Summary
UHF RFID tags have demonstrated considerable degradation of performance when being attached to products. Absorption, reflection, detuning, and other RF effects decrease the sensitivity of the tags. We are presenting an UHF RFID measurement and performance evaluation test system, which allows for evaluations of designs of labels and ICs. Furthermore, it provides means for quantifying tag performance in various applications through measurements and tests.
Zusammenfassung
UHF RFID Tags zeigen eine beachtliche Verschlechterung der Leistung, sobald sie an Objekten angebracht werden. Absorption, Reflexion, Verstimmung und andere RF-Effekte vermindern die Transponder-Sensitivität. Es wird ein UHF RFID-Mess- und Leistungsevaluationstestsystem vorgestellt, welches bei der Evaluierung von Labeldesigns und ICs zur Anwendung kommt.
Similar content being viewed by others
References
Derbek, V. (2007): A model-based methodology for real-time verification and optimization of UHF RFID systems. PhD thesis, Graz University of Technology.
Derbek, V., Steger, C., Kajtazovic, S., Preishuber-Pfluegl, J., Pistauer, M. (2005): Behavioral model of UHF RFID tag for system and application level simulation. Proc. of IEEE Int. Behavioral Modeling and Simulation Workshop (BMAS).
Derbek, V., Wischounig, D., Steger, C., Preishuber-Pfluegl, J., Pistauer, M. (2007): Simulation platform for UHF RFID. Proc. of IEEE Conf. on Design automation and Test in Europe (DATE).
EPCglobal EPC™ Radio-Frequency Identity Protocols Class 1 Generation 2 UHF RFID Tag Performance.
EPCglobal EPC™ Radio-Frequency Identity Protocols Class 1 Generation 2 UHF RFID Protocol for Communications at 860–960 MHz.
European EPC Competence Center (2007): The UHF Tag Performance Survery.
ISO/IEC 18000-6: Information technology automatic identification and data capture techniques – Radio frequency identification for item management – Part 6: Parameters for air interface communications at 860 MHz to 960 MHz.
ISO/IEC 18046-3: Information technology – Radio frequency identification device performance test methods – Part 3: Test methods for tag performance.
ISO/IEC 18047-6: Information technology, automatic identification and data capture techniques – RFID device conformance test methods – Part 6: Test methods for air interface communication at 860–960 MHz.
Karthaus, U., Fischer, M. (2003): Fully integrated passive UHF RFID transponder IC with 16.7-μ W minimum RF input power. IEEE Journal of Solid-State Circuits.
Lam, S. F., Nikitin, P. V., Rao, K. V. S. (2005): Antenna design for UHF RFID tags: a review and a practical application., IEEE Transactions on Antennas and Propagation, 53.
Murfett, D. (2004): The challenge of testing RFID integrated circuits. 2nd IEEE Int. Workshop on Electronic Design, Test and Applications, 2004. DELTA 2004.
National Instruments: PCI eXtensions for Instrumentation.
Puleston, D. J., Forster, I. J. (2005): The test pyramid: a framework for consistent evaluation of RFID tags from design and manufacture to end use. Whitepaper, Avery Dennison RFID Division.
PXI System Alliance: PXI hardware specification.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Derbek, V., Steger, C., Weiss, R. et al. A UHF RFID measurement and evaluation test system. Elektrotech. Inftech. 124, 384–390 (2007). https://doi.org/10.1007/s00502-007-0482-z
Received:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/s00502-007-0482-z