJ Coe (2006) A flexible, self-healing sensor skin. Smart Mater Struct 15:N129
Chai J, Li B, Kwok DY (2005) Selective surface modification and patterning by a micro-plasma discharge. Appl Phys Let 86:34107
Hausmann F, Schröder W (2004) Transition detection in cruise flight using a resistant multi-sensor hot-film technique. In: Proceedings of the 42nd AIAA aerospace science meeting and exhibit, AIAA 2004-1047, Reno, Nevada
Hausmann F, Schröder W, Limberg W (2002) Development of a multi-sensor hot-film measuring technique for transition detection in cruise flight. AIAA Paper: 2002-0534
Jia Y, Sun K, Agosto FJ, Quinones MT (2006) Design and characterization of a passive wireless strain sensor. Meas Sci Technol 17:2869
Kim D, Lee CC (2006) Fluxless flip-chip Sn-Au solder interconnect on thin Si wafers and Cu laminated polyimide films. Mat Sci Eng A 416:74
Kinloch AJ, Yuen ML (1989a) The mechanical behaviour of polyimide copper laminates. Part 1: Locus of failure studies. J Mater Sci 24:2183
Kinloch AJ, Yuen ML (1989b) The mechanical behaviour of polyimide copper laminates. Part 2: Peel energy measurements. J Adhes 30:151
Ngo L, Kupke W, Seidel H, Schmid U (2004) Simulation and experimental results of a hot-film anemometer array on a flexible substrate. In: Proceedings micro–nano technologies for aerospace applications (CANEUS 2004), AIAA 2004-6726
Schmid U, Ababneh A, Seidel H, Wagner R, Bauer K (2007) Investigations on the passivation of thin film flow sensors on flexible substrates. In: SPIE-conference “Microtechnologies for the New Millenium”, vol. 6589, pp 65890H, 2.5–4.5, Gran Canaria
Thornton JA, Chin J (1977) Structure and heat treatment characteristics of sputter-deposited alumina. Ceram Bul 56:504
Turban G, Rapeaux M (1983) Dry etching of polyimide in O2–CF4 and O2–SF6 plasmas. J Electrochem Soc 130:2231
Zweifel H (2001) Plastics additives handbook, 5th edn. Hanser Fachbuchverlag
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Schmid, U., Ababneh, A., Seidel, H. et al. Characterization of aluminium nitride and aluminium oxide thin films sputter-deposited on organic substrates. Microsyst Technol 14, 483–490 (2008). https://doi.org/10.1007/s00542-007-0434-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00542-007-0434-x