Abstract
The main objective of this paper is to help the orthopaedic in selecting the most suitable artificial intervertebral disc material that can be used in intervertebral disc replacement surgery based on the finite element method. The study uses a three-dimensional model for the lumber 4–lumber 5 spine vertebras for real patient DICOM dataset and saves as stereolithography format. The stereolithography file for the vertebras is converted into a computer-aided diagnostic file to be suitably imported in SolidWorks software. The integrated three-dimensional model assembles and boundary conditions are applied to the model, including axial force applied on the lumber 4–lumber 5 spine. The disc is designed and constructed using SolidWorks, and then four materials are applied to the artificial intervertebral disc. The results show that cobalt–chromium material is the most suitable material to be used in artificial spinal disc according to the maximum stress under an axial compression force of 300 N for cobalt–chromium and titanium was 109,308,136 N/m2 and 95,111,200 N/m2, while the maximum stress under an axial extension for cobalt–chromium and titanium was 109,308,136 N/m2 and 95,111,184 N/m2. The maximum stress under a right-side bending for cobalt–chromium and titanium was 30,456,905,728 N/m2 and 29,162,355,200 N/m2, and the maximum stress under a right-side bending for cobalt–chromium and titanium was 34,716,794,880 N/m2 and 33,086,228,480 N/m2.
Similar content being viewed by others
References
Agarwal G, Robertson MA, Sonar H, Paik J (2017) Design and computational modeling of a modular, compliant robotic assembly for human lumbar unit and spinal cord assistance. Sci Rep 7:14391–14402
Akbarian D, Rouhi G, Mosavi Mashhadi M et al (2015) Biomechanics of cervical spine following implantation of a semi-constrained artificial disc with upward center of rotation: a finite element investigation. J Mech Med Biol 15(04):1550063
Bruin F, Ter Horst S, van den Berg R, de Hooge M, van Gaalen F, Fagerli KM, Landewe R, van Oosterhout M, Bloem JL, van der Heijde D, Reijnierse M (2016) Signal intensity loss of the intervertebral discs in the cervical spine of young patients on fluid-sensitive sequences. Skelet Radio 45(3):375–381
Chama A, Gerber S, Wang RJ (2018) Newton–raphson solver for finite element methods featuring nonlinear hysteresis model. IEEE Trans Magn 54(1):1–8
Clouthier AL, Hosseini HS, Maquer G, Zysset PK (2015) Finite element analysis predicts experimental failure patterns in vertebral bodies loaded via intervertebral discs up to large deformation. Med Eng Phys 37(6):599–604
Cobetto N, Aubin CE, Parent S, Clin J, Barchi S, Turgeon I et al (2017) Effectiveness of braces designed using computer-aided design and manufacturing (CAD/CAM) and finite element simulation compared to CAD/CAM only for the conservative treatment of adolescent idiopathic scoliosis: a prospective randomized controlled trial. Eur Spine J 12:1–8
Dreischarf M, Shirazi-Adl A, Arjmand N, Rohlmann A, Schmidt H (2016) Estimation of loads on human lumbar spine: a review of in vivo and computational model studies. J Biomech 49(6):833–845
Du T, Chen J, Lan F (2016) Analysis of liver impact responses through a Chinese human body finite element model. J Mech Med Biol 16(08):1640024
Fu C, Peng X, Kai Z et al (2015) Three-dimensional finite element analysis of lumbar interbody fusion with intervertebral foramen. J Shanghai Jiaotong Univ 49(12):300–306
Gempp E, Louge P, de Maistre S (2016) Predictive factors of dysbaric osteonecrosis following musculoskeletal decompression sickness in recreational SCUBA divers. Jt Bone Spine 83:357–358
Gloria A, De Santis R, Ambrosio L, Causa F, Tanner KE (2011) A multi-component fiber-reinforced PHEMA-based hydrogel/HAPEXTM device for customized intervertebral disc prosthesis. J Biomater Appl 25(8):795–810
Hui Yu, Jun-Sheng W, Bin Yu, Zhang C, Jing D (2018) Construction of biological model of human lumbar and analysis of its mechanical properties. Int J Pattern Recognit Artif Intell 32(5):1–27
Islam MT, Chaudhry A, Tang S, Tasciotti E, Righetti R (2018) A new method for estimating the effective Poisson’s ratio in ultrasound poroelastography. IEEE Trans Med Imaging 37(5):1178–1191
Jackman TM, Hussein AI, Curtiss C, Fein PM, Camp A, De Barros L, Morgan EF (2016) Quantitative 3-D visualization of the initiation and progression of vertebral fractures under compression and anterior flexion. J Bone Miner Res 31:777–788
Lehmann T, Rossa C, Usmani N, Sloboda RS, Tavakoli M (2018) Intraoperative tissue young’s modulus identification during needle insertion using a laterally actuated needle. IEEE Trans Instrum Meas 67(2):371–381
Liu F, Wei W, Yang G et al (2017) Therapeutic effects and finite element analysis of a combined treatment using laser needle-knife with supine repositioning massage on patients with cervical spondylotic vertebral arteriopathy. Int J Pattern Recogn Artif Intell 31(11):1757008
Mahdy LN, Ezzat KA, Hassanien AE (2018) Automatic detection system for degenerative disk and simulation for artificial disc replacement surgery in the spine. ISA Trans. https://doi.org/10.1016/j.isatra.2018.07.006
Maquer G, Schwiedrzik J, Huber G, Morlock MM, Zysset PK (2015) Compressive strength of elderly vertebrae is reduced by disc degeneration and additional flexion. J Mech Behav Biomed Mater 42:54–66
Naserkhaki S (2016) Effects of inter-individual lumbar spine geometry variation on load-sharing: geometrically personalized finite element study. J Biomech 49(13):2909–2917
Naserkhaki S, Jaremko JL, Adeeb S, El-Rich M (2016) On the load-sharing along the ligamentous lumbosacral spine: finite element study. J Biomech 49:974–982
Papazafeiropoulos G, Muniz-Calvente M, Martinez-Paneda E (2017) Abaqus2Matlab: a suitable tool for finite element post-processing. Adv Eng Softw 105:9–16
Park WM, Kim YH, Lee S (2013) Effect of intervertebral disc degeneration on biomechanical behaviors of a lumbar motion segment under physiological loading cases. J Mech Sci Technol 43(9):1234–1240
Peters JR, Campbell RM Jr, Balasubramanian S (2017) Characterization of the age-dependent shape of the pediatric thoracic spine and vertebrae using generalized procrustes analysis. J Biomech 63:32–40
Putzer M, Ehrlich I, Rasmussen J, Gebbeken N, Dendorfer S (2016) Sensitivity of lumbar spine loading to anatomical parameters. J Biomech 49(6):953–958
Qin BL (2014) Determination of trunk muscle forces for flexion and extension by using a validate finite element model of the lumbar spine and measure in vivo data. J Biomech 39(6):981–989
Qing-Hua M, Chun-Yu B (2011) Mechanics analysis of lumbar segment for the athlete during preparing lifting barbell and it is finite element simulation. In: 2011 international conference on future computer science and education. IEEE, vol 1, pp 55–58
Rolvien T, Hahn M (2017) Vertebral bone microarchitecture and osteocyte characteristics of three toothed whale species with varying diving behaviour. Sci Rep 7:1604–1614
Sattout A, Clin J, Cobetto N, Labelle H, Aubin CE (2016) Biomechanical assessment of providence nighttime brace for the treatment of adolescent idiopathic scoliosis. Spine Deform 4(4):253–260
Shahmohammadia M, Shirazia HA, Karimia A, Navidbakhsha M (2014) Finite element simulation of an artificial intervertebral disk using fiber reinforced laminated composite model. Tissue Cell 46:299–303
Shih K-S, Hsu C-C et al (2015) Biomechanical investigation of pedicle screw-based posterior stabilization systems for the treatment of lumbar degenerative disc disease using finite element analyses. Biomed Eng App Basis Commun 27(06):1550060
Vergari C, Courtois I, Ebermeyer E, Bouloussa H, Vialle R, Skalli W (2015) Simulation of orthotic treatment in adolescent idiopathic scoliosis using a subject-specific finite element model. Comput Methods Biomech Biomed Eng 18:2076–2077
Wang Y, Cao L, Bai Z, Reed MP, Rupp JD, Hoff CN, Hu J (2016) A parametric ribcage geometry model accounting for variations among the adult population. J Biomech 49(13):2791–2798
Whittier DE, Manske SL, Kiel DP, Bouxsein M, Boyd SK (2018) Harmonizing finite element modelling for non-invasive strength estimation by high-resolution peripheral quantitative computed tomography. J Biomech 80:63–71
Xu M, Yang J, Lieberman IH, Haddas R (2017) Lumbar spine finite element model for healthy subjects: development and validation. Comput Methods Biomech Biomed Eng PubMed 32(1):151–156
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
All authors have no conflict of interest.
Ethical approval
This article does not contain any studies with human participants or animals performed by any of the authors.
Additional information
Communicated by X. Wang, A. K. Sangaiah, M. Pelillo.
Rights and permissions
About this article
Cite this article
Omran, L.N., Ezzat, K.A., Elhoseny, M. et al. Biomechanics of artificial intervertebral disc with different materials using finite element method. Soft Comput 23, 9215–9236 (2019). https://doi.org/10.1007/s00500-018-3574-2
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00500-018-3574-2