Do patient-specific instruments (PSI) for UKA allow non-expert surgeons to achieve the same saw cut accuracy as expert surgeons?



High-volume unicompartmental knee arthroplasty (UKA) surgeons have lower revision rates, in part due to improved intra-operative component alignment. This study set out to determine whether PSI might allow non-expert surgeons to achieve the same level of accuracy as expert surgeons.

Materials and methods

Thirty-four surgical trainees with no prior experience of UKA, and four high-volume UKA surgeons were asked to perform the tibial saw cuts for a medial UKA in a sawbone model using both conventional and patient-specific instrumentation (PSI) with the aim of achieving a specified pre-operative plan. Half the participants in each group started with conventional instrumentation, and half with PSI. CT scans of the 76 cut sawbones were then segmented and reliably orientated in space, before saw cut position in the sagittal, coronal and axial planes was measured, and compared to the pre-operative plan.


The compound error (absolute error in the coronal, sagittal and axial planes combined) for experts using conventional instruments was significantly less than that of the trainees (11.6°±4.0° v 7.7° ±2.3º, p = 0.029). PSI improved trainee accuracy to the same level as experts using conventional instruments (compound error 5.5° ±3.4º v 7.7° ±2.3º, p = 0.396) and patient-specific instruments (compound error 5.5° ±3.4º v 7.3° ±4.1º, p = 0.3). PSI did not improve the accuracy of high-volume surgeons (p = 0.3).


In a sawbone model, PSI allowed inexperienced surgeons to achieve more accurate saw cuts, equivalent to expert surgeons, and thus has the potential to reduce revision rates. The next test will be to determine whether these results can be replicated in a clinical trial.


Unicompartmental knee arthroplasty (UKA) is an attractive option in patients with mono-compartment gonarthrosis. Compared to total knee arthroplasty (TKA), it is associated with a lower risk profile, shorter length of stay, restoration of a more physiological gait, and higher outcome scores [1,2,3,4]. However, UKA is also associated with higher revision rates, and this may be an important factor in explaining why it accounts for less than 10% of knee replacements in a number of national joint registries [5,6,7].

Lower revision rates for UKA are consistently observed in high-volume surgeons and specialist centres [8,9,10,11]. The aetiology of this caseload effect is likely to be multifactorial. One of these factors is that UKA is a technically demanding procedure with a narrow tolerance for tibial component malpositioning; deviations of more than 3° from the native joint line in the coronal plane and 2° in the sagittal plane are associated with decreased prosthesis survival [12, 13]. In this context, the results of a randomised controlled trial RCT comparing conventional and patient-specific instrumentation for UKA are encouraging [14]. The authors, who are both high-volume UKA surgeons, found no difference in component alignment between the two techniques, suggesting that PSI might be able to replicate expert results [15].

The aim of our sawbone study was to ascertain whether PSI allows inexperienced UKA surgeons to achieve the same level of accuracy as expert surgeons by comparing their ability to achieve a planned medial UKA tibial saw cut in the coronal, sagittal and axial planes.

Materials and methods

Seventy-six identical sawbone tibias, manufactured in the same batch, were used (Sawbones Europe AB, Malmo, Sweden). To create a standard reference, one of these tibias was CT scanned with 1 mm-thick slices and segmented using Mimics software (Materialise NV, Leuven, Belgium) to produce a 3D model. Using 3-matic software (Materialise NV, Leuven, Belgium), this bone model was aligned in 3D space using established frames of reference: the tibial mechanical axis in the Z plane, and the anatomical tibial axis in the X and Y planes [16]. A virtual tibial bone cut for an Oxford medial compartment UKA (Zimmer Biomet, Bridgend, UK) was then planned 4 mm below the joint line, with a coronal varus/valgus angulation of 0°, a posterior slope of 7° (as delivered by conventional instrumentation when the guide shaft is aligned parallel with the tibial long axis [17]), and an axial orientation parallel to the anatomical tibial axis [16] (Fig. 1).

Fig. 1

Planned UKA position

A PSI to deliver this surgical plan through a standard minimally invasive incision was 3D printed in medical grade Nylon (PA 2200) using an EOS P110 (Embody, London, UK) (Fig. 2). The guide was designed to be used in the same manner as the Oxford Phase III conventional instruments (Zimmer Biomet, Bridgend, UK), and the distal portion of the guide manufactured to fit the conventional ankle clamp.

Fig. 2

PSI for UKA saw cuts

A minimum sample size of four surgeons in each group was calculated based on a 5% significance level, a power of 80%, a standard deviation of 1.25 estimated from Ollivier et al.’s RCT [14], and a desire to detect a 3° difference in coronal implant orientation [13, 14]. Four expert UKA surgeons (defined as performing more than 30 cases per year [9]) and 34 surgical trainees (no prior experience of UKA surgery) were recruited. All participants watched a video demonstration of the tibial saw cuts for a medial UKA using both conventional Oxford Phase III (Zimmer Biomet, Bridgend, UK) and PSI instruments (Embody, London, UK).

The simulation model used by the implant manufacturer (Zimmer Biomet, Bridgend, UK) for their instructional courses was replicated in this study, i.e. a sawbone knee joint with three stretch tube ligaments mimicking the LCL, MCL and PCL (Model number 1148-1, Sawbones Europe AB, Malmo, Sweden), held in a holder from the same company, that simulated soft tissue and skin around the tibia and femur, whilst allowing free access to the knee joint in a position encountered in the operating theatre (Model 1506). Each participant was provided with printouts of Fig. 1 and asked to achieve this pre-operative plan twice: once with PSI, and once with conventional instruments. Half the participants started first with PSI, and half with the conventional instruments, before swapping over. Oscillating (12 mm × 90 mm) and reciprocating (70 mm × 10 mm) sawblades (De Soutter Medical, Buckinghamshire, UK) designed for clinical use in UKA were used to perform the cuts.

Each cut tibia was CT scanned (1 mm thick slices) and segmented using Mimics software (Materialise NV, Leuven, Belgium) to produce a 3D model. This was surface matched with the pre-operative 3D bone model to ensure identical orientation in space. Acrobot planning software (Acrobot, UK), validated for clinical use, was then used to position a tibial component onto the cut bone surface, and the varus/valgus, posterior slope, and axial rotation recorded. This process was performed by a blinded independent observer and repeated on a random selection of ten bones 1 week later. A second observer (GGJ) repeated the measurements on the same randomly selected ten bones.

SPSS v22 (IBM Corp, New York, USA) was used for statistical analysis. Paired t tests were used to compare within group differences, and unpaired t tests to compare between groups. A Welch independent t test was used if the homogeneity of variances was found to be unequal. Statistical significance was set at p < 0.05.


The absolute difference between the planned and achieved implant position was considered for all analyses, and is referred to simply as the ‘error’. Coronal, sagittal and axial plane measurements were considered separately, and together as a compound error (Fig. 3). The p values of differences between the groups are displayed in Tables 1 and 2.

Fig. 3

Box plots of the absolute error (degrees) between the planned and achieved implant positions in the coronal, sagittal, and axial planes, plus compound error of all three planes

Table 1 Comparison of mean absolute error in implant position (SD) between experts and trainees using conventional and patient-specific (PSI) instrumentation
Table 2 Comparison of mean absolute error in implant position (SD) using conventional and patient-specific (PSI) instrumentation for trainees and experts

Conventional Instruments

For both groups using conventional instruments, the experts’ mean error was significantly lower than the trainees’ in both the axial and sagittal planes, but interestingly not in the coronal plane (Table 1). The overall compound error was significantly lower for the expert group.


Compared to conventional instruments, PSI significantly reduced the mean error for trainees in all three planes (Table 2). For the expert group, PSI only reduced error in the coronal plane. There was no difference between the trainees and experts using PSI (Table 1).

Trainees with PSI vs. experts with conventional instruments

Compared to experts using conventional instruments, trainees with PSI had a significantly lower mean error in the coronal plane, and comparable mean error in the sagittal and axial planes (Table 1). There was no difference in the overall compound error between trainees using PSI and experts using conventional instrumentation.

Measurement reliability

The mean inter-rater measurement error was 0.3° (sd 0.3°) coronal plane, 0.4° (sd 0.3°) sagittal plane, and 0.4° (sd 0.4°) axial plane. The mean intra-rater error was 0.3° (sd 0.3°), 0.4° (sd 0.3°), and 0.5° (sd 0.4°) respectively. Inter-rater (3,1) and intra-rater (1,1) intra-class correlation coefficients in all three planes indicated almost perfect agreement using the Landis and Koch criteria [18].


This study addressed one of the factors in the low uptake of UKA surgery, despite its many advantages to patients. Given the high degree of technical expertise required, we set out to determine whether assistive technology, in the form of low-cost 3D printed instruments, has the potential to improve surgical accuracy in low-volume surgeons.

Unsurprisingly, this study shows that overall, using conventional instruments, expert surgeons are significantly more accurate than trainee surgeons at performing the saw cuts necessary to position a medial UKA tibial component according to a pre-operative plan. However, PSI immediately allowed the same trainee surgeons, who had not previously performed a UKA, to achieve the same level of overall accuracy as the expert surgeons. Furthermore, for coronal alignment PSI actually made the trainees, and experts, significantly more accurate than the experts using conventional instruments. Despite this, the PSI cutting guide had no impact on the overall accuracy of the expert surgeons.

The largest error for the expert group using conventional instruments was in the coronal plane, with no statistical difference between the experts and trainees, and significantly lower errors for both the trainees and experts using PSI. Indeed, all four conventional expert saw cuts resulted in more varus angulation than planned (2°–5°). Although this represents a failure to reproduce the pre-operative plan of a tibial component orthogonal to the tibial mechanical axis, it might reflect a subconscious desire to recreate the natural joint line obliquity, which is associated with a lower risk of UKA revision [19, 20]. This might have been exacerbated because the sawbone had a medial proximal tibial angle (MPTA) of 83°, which is outside the normal range [21].

Also interesting was the larger than expected, although not statistically significant, sagittal plane error for the expert group using PSI. This was due to a single large error of 6° by a surgeon unfamiliar with PSI, whose focus on fitting the guide to the bone meant that their normal routine of confirming extra-medullary alignment guide parallelity with the tibial shaft was overlooked. The same error befell the two outliers in the trainee PSI group, and is probably an example of inattentional blindness due to a focus on the new technology. This underlines the importance of simulation training before any technology is used in a clinical setting [22]. The latest Embody PSI design (Embody, London, UK) addresses the risk of sagittal plane error by incorporating a novel patient-specific ankle guide which fixes the posterior slope as per the pre-operative plan.

According to the manufacturer’s guidelines on acceptable implant position in the sagittal (± 5°) and coronal planes (± 5°), for the trainees PSI reduced the number of outliers from 16 to 1 [17]. For the experts, the single large error in posterior slope with PSI meant that the number of outliers increased from zero to one with PSI. These results are comparable to the three outliers reported by Kerens et al. [23] in their first 30 cases using Zimmer Biomet’s commercially available MRI-based Signature® PSI (Warsaw, Indiana).

Two randomised controlled trials (RCTs) concluded that, using 2D radiographs, that MRI-based PSI for UKA does not improve implant positioning compared to conventional instrumentation [14, 24]. However, these two RCTs were conducted by expert UKA surgeons in high-volume centres, so an alternative interpretation is that PSI allows surgeons to replicate expert results. Two previous studies have examined the role of PSI for inexperienced surgeons [25, 26]. A small sawbone study of 16 trainee surgeons, who performed lateral UKA using CT-based PSI and conventional instruments, found no difference in accuracy of implant alignment in the coronal, sagittal, or axial planes between the techniques [25]. However, a recently published clinical trial comparing 25 medial UKA performed using MRI-based PSI by a surgeon with no prior UKA experience, and 25 performed using conventional instrumentation by a surgeon ‘with wide experience’ of UKA, found no difference in tibial component alignment, patient reported outcome scores, or 2-year survival rates [26]. It should be noted that only coronal plane positioning was specified pre-operatively and unfortunately no detail was given regarding the training received by the one inexperienced UKA surgeon. Nonetheless, the results are encouraging and consistent with the findings in our study.

Other factors, such as patient selection, might contribute to the caseload effect on UKA revision rates. However, it is known that UKAs performed by low-volume surgeons are more likely to be revised for aseptic loosening and unexplained pain [9]. Evidence from previous studies suggest that tibial component positioning is an important factor in both these factors. In a retrospective review of 559 medial UKAs by Chatellard et al. [13], tibial components orientated more than 3° from the native joint line in the coronal plane were associated with decreased prosthesis survival. However, a finite element (FE) model analysis by Innocenti et al. predicted higher stresses in the underlying cancellous bone when the tibial implant was positioned outside of 0°–3° varus in the coronal plane [27]. As well as increasing the risk of aseptic loosening, higher bone stresses increase the risk of revision surgery due to pain [28]. In the sagittal plane, Chatellard et al.’s study also identified that a posterior slope greater than 5°, or a change in the native tibial slope of more than 2°, increased the risk of implant failure [13]. This is supported by biomechanical studies, with a significant increase in underlying bone strain with posterior slopes greater than 5° [29, 30]. In our study, this level of accuracy was delivered using PSI, with mean absolute error in tibial component positioning for the trainees being significantly less than 3° in the coronal and sagittal planes (p < 0.0001 for both). Yet, with conventional instrumentation, mean trainee error was not less than 3° in the coronal plane (p = 0.3382) and significantly more than 3° in the sagittal plane (p = 0.0259).

The cost-effectiveness of assistive technology is relevant to this study. A Markov model analysis of robotic-assisted UKA calculated an incremental cost of $150,000 per quality-adjusted life-year (QUALY) with a case volume of 32 per annum [31]. For lower-volume surgeons, who arguably have the most to gain from assistive technology, the price per QUALY would be even higher. Although PSI is undoubtedly cheaper than robotic technology, there are no published cost-effectiveness studies of PSI for UKA. In TKA, the value of PSI remains unclear; two studies have concluded that associated improvements in operating room efficiency offset any additional costs [32, 33], whilst a study by Barrack et al. [34] reached a different conclusion. However, these studies are based on the assumption that PSI does not improve component alignment in TKA, which our sawbone study suggests might not be the case for low-volume UKA surgeons.

Our study has some limitations. The results only apply to the two designs of guide tested, and therefore cannot be generalised. Oxford Phase III instruments (Zimmer Biomet, Bridgend, UK) instruments were used in this study. A newer instrumentation set (Oxford Microplasty) has been developed by the same manufacturer, but uses a similar instrument to guide tibial resection in the coronal, sagittal, and axial planes. Indeed, a recent study by Walker et al. [35] comparing their first 100 cases using the Phase III instruments, with their first 100 cases using the Microplasty instruments, found no difference in the accuracy of tibial component positioning. Trainees without prior experience of UKA were tested, and it is unknown whether their results are representative of low-volume UKA surgeons. Albeit, the most common mean UKA caseload in the UK is one per year, and so arguably these surgeons are not much more familiar with the procedure than a trainee. It is also important to recognise that the results probably represent a best case scenario for both instruments, because, in vivo, the visualisation of key landmarks through a mini-arthrotomy is more challenging, and soft tissue makes PSI positioning more difficult. It was assumed that the tibial implant sits perfectly on the cut bone surface, and so any potential variability between expert and trainee cementation technique was not considered. However, this would not be a factor when using the newer cementless Oxford implants (Zimmer Biomet, Bridgend, UK), which have been shown in an independent series to be a safe alternative to the cemented version [36]. The decision to examine tibial component alignment, but not resection depth, was a conscious one given that resection depth is an intra-operative decision based on soft tissue tension.


Higher UKA revision rates in inexperienced or low-volume surgeons has led to the suggestion that the procedure should only be carried out in expert centres [9,10,11]. However, with almost 50% of patients suitable for UKA, this may not be practical [37]. Assistive technology to improve component positioning is one solution and, whilst robotics are unlikely to be economically viable in a low-volume practice, PSI appears ideally placed to help [31, 32].

This study examined the difference in UKA tibial saw cuts between expert and non-expert surgeons. It demonstrates that in a sawbone model, the novel PSI tested allows inexperienced surgeons to achieve the same level of accuracy as expert surgeons. The next step is to ascertain if these results can be replicated in a clinical trial. Whether these improvements translate to improved patient outcomes and lower revision rates is, in part, likely to depend on the quality of the pre-operative plan, and the use of expert trained planning algorithms might be necessary.


  1. 1.

    Jones GG, Kotti M, Wiik AV et al (2016) Gait comparison of unicompartmental and total knee arthroplasties with healthy controls. Bone Joint J 98-B:16–21.

    CAS  Article  PubMed  PubMed Central  Google Scholar 

  2. 2.

    Liddle AD, Pandit H, Judge A, Murray DW (2015) Patient-reported outcomes after total and unicompartmental knee arthroplasty: a study of 14 076 matched patients from the national joint registry for England and Wales. Bone Jt J 97-B(6):793–801.

    CAS  Article  Google Scholar 

  3. 3.

    Liddle AD, Judge A, Pandit H, Murray DW (2014) Adverse outcomes after total and unicompartmental knee replacement in 101330 matched patients: a study of data from the National Joint Registry for England and Wales. Lancet 384(9952):1437–1445.

    Article  PubMed  Google Scholar 

  4. 4.

    Hunt LP, Ben-Shlomo Y, Clark EM et al (2014) 45-day mortality after 467779 knee replacements for osteoarthritis from the National Joint Registry for England and Wales: An observational study. Lancet 384(9952):1429–1436.

    Article  PubMed  Google Scholar 

  5. 5.

    Green M, Wishart N, Young E, Mccormack V, Swanson M (2016) National Joint Registry for England, Wales, Northern Ireland and the Isle of Man 14th Annual Report 2017

  6. 6.

    Hip and Knee Arthroplasty Annual Report (2015) Aust Orthop Assoc Natl Jt Replace Regist. 2015

  7. 7.

    Annual Report (2015)—Swedish Knee Arthroplasty Register.

  8. 8.

    Robertsson O, Surgeon Knutson OK, Professor Lewold AS et al (2001) The routine of surgical management reduces failure after unicompartmental knee arthroplasty. J Bone Jt Surg [Br] 8383(1):45–49

    Article  Google Scholar 

  9. 9.

    Liddle AD, Pandit H, Orth F, Judge A, Murray DW. Effect of surgical caseload on revision rate following total and unicompartmental knee replacement. 2016;98:1–8.

    Article  Google Scholar 

  10. 10.

    Badawy M, Espehaug B, Indrekvam K, Havelin LI, Furnes O (2014) Higher revision risk for unicompartmental knee arthroplasty in low-volume hospitals. Acta Orthop 85(4):342–347.

    Article  PubMed  PubMed Central  Google Scholar 

  11. 11.

    Baker P, Jameson S, Critchley R, Reed M, Gregg P, Deehan D (2013) Center and surgeon volume influence the revision rate following unicondylar knee replacement: an analysis of 23,400 medial cemented unicondylar knee replacements. J Bone Joint Surg Am 95(8):702–709.

    Article  PubMed  Google Scholar 

  12. 12.

    Zhang Q, Zhang Q, Guo W et al (2014) The learning curve for minimally invasive Oxford phase 3 unicompartmental knee arthroplasty: cumulative summation test for learning curve (LC-CUSUM). J Orthop Surg Res 9:81.

    Article  PubMed  PubMed Central  Google Scholar 

  13. 13.

    Chatellard R, Sauleau V, Colmar M, Robert H, Raynaud G, Brilhault J (2013) Medial unicompartmental knee arthroplasty: does tibial component position influence clinical outcomes and arthroplasty survival? Orthop Traumatol Surg Res 99(4 SUPPL):S219–S225.

    CAS  Article  PubMed  Google Scholar 

  14. 14.

    Ollivier M, Parratte S, Lunebourg A, Viehweger E, Argenson JN (2016) The john insall award: no functional benefit after unicompartmental knee arthroplasty performed with patient-specific instrumentation: a randomized trial. Clin Orthop Relat Res 474(1):60–68.

    Article  PubMed  Google Scholar 

  15. 15.

    Logishetty K, Jones GG, Cobb JP (2015) Letter to the editor: the John Insall award: no functional benefit after unicompartmental knee arthroplasty performed with patient-specific instrumentation: a randomized trial. Clin Orthop Relat Res.

    Article  PubMed Central  Google Scholar 

  16. 16.

    Cobb JP, Dixon H, Dandachli W, Iranpour F (2008) The anatomical tibial axis: reliable rotational orientation in knee replacement. J Bone Jt Surg Br 90-B(8):1032–1038.

    Article  Google Scholar 

  17. 17.

    Murray BD, Goodfellow J, Dodd C (1998) Oxford TM partial knee manual of the surgical technique. Biomet UK Healthcare Ltd, Oxford.

  18. 18.

    Landis JR, Koch GG (1977) The measurement of observer agreement for categorical data. Biometrics 33(1):159–174

    CAS  Article  Google Scholar 

  19. 19.

    Zambianchi F, Digennaro V, Giorgini A et al (2014) Surgeon’s experience influences UKA survivorship: a comparative study between all-poly and metal back designs. Knee Surgery Sport Traumatol Arthrosc 23(7):2074–2080.

    Article  Google Scholar 

  20. 20.

    Cartier P, Sanouiller J-L, Grelsamer RP (1996) Unicompartmental knee arthroplasty surgery: 10-year minimum follow-up period. J Arthroplasty 11(7):782–788.

    CAS  Article  PubMed  Google Scholar 

  21. 21.

    Paley D, Pfeil J (2000) Principles of deformity correction around the knee. Orthopade 29(1):18–38.

    CAS  Article  PubMed  Google Scholar 

  22. 22.

    Most SB, Simons DJ, Scholl BJ, Chabris CF (2000) Gorrilas in our midst: sustained inattentional blindness for dynamic events. Perception 28:1059–1074

    Google Scholar 

  23. 23.

    Kerens B, Schotanus MGM, Boonen B, Kort NP (2015) No radiographic difference between patient-specific guiding and conventional Oxford UKA surgery. Knee Surg Sports Traumatol Arthrosc 23(5):1324–1329.

    Article  PubMed  Google Scholar 

  24. 24.

    Alvand A, Khan T, Jenkins C et al (2017) The impact of patient-specific instrumentation on unicompartmental knee arthroplasty: a prospective randomised controlled study. Knee Surg Sports Traumatol Arthrosc 26(6):1662–1670.

    Article  PubMed  PubMed Central  Google Scholar 

  25. 25.

    Ng CTJ, Newman S, Harris S, Clarke S, Cobb J (2017) Patient-specific instrumentation improves alignment of lateral unicompartmental knee replacements by novice surgeons. Int Orthop 41(7):1379–1385.

    Article  PubMed  Google Scholar 

  26. 26.

    Sanz-Ruiz P, Matas-Diez JA, Carbo-Laso E, Perez-Mañanes R, Vaquero-Martín J (2018) Patient-specific instrument can improve functional and radiographic results during learning curve for Oxford unicompartmental knee arthroplasty. J Knee Surg.

    Article  PubMed  Google Scholar 

  27. 27.

    Innocenti B, Pianigiani S, Ramundo G, Thienpont E (2016) Biomechanical effects of different varus and valgus alignments in medial unicompartmental knee arthroplasty. J Arthroplasty.

    Article  PubMed  Google Scholar 

  28. 28.

    Pegg EC, Walter J, Mellon SJ et al (2013) Evaluation of factors affecting tibial bone strain after unicompartmental knee replacement. J Orthop Res 31(5):821–828.

    Article  PubMed  Google Scholar 

  29. 29.

    Small SR, Berend ME, Rogge RD, Archer DB, Kingman AL, Ritter MA (2013) Tibial loading after UKA: Evaluation of tibial slope, resection depth, medial shift and component rotation. J Arthroplasty 28(9 SUPPL):179–183.

    Article  PubMed  Google Scholar 

  30. 30.

    Sawatari T, Tsumura H, Iesaka K, Furushiro Y, Torisu T (2005) Three-dimensional finite element analysis of unicompartmental knee arthroplasty—the influence of tibial component inclination. J Orthop Res 23(3):549–554.

    CAS  Article  PubMed  Google Scholar 

  31. 31.

    Moschetti WE, Konopka JF, Rubash HE, Genuario JW (2015) Can robot-assisted unicompartmental knee arthroplasty be cost-effective? A markov decision analysis. J Arthroplasty 31(4):759–765.

    Article  PubMed  Google Scholar 

  32. 32.

    DeHaan AM, Adams JR, DeHart ML, Huff TW (2014) Patient-specific versus conventional instrumentation for total knee arthroplasty: Peri-operative and cost differences. J Arthroplasty 29(11):2065–2069.

    Article  PubMed  Google Scholar 

  33. 33.

    Tibesku CO, Hofer P, Portegies W, Ruys CJM, Fennema P (2013) Benefits of using customized instrumentation in total knee arthroplasty: results from an activity-based costing model. Arch Orthop Trauma Surg 133(3):405–411.

    Article  PubMed  Google Scholar 

  34. 34.

    Barrack RL, Ruh EL, Williams BM, Ford AD, Foreman K, Nunley RM (2012) Patient specific cutting blocks are currently of no proven value. J Bone Jt Surg Br 94-B(11_Supple_A):95–99.

    Article  Google Scholar 

  35. 35.

    Walker T, Heinemann P, Bruckner T, Streit MR, Kinkel S, Gotterbarm T (2017) The influence of different sets of surgical instrumentation in Oxford UKA on bearing size and component position. Arch Orthop Trauma Surg 137(7):895–902.

    Article  PubMed  Google Scholar 

  36. 36.

    Panzram B, Bertlich I, Reiner T, Walker T, Hagmann S, Gotterbarm T (2017) Cementless Oxford medial unicompartimental knee replacement: an independent series with a 5-year-follow-up. Arch Orthop Trauma Surg 137(7):1011–1017.

    Article  PubMed  Google Scholar 

  37. 37.

    Willis-Owen CA, Brust K, Alsop H, Miraldo M, Cobb JP (2009) Unicondylar knee arthroplasty in the UK National Health Service: an analysis of candidacy, outcome and cost efficacy. Knee 16(6):473–478.

    Article  PubMed  Google Scholar 

Download references


Grant funding was from The Frances and Augustus Newman Foundation and from The Michael Uren Foundation

Author information



Corresponding author

Correspondence to Gareth G. Jones.

Ethics declarations

Conflict of interest

G. Jones declares grants from The Frances and Augustus Newman Foundation and from The Michael Uren Foundation, activity relating to the submitted work. S. Clarke declares provision of equipment from Embody Orthopaedic, activity relating to the submitted work; board membership, royalties and stocks/stock options from Embody Orthopaedic, activity outside the submitted work. M. Jaere declares consultancy for Embody Orthopaedic, activity outside the submitted work. S. Harris declares consultancy for Embody Orthopaedic, activity outside the submitted work. J. Cobb declares grant funding from the Michael Uren Foundation, activity relating to the submitted work; patents and stocks/stock options for Embody Orthopaedic, activity outside the submitted work.

Ethical approval

All procedures performed in studies involving human participants were in accordance with the ethical standards of the institutional and/or national research committee and with the 1964 Helsinki Declaration and its later amendments or comparable ethical standards.

Informed consent

Informed consent was obtained from all individual participants included in the study.

Rights and permissions

Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (, which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Jones, G.G., Logishetty, K., Clarke, S. et al. Do patient-specific instruments (PSI) for UKA allow non-expert surgeons to achieve the same saw cut accuracy as expert surgeons?. Arch Orthop Trauma Surg 138, 1601–1608 (2018).

Download citation


  • Unicompartmental knee arthroplasty
  • Partial knee replacement
  • Patient-specific instrumentation
  • PSI
  • Patient-specific guides
  • 3D printing