Abstract
Shale gas is currently being explored in Europe as an alternative energy source to conventional oil and gas. There is, however, increasing concern about the potential environmental impacts of shale gas extraction by hydraulic fracturing (fracking). In this study, we focussed on the potential impacts on regional water resources within the Baltic Basin in Poland, both in terms of quantity and quality. The future development of the shale play was modeled for the time period 2015–2030 using the LUISA modeling framework. We formulated two scenarios which took into account the large range in technology and resource requirements, as well as two additional scenarios based on the current legislation and the potential restrictions which could be put in place. According to these scenarios, between 0.03 and 0.86 % of the total water withdrawals for all sectors could be attributed to shale gas exploitation within the study area. A screening-level assessment of the potential impact of the chemicals commonly used in fracking was carried out and showed that due to their wide range of physicochemical properties, these chemicals may pose additional pressure on freshwater ecosystems. The legislation put in place also influenced the resulting environmental impacts of shale gas extraction. Especially important are the protection of vulnerable ground and surface water resources and the promotion of more water-efficient technologies.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
There is increasing interest in the development of shale gas as a potential energy source in Europe. Resource estimates have been made for several member states (USDE 2011; Pearson et al. 2012), and exploration is on-going. Due to the low permeability of shale, alternative technologies are applied to increase the recovery rate of the gas. The resource is currently exploited by horizontal drilling of the shale formations to increase borehole contact and high-volume hydraulic fracturing (fracking) to stimulate migration of the gas through the shale. Fracking involves high pressure pumping of fluid through perforations in the well casing in order to produce hydrofractures which propagate through the surrounding shale (King 2012). There are several aspects related to the exploitation of shale gas which may be of concern. These include the occupation of large areas of land (Slonecker et al. 2012; Drohan et al. 2012a; Baranzelli et al. 2014), pollution (Bunch et al. 2014; Moore et al. 2014), impacts on biodiversity (Souther et al. 2014; Brittingham et al. 2014; Northrup and Wittemyer 2013; Kiviat 2013), and possibly seismic triggering (Rutqvist et al. 2013; Geny 2010). For a more detailed review of the available literature, see Kavalov and Pelletier (2012).
In this article, we focus on the possible impact of shale gas extraction by hydraulic fracturing on water resources (Vengosh et al. 2014; Mauter et al. 2014). The consumption of water involved in hydraulic fracturing may place additional pressure on freshwater resources (Arthur et al. 2010), as well as causing potential contamination thereof (Rahm and Riha 2012; Rahm et al. 2013). The competition for freshwater resources in densely populated areas remains an issue, even though some studies claim that energy production using shale gas can actually be more efficient in terms of water use than conventional natural gas (Scott et al. 2011; Mantell 2009). Besides the environmental concerns, the availability of freshwater resources may be a major restriction to companies wanting to extract shale gas commercially, especially where resources are already limited (Mangmeechai et al. 2013).
Four scenarios of shale gas extraction were modeled for our study site using the LUISA modeling platform. The main variables taken into account in the scenario definitions were the technology used, land and water requirements, and the legislation which may be put in place. Several scenarios were used to allow assessment of the range of possible impacts on the freshwater resources available.
Fracking fluid predominately consists of fresh water combined with sand and a variety of chemical additives including corrosion inhibitors, biocides, thickeners, and friction reducers (Arthur et al. 2009; Centner 2013). The impact on water quality will depend on various factors, including the chemical composition of the fracking water, the geology, and the technology used (Abbasi et al. 2014). To date, most studies of the potential environmental impacts of shale gas development have focused on assessing greenhouse gas emissions associated with shale gas production activities (Jiang et al. 2011, Howarth et al. 2011, Weber and Clavin 2012), drinking water quality effects (Osborn et al. 2011; Gross et al. 2013; USEPA 2012a), or regional air quality (McKenzie et al. 2012, Bunch et al. 2014). Entrekin et al. (2011) highlight that the data required to fully understand potential threats to surface water are currently lacking. Rozell and Reaven (2012) studied five pathways of water contamination, assessing the probability of occurrence of water pollution and also advocating the need for further detailed studies. Although there are several studies investigating the nature and magnitude of environmental and human health effects due to chemicals released as a result of shale gas development (Adams 2011; Adgate et al. 2014; Bamberger and Oswald 2012; Hill 2012; Wang et al. 2013; Drohan et al. 2012b), there is still no consensus on the subject. We therefore conducted a screening-level risk assessment of a wide variety of chemicals potentially used in fracking in order to better understand their physicochemical properties, potential fate in the environment, and the associated risk for freshwater.
In the following sections, we introduce the study area and explain the methodology used, including the scenarios adopted for the analysis, the indicators used to assess water demands, and the screening-level risk assessment. The results are then presented and discussed in light of management implications.
Study Area
We looked at a specific case study in Northern Poland where the presence of notable shale gas resources has been confirmed (PGI 2012), and which was deemed the most suitable site for shale gas extraction in Poland in a previous study (Lavalle et al. 2013). The estimated total available shale gas resources within our study area are 386 Bcm (Baranzelli et al. 2014). At the time of writing, exploration drilling is permitted in Poland, but as yet no large-scale exploitation of the resource is being carried out. Figure 1 shows the land use, major cities, and location of several known shale gas exploration wells within and around the study site. The cities of Gdynia, Gdansk, and part of Elblag fall within the study area, as well as several important water bodies along the northern coast, and the Wisla River in the east. The main land uses are agriculture and forest, and there are several national parks situated within the study area.
The Polish Hydrogeological Survey provides detailed information on ground and surface water resources (PHS 2012). The groundwater resources available for development are given in thousands of m3 per day per hydrogeographical region. The average available surface water per sub-catchment was estimated based on the total flow within a catchment over a year. These data were used to represent the available water resources in our study area, as shown in Fig. 2.
According to these estimates, there is substantially more surface water available than groundwater. Groundwater availability is greatest in the northwest and in the regions surrounding the Wisla estuary. Surface resources are also greatest around the Wisla estuary, with much lower flows toward the centre and south of our study area.
Methodology
Shale Gas Extraction Scenarios
We assessed several scenarios of possible future shale gas development in the region for the period 2015–2030. These scenarios are defined in detail in Baranzelli et al. (2014), and include two technological scenarios (relatively higher and lower expected environmental impact) and two legislative scenarios (representing the current legislation in place, and a more restrictive framework). The scenarios were used firstly to determine the most suitable locations for shale gas exploration, and then to allocate the well pads in 5-year time steps using a land use model (EUCS100, Lavalle et al. 2011).
Technological and Water Use Scenarios
In order to assess the influence of the technology used and the rate of development adopted, we defined two scenarios which are representative for the highest and lowest values (in terms of potential environmental impact) of a range of variables characterizing the development of a shale play. These ‘high’ and ‘low’ scenarios also include several parameters which affect the efficiency and total amount of water used. All variables used are summarized in Table 1. The assumed lifespan of the well pads is 10 years in both cases.
We consider both the total amount of freshwater withdrawn for use in the shale gas extraction process (the majority of which is used for fracking), and the share thereof which is ‘consumed,’ i.e., either evaporated, infiltrated into the ground or polluted to an extent that it cannot be directly re-used during the fracking process. The actual amount of water used for shale gas extraction by hydraulic fracturing varies greatly (Sumi 2008; DGIP 2011; Clark et al. 2013), depending on several factors:
-
Local geology (depth, dimensions of shale play, permeability, and type of shale)
-
Technology used (can allow more efficient use of water and reduce leakages)
-
Flowback (amount of water recovered after fracking)
-
Recycling ratio (how much of the water used in fracking is directly re-used on-site)
-
Number of fracks carried out per well
-
Duration of drilling
We reviewed the available literature from 2011 onwards to assess the range of estimated volumes of water required for a single well. Only the most recent estimates were taken into account to reflect the current technology and water use efficiency. The values used to estimate the average water requirements are shown in Fig. 3 (based on Cooley and Donnelly 2012; Grant and Chisholm 2014; USEPA 2011a, b; Hansen et al. 2013; Smith 2010; Sutherland et al. 2011). Estimated water demand ranges from as low as 3500 m3 to almost 50,000 m3 per well (over the whole lifespan), with an average range in water requirements between 8000 and 19,000 m3. We use these values to represent the required volumes for our low and high impact scenarios, respectively.
Upon completion of the fracking process, the direction of fluid flow reverses, with a proportion of the injected fluid returning to the surface. This “flowback” usually ranges from 5 to 50 % of injected freshwater (Sumi 2008; NYSDEC 2011; DGIP 2011), and in some cases may even reach up to 70 % (King 2012). Flowback water may also potentially be recycled, hence reducing cumulative freshwater demands. Gaudlip and Paugh (2008) suggest a recycling rate for flowback water of 70 % in Pennsylvania for best-performing companies, and up to 71.5 % was measured for the Marcellus shale in 2011 (Maloney and Yoxtheimer 2012). This said, on average in the US only some 6–10 % of total water used in fracking is recovered and re-used on-site (Mantell 2011). For the high impact scenario, we therefore assume there to be no recovered or recycled flowback water. In the low impact scenario, we assume a maximum flowback of 70 %, of which 70 % is recycled on-site, so reducing the total amount of water consumed by 49 %.
In the case of Poland, the use of groundwater resources up to 1–2 km deep is permitted (Uliasz-Misiak et al. 2014). Since we lack data on the potential source of water for use in fracking, we assume the same shares as for industrial purposes per catchment. This means that on average for our study area we assume 28 % of the water for fracking to be withdrawn from groundwater resources, and the remaining 72 % from surface water bodies. Since the assumed lifespan of the well pads is 10 years, we divide their water use over two of the 5-year time steps. We assume the water use to be proportional to the gas production, so divide the share of water use according to the production curve presented in Broderick et al. (2011). Seventy percent of the total water use per well pad is therefore allocated in the first time step, and thirty percent in the following time step. This amount was then divided by 5 to estimate the actual amount of water required for 1 year to ensure comparability with the competing water uses (which are calculated annually).
Legislative Scenarios
In addition, a further two scenarios were developed, one based on the current legislation in place and the other representing a potential future legislation which is much more restrictive. The purpose of using these two scenarios in addition was to assess the possible influence that adopting different legislative frameworks may have. In the case of the Marcellus and Utica shales in the US, the amount of water withdrawn for shale gas extraction is regulated. Any surface or groundwater withdrawals exceeding 1,00,000 gallons (378.5 m3) per day require approval from the specific river basin commission (Arthur et al. 2009). Freshwater resources are protected in Poland, although the extent to which varies on a case-by-case basis. There may, for example, be restrictions on the amount of water which can be extracted from a source. Our current legislative scenario excludes shale gas exploitation directly adjacent to water bodies, and in areas potentially at risk of a 100-year return period flood. In addition to this, the restrictive scenario excludes a buffer area of 200 m around all water bodies and waterways. An overview of the assumptions made for the scenarios is given in Table 2. These restrictions are applied at each modeling time step to exclude areas where no well pads can be placed.
Water Quantity Assessment
The water use modeled for each shale gas development scenario was compared to a baseline scenario which excluded any potential shale gas extraction activities. The water use model used (Vandecasteele et al. 2013, 2014) estimates water withdrawals and consumption for the public, industrial, and agricultural sectors. It computes water withdrawals using the reference year 2006, and can forecast to 2030 using various data projections. The methodology is based on the disaggregation of water use statistics to the appropriate land use classes using proxy data. The main statistical data source for Poland was the “Environment 2011” report from the Central Statistical Office of Poland (CSO 2011), which gives water withdrawals for the public, industrial, and agricultural sectors at river basin level. For all sectors, water consumption maps were calculated as a fraction of the withdrawal maps (Vandecasteele et al. 2013). We assumed 20 % of water used for the public supply to be consumed; 15 % of industrial water, and 75 % of agricultural water (mostly used for irrigation). The source of freshwater was also indicated per catchment. On average for our study area, 91 % of public supply is withdrawn from groundwater resources, whereas 72 % of industrial water is withdrawn from surface waterbodies. Due to a lack of data, we assumed agricultural water to be withdrawn from surface resources.
We assume the water used for fracking to be extracted within the same river catchment where the drilling takes place, taking into account that natural gas companies will try to minimize transport costs, which in some cases may exceed the actual cost of the water itself (Arthur et al. 2009). The impact of additional water use for shale gas extraction for the different scenarios is therefore assessed at the river catchment scale, using the water exploitation index (WEI). The index is the ratio of total water withdrawals to the total amount of water available, and can be calculated for both the total amount of water abstracted (WEIabs), and the total amount consumed (WEIcns). We used our water withdrawal and consumption maps in conjunction with the average annual surface and ground freshwater availability to compute both indicators. The WEIcns was also used as a suitability factor to determine where shale gas extraction should be situated in the modeling process (Baranzelli et al. 2014). Where the water exploitation was already high, suitability was decreased, hence discouraging shale gas extraction in that river basin. We compute all water withdrawal and consumption maps and the WEIabs and WEIcns every 5 years, starting from the initial year of possible extraction—2015. The initial baseline indicators for 2015 serve to help define the optimal location for the first well pads. In the subsequent time steps, the indicators are re-calculated for each scenario, allowing us to analyze the spatial and temporal effect of the additional water abstractions required for the shale gas extraction on the state of the available water resources.
Water Quality Assessment
Several issues need to be addressed to ensure that shale gas can be produced in a manner that meets environmental and public health protection goals (Howarth and Ingraffea 2011). Since hydraulic fracturing typically involves the use of large quantities of water and chemicals, associated risks for contamination of ground and surface waters, along with environmental and human health impacts, require careful consideration. In the present paper, we focus on water-related impact. Nevertheless, concern for both ecosystems and human health (both occupational and for the general population) due to chemicals used in shale gas development should be evaluated. Ideally, the assessment should entail the evaluation of:
-
Emissions (quantities and ratios of water, proppants, and chemicals; operational/accidental releases; injected chemicals/formation chemicals)
-
Exposure (fate of the chemicals when emitted into air, water, and soil; exposure pathways for ecosystems and humans)
-
Effects (toxicological endpoint of both the injected and the formation chemicals)
The release of fracking chemicals into the environment may occur under two circumstances: as operational releases (due to the specific processes associated with shale gas development) or as accidental releases. Moreover, two typologies of chemicals should be considered: the chemicals that are injected into the well (injected chemicals) and formation chemicals that are mobilized from the fractured formation and brought to the surface in flowback water. The latter may include heavy metals (some of them particularly toxic (e.g., Hg or Cr)), salts, and radionuclides (Kargbo et al. 2010). The key steps in hydraulic fracturing where operational and/or accidental release of chemicals may occur are indicated in Fig. 4.
Both operational and accidental emissions to air, soil, and both surface and groundwater may occur at several stages in the extraction process, including during storage and transport of chemicals and fracking fluid. This is due to the volatilization of specific chemicals, spillages, and infiltration from surface ponds to soil and groundwater stores. Waste water is either treated on-site, re-injected into the rock mass (Rahm 2011), or transported to (usually industrial) treatment plants. In Poland, discharge to sewage requires a permit, but discharge to industrial waste treatment plants is allowed to some extent (Uliasz-Misiak et al. 2014).
We undertook a screening-level assessment of the potential impacts on water associated with a subset of chemicals recorded in the literature as being currently used in the hydraulic fracturing of shale gas wells. Even though the Polish Environmental Protection Law states that the composition of fracking fluid is not confidential (Uliasz-Misiak et al. 2014), detailed reports of specific chemicals used in Poland are scarce. We therefore based our analysis on a list of over 1000 chemicals used in fracking, as reported by USEPA (2012a) (this list is given in the supplementary information). In order to assess the potential fate of these chemicals in the environment, we needed to (i) identify the processes involved which may incur emissions; (ii) gather data on the physicochemical properties of the chemicals; and (iii) run multimedia fate model. The physicochemical properties were calculated using the EPIsuiteTM (Estimation Programs Interface) model version 4.11Footnote 1 (USEPA 2012b). This is a Windows®-based suite of physicochemical property and environmental fate estimation programs, developed as a screening-level tool, from which we took the physicochemical properties only. Among other results, the model provides two partition coefficients (Kow—partition octanol–water and Kaw—partition water–air), which were used to define the chemical space of the chemicals potentially involved in fracking.
Additionally, the environmental fate and potential harm to freshwater ecosystems and human health were assessed using the multimedia model USEtox (Rosenbaum et al. 2008). USEtox was used to conduct a screening-level assessment of the potential impact of the substances based on different routes and pathways of release. USEtox incorporates a matrix framework for multimedia modeling, allowing the separation of fate, exposure, and ecotoxicity effects in the determination of an overall Characterization Factor (CF). In fact, Usetox includes three basic components: fate factors (FF); exposure factors (XF); and effect factors (EF), which are combined (multiplied) to give a result in comparative toxic units (CTUs). The resulting CTU will therefore be higher with any increase in residence time, higher exposure factor or higher effect factor. An overview of the different components of the USEtox model is given in Table 3.
The resulting CFs (expressed as CTUs) were calculated accounting for potential emissions into water, soil and/or air of a unit of chemical (e.g., 1 kg). As we miss specific information of quantities emitted, our calculation leads to a prioritization of chemicals assuming an equal unit of emission for all of them. Assuming a linear dose–response function for each disease endpoint and intake route, the ecotoxicity effect factor was calculated as 0.5/ED50, where ED50 is the lifetime daily dose resulting in a probability of effect of 0.5.
Results
Competing Water Uses and Exploitation of Freshwater Resources
The water withdrawn for sectoral use is given per catchment and per sector (Fig. 5a, based on statistics obtained from CSO 2011). The industrial sector accounts for the greatest share of water withdrawn in the Wisla Bay and Wisla Basin (up to the Brda catchment). In the remaining catchments, the greatest share is withdrawn for use in the public water supply. The total amount of water withdrawn per km2 remains relatively constant, with the largest amounts being withdrawn in the Brda and Wisla basins. Figure 5b shows the total water withdrawals for 2012, calculated using the same statistics and applying our water use model at 1 km resolution.
According to the simulations carried out with the water use model, there is a steady increase in total water withdrawals from 2015 (119.8 hm3) to 2030 (148.5 hm3) due to a growing population and increasing industrial production. Table 4 gives the total amount of water used in shale gas extraction as a share of the total water withdrawals for each step of the high and low impact technological scenarios. The total water use in the study area is not directly influenced by the type of legislation put in place, so only the differences between the technology scenarios are shown.
If we consider only the water withdrawn within the shale play area, the share of water use for shale gas extraction accounts for up to 0.05 and 0.86 % of the total water withdrawals for all sectors for the low and high impact scenarios, respectively. This is consistent with values found in the US (Table 5, (MIT 2011)).
The WEIcns for surface and groundwater resources was calculated for each scenario. Figure 6 shows the WEIcns for the lowest and highest combined impact scenarios, respectively (LOW = lowest impact technological scenario with restrictive legislative framework; HIGH = highest impact technological scenario with current legislative framework). The figure is overlain with the well pads allocated in 2025 for each scenario combination for comparison.
The increase in impact seen within the shale play corresponds directly to the placement of the well pads. There is also a greater impact on the overall WEIcns calculated for the high combined scenario. Although this difference accounts for only up to a 0.3 % higher WEIcns at the catchment scale, due to the much higher density of well pad placement in the high scenario (shown in the bottom panels for comparison), there will be a much higher impact locally. Changes seen outside the shale play area between scenarios can be attributed to the differing land use maps simulated per shale gas extraction scenario. Depending on where well pads are placed, urban and industrial land may be correspondingly increased or decreased in other regions to compensate and meet the demands which are built into the land use model. This differing land use results in altered water use maps, which in turn directly impact the calculation of the WEI. In the high scenario, the WEIcns for surface water reaches a maximum of 0.83 %, and the WEIcns for groundwater 22.42 %. This indicates that due to the higher impact of withdrawals from groundwater on the overall exploitation, water for shale gas extraction should preferentially be withdrawn from surface water bodies.
Screening Assessment of Potential Impact of Chemicals on Freshwater
The EPIsuiteTM model was run to calculate the physicochemical properties of the list of over 1000 chemicals provided by USEPA (2012a). The distribution of these chemicals in the chemical space defined by the partitioning coefficients Kow and Kaw is reported in Fig. 7. The considerable heterogeneity in physicochemical properties shown—ranging from highly volatile to strongly lipophilic and hydrophilic—highlights that they may follow very different pathways in the environmental fate. It should be noted that, beyond a screening assessment, additional information on chemical properties is needed to further assess the potential fate of chemicals. Log Kow may have limited value for the estimation of environmental fate of chemicals ionized across environmentally relevant pH, which influences bioavailability, partitioning to soils, sediments, organisms, and so on. It has been estimated that one-third of the chemicals registered under REACH are ionizable (Franco et al. 2010). This is a problem affecting several multimedia models including those used in the present study (EPISuite and USEtox), which are optimized for neutral hydrophobic substances (Rosenbaum et al. 2008). Efforts to develop models suitable for ionizing substances are on-going (Van Zelm et al. 2013; Franco and Trapp 2010). However, multimedia model adaptations for accounting for ionizable chemicals typically result in higher freshwater fate factors for ionized acids (pKa < 7), while for ionized bases (pKa > 7), larger as well as smaller fate factors are seen. For acids and bases that are less than 50 % ionized in freshwater, the changes in fate factors are relatively small (<10 %) (Van Zelm et al. 2013). Additionally, site-specific aspects may greatly influence the fate in real water bodies (see e.g., Valenti et al. 2011). Nonetheless, accounting for the above-mentioned limitation, the chemical space covered by the substances demonstrates the need for the proper modeling of chemicals which are very diverse in terms of physicochemical properties and potential fate in the environment.
Applying USEtox, the results were expressed in comparative toxic units (CTUe), which provide an estimate of the potentially affected fraction (PAF) of species integrated over time and volume per unit mass of a chemical emitted (PAF m3 day kg−1). The results highlight wide variability in terms of potential impacts for ecosystems and human health. For example, when chemicals are emitted directly to water, there is tremendous variability in potential impacts (over 12 orders of magnitude). This could be due to the fact that the fate, toxicological properties, and potential harmfulness of the substances are very diverse. When emitted in water, the chemicals that tend to remain in water imply higher CTUe, whereas those that volatilize or are adsorbed by the sediments result in lower CTUe values. These results should be taken with caution, as the fate, the exposure and the effect components may be affected by the presence of ionisable compounds (e.g., for emission into freshwater, the ratio between FF accounting for ionization or assuming neutral substance varies from 0.24 to 1.6; for emission into air, from 0.058 to 6000; Van zelm et al. 2013).
Figure 8 reports the comparative toxic unit for ecotoxicity for all the substances reported by USEPA (2012a), highlighting those frequently mentioned in the literature as main emissions coming from shale gas (e.g., benzene, toluene, ethylbenzene, and xylenes (BTEX), for which values are given in Table 6). Notably, irrespective of the route of the emission, the potential ecotoxicological concern for freshwater related to many chemicals is high, even beyond the value reported for substances already known as being of concern for emission to air and water directly. In the case of emission to soil, the chemicals of concern are relatively few (due to high volatilization, the relative contribution to freshwater ecotoxicity through soil emission is low).
Effect factors are calculated using the AMI method (Payet 2005, as explained in Table 3). This method ensures that the final result is less affected by extreme values.
Discussion
It should be noted that both for the quantity and quality assessments, there were several limitations due to data availability and some assumptions had to be made. For example, although this was not taken into account, wells may also be repeatedly fracked to maximize productivity (Berman 2009; NYSDEC 2011; Ineson 2008). Irrigation water is assumed to be withdrawn from surface water, but may actually in part be extracted from groundwater resources in some cases—this would mean that the stress on groundwater resources is underestimated. The actual situation in terms of water use may also be very different in Europe compared to that in the United States. Indeed, the often-repeated assertion that European shale plays tend to be deeper and more complex suggests that water demands may also be different. This study would therefore benefit from additional European data for the definition of the scenarios as it becomes available.
It should also be stressed that the results of the screening chemical assessment are meant as a screening since the exact products and quantities were missing. Impacts may vary greatly according to spatial and temporal aspects and site-specific contexts. Although this was not possible here due to data limitations, the evaluation should therefore ideally be site-specific (e.g., Vidic et al. 2013). Due to the wide variety of chemicals used and the heterogeneity of their physicochemical properties and associated toxicological concerns, a detailed human and ecological risk assessment is recommended, covering different endpoints and possible targets of impact. Additionally, improving knowledge related to the chemicals potentially involved in both operational and accidental releases is essential. It is also important to note that this analysis has focused on injected chemicals only, whereas formation chemicals may also pose environmental and human health concerns.
The screening assessment undertaken here, along with a review of existing studies, supports the following recommendations (complementary to those provided by Colborn et al. (2011)) for an optimal management and prevention of impacts:
-
Reporting (i) each drilling and fracking operation, as well as total fluid injected; (ii) chemicals used and quantities employed over time; (iii) the level of treatment of flowback and produced water; (iv) potential mixtures of chemicals that may occur in the event of operational or accidental releases; (v) local context, including the geology/hydrogeology and climatic aspects (Ciuffo and Sala 2013);
-
Assessing (i) impacts at different scales: local, regional, and global; (ii) the comprehensive life cycle of shale gas exploitation, from shale play preparation to closure and mid-term/long-term impacts in order to avoid burden shifting between operational stages or impact categories;
-
Policy Synergies Elucidation of the role of the REACH Directive implementation (EC 2006) in the systematic accounting of chemicals used in shale gas exploitation and their related physicochemical and toxicological properties, as already started by Gottardo et al. (2013).
Water handling is estimated to account for some 10 % of the operational cost of a well (Gay et al. 2012), making it an important issue to be addressed by operators. This includes not only the need for management of issues related to water availability but also optimization of disposal, treatment, and transport.
The efficiency of water use in fracking has been noted to be increasing over the last 10 years (Nicot et al. 2014). There have also been several initiatives to substitute fresh water with brackish or even saline water. In Texas, for example, increased pressure on water resources and regional droughts have encouraged the use of brackish groundwater (Standen 2012; Ghahremani and Clapp 2014), which now accounts for up to 30 % of the water used for fracking. The pre-treatment and extraction thereof (in the case of groundwater) are, however, still a major expense. The use of alternative substances to water is also being developed (Rogala et al. 2013; Gandossi 2013), for example, a gelled form of liquid petroleum gas (LPG) used which may even have a higher recovery rate of shale gas (Wilson 2013).
Even though new technologies are being developed for on-site treatment and recycling of flowback water (Miller et al. 2013), produced water is still mostly re-injected into the ground via wells (Nicot et al. 2014). Some of this flowback water may potentially be recovered after desalinization for alternative uses (Shaffer et al. 2013). However, the proper disposal of non-recycled produced water remains a concern.
Conclusions
The methodology used aimed at assessing the range of possible impacts of shale gas extraction on water resources within the current data limitations. Therefore, even though some important conclusions can be drawn, care should be taken in the interpretation of the results.
The scenarios modeled vary greatly in terms of projected water withdrawals and consumption. We took an estimated range of water use per well between 8000 and 19,000 m3, and assumed that in the best case scenario, 70 % of flowback water would be recovered, of which up to 70 % could be recycled, meaning an overall re-use of 49 % of water—in the worst case scenario, we assumed all water to be lost directly to the environment. In the best case, water use for shale gas accounted for only 0.03 % of the total water use for all sectors within the shale play. In the worst case scenario, this proportion rose to 0.86 %, at which point there may be impacts seen locally, especially where there are already water shortages or periods of drought. The wide range in estimated absolute water use per scenario stresses the importance of water use efficiency to reduce the overall impact on the direct environment. The share of water use attributed to shale gas extraction locally was comparable to those found in the major shale plays in the USA (Table 5). The WEIcns was also seen to vary considerably according to the scenario and the maximum in the last calculated time step (2028) was 0.83 % for surface water, and 22.4 % for groundwater. This highlights the importance of the source from which water is extracted—for the scenarios run, we assumed on average 28 % of fracking water to originate from groundwater resources, but in fact, this amount should be minimized due to the limited availability of groundwater compared to surface resources.
The study showed that additional pressure would be put on local water resources due to future shale gas extraction. The extent to which the development of this resource will impact on the direct aquatic environment varies greatly with the rate of extraction, the technology used, and especially the efficiency of water use and the recycling thereof. Maximizing the recovery of water as flowback, and increasing the recycling ratio would reduce the absolute water requirements per well, and reduce both the impact on the environment and the cost of transport for the companies involved.
In the screening-level risk assessment carried out, physicochemical properties were estimated with EPISuiteTM (suited for screening analysis only), the fate in the environment was assessed using a box model (USEtox), and the effects were evaluated only for freshwater and adopting EC50 as endpoint. Beyond current limitations, the analysis performed allows the identification of some important elements. The evaluation highlighted that many of the chemicals used may pose ecosystem health risks. Of special concern is the heterogeneity of the chemicals and their physicochemical properties, meaning they may propagate and persist in all mediums (not just water but also air and soil). This in turn leads to a wide range of associated toxicological concerns. Some of the chemicals present in the list of those used in fracking (e.g., BTEX) are of very high concern not only for drinking water (Gross et al. 2013; Swanson and Krause 2011), but also for ecotoxicity-related impacts. This is of particular importance if we consider that some of those chemicals present a potential risk higher than those of the substances usually monitored or reported in the literature for shale gas.
Figure 7 indicates the numerous stages in the shale gas extraction process where there may be accidental or operational release of substances (both wastewater and chemicals directly), and where special attention should be paid to the reduction of accidental losses, and the proper regulation of operational releases. Concerning the possible contamination of water due to shale gas exploitation, the results clearly showed that there is a need to further integrate risk assessment and life cycle assessment methodologies in the analysis of the environmental risk associated to shale gas development, as in Mangmeechai et al. 2013.
The more efficiently water can be used, and the higher the flowback and recycling ratio achieved, the lower will be the overall impact on freshwater resources, also in terms of water quality considerations.
Notes
The EPI (Estimation Programs Interface) Suite™ is a Windows®-based suite of physicochemical property and environmental fate estimation programs. EPI Suite™ is a screening-level tool and should not be used if acceptable measured values are available.
References
Abbasi MA, Ezulike DO, Dehghanpour H, Hawkes RV (2014) A comparative study of flowback rate and pressure transient behavior in multifractured horizontal wells completed in tight gas and oil reservoirs. J Nat Gas Sci Eng 17:82–93. doi:10.1016/j.jngse.2013.12.007
Adams MB (2011) Land application of hydrofracturing fluids damages a deciduous forest stand in West Virginia. J Environ Qual 40:1340–1344
Adgate JL, Goldstein BD, McKenzie LM (2014) Potential public health hazards, exposures and health effects from unconventional natural gas development. Environ Sci Technol 48(15):8307–8320
Arthur DJ, Bohm B, Layne M (2009) Hydraulic fracturing considerations for natural gas wells of the Marcellus Shale. In: Gulf coast association of geological societies transactions, vol 59. pp 49–59
Arthur DJ, Spec PE, Uretsky M, Wilson P (2010) Water resources and use for hydraulic fracturing in the marcellus shale region, ALL Consulting LLC
Bamberger M, Oswald RE (2012) Impacts of gas drilling on human and animal health. New Solut 22:51–77
Baranzelli C, Vandecasteele I, Barranco R, Mari Rivero I, Pelletier N, Lavalle C (2014) Scenarios for shale gas development in the Baltic Basin, Northern Poland, under review for Environmental Science and Policy
Berman A (2009) Lessons from the Barnett Shale suggest caution in other shale plays. Association for the Study of Peak Oil and Gas, USA. http://www.aspousa.org/index.php/2009/08/lessons-from-the-barnett-shale-suggest-caution-in-other-shale-plays/
Brittingham MC, Maloney KO, Farag AM, Harper DD, Bowen ZH (2014) Ecological risks of shale oil and gas development to wildlife, aquatic resources and their habitats. Environ Sci Technol 48(19):11034–11047
Broderick J, Anderson K, Wood R, Gilbert P, Sharmina M, Footitt A, Glynn S, Nicholls F (2011) Shale gas: an updated assessment of environmental and climate change impacts, Tyndall Centre, University of Manchester
Bunch AG, Perry CS, Abraham L, Wikoff DS, Tachovsky JA, Hixon JG, Urban JD, Harris MA, Haws LC (2014) Evaluation of impact of shale gas operations in the Barnett Shale region on volatile organic compounds in air and potential human health risks. Sci Total Environ 468–469:832–842. doi:10.1016/j.scitotenv.2013.08.080
Centner TJ (2013) Oversight of shale gas production in the United States and the disclosure of toxic substances. Resour Policy 38:233–240. doi:10.1016/j.resourpol.2013.03.001
Ciuffo B, Sala S (2013) Climate-based archetypes for the environmental fate assessment of chemicals. J Environ Manag 129:435–443
Clark CE, Horner RM, Harto CB (2013) Life cycle water consumption for shale gas and conventional natural gas. Environ Sci Technol 47:11829–11836
Colborn T, Kwiatkowski C, Schultz K, Bachran M (2011) Natural gas operations from a public health perspective. Human and ecological risk assessment: An International Journal 17(5):1039–1056
Cooley H, Donnelly K (2012) Hydraulic fracturing and water resources: separating the frack from the fiction. Pacific Institute, Oakland
CSO (2011) Environment 2011 Regional and Environmental Surveys Division, Central Statistical Office of Poland (ISSN 0867-3217)
DGIP (2011) Impacts of shale gas and shale oil extraction on the environment and on human health. Directorate General for Internal Policies, European Parliament
Drohan P, Brittingham M, Bishop J, Yoder K (2012a) Early trends in landcover change and forest fragmentation due to shale-gas development in Pennsylvania: a potential outcome for the northcentral Appalachians. Environ Manag 49:1061–1075
Drohan PJ, Finley J, Roth P, Schuler T, Stout S, Brittingham M, Johnson NC (2012b) Oil and gas impacts on forest ecosystems: findings gleaned from the 2012 Goddard Forum at Penn State University. Environ Pract 14(4):394–399
EC (2006). Regulation (EC) No 1907/2006 of the European Parliament and of the Council of 18 December 2006 concerning the Registration, Evaluation, Authorization, and Restriction of Chemicals (REACH), establishing a European Chemicals Agency. Official J Eur Union 30.12.2006. http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=oj:l:2006:396:0001:0849:en:pdf
Entrekin S, Evans-White M, Johnson B, Hagenbuch E (2011) Rapid expansion of natural gas development poses a threat to surface waters. Front Ecol Environ 9(9):503–511
Franco A, Trapp S (2010) A multimedia activity model for ionizable compounds: validation study with 2, 4-dichlorophenoxyacetic acid, aniline, and trimethoprim. Environ Toxicol Chem 29(4):789–799
Franco A, Ferranti A, Davidsen C, Trapp S (2010) An unexpected challenge: ionizable compounds in the REACH chemical space. Int J Life Cycle Assess 15(4):321–325
Gandossi L (2013) An overview of hydraulic fracturing and other formation stimulation technologies for shale gas production, EUR 26347 Joint Research Centre Scientific and Technical Research series, Publications Office of the European Union, Luxembourg. doi:10.2790/99937
Gaudlip A, Paugh L (2008) Marcellus shale water management challenges in Pennsylvania. Society of Petroleum Engineers, Richardson
Gay MO, Fletcher S, Meyer N, Gross S (2012) Water management in shale gas play. HIS water white paper. Available at http://www.ihs.com/info/en/a/shale-gas-water-management.aspx. Accessed July 2014
Geny F (2010) Can unconventional gas be a game changer in European gas markets?, NG46. The Oxford Institute for Energy Studies, Oxford
Ghahremani N, Clapp L (2014) Feasibility of using brackish groundwater desalination concentrate as hydraulic fracturing fluid in the Eagle Ford Shale. In: Shale Energy Engineering 2014@ sTechnical Challenges, Environmental Issues, and Public Policy. ASCE, pp. 23–32
Gottardo S, Amenta V, Mech A, Sokull-Kluettgen B (2013) Assessment of the use of substances in hydraulic fracturing of shale gas reservoirs under REACH. EUR 26069—Joint Research Centre—Institute for Health and Consumer Protection. Publications Office of the European Union, Luxembourg
Grant L, Chisholm A (2014) Shale gas and water: An independent review of shale gas exploration and exploitation in the UK with a particular focus on the implications for the water environment. The Chartered Institution of Water and Environmental Management (CIWEM), London. http://oesg.org.uk/wp-content/uploads/2014/12/CIWEM-shale-gas-report-Shale-Gas-and-Water.pdf
Gross SA, Avens HJ, Banducci AM, Sahmel J, Panko JM, Tvermoes BE (2013) Analysis of BTEX groundwater concentration from surface spills associated with hydraulic fracturing operations. J Air Waste Manag Assoc 63(4):424–432
Hansen E, Mulvaney D, Betcher M (2013) Water resource reporting and water footprint from Marcellus Shale development in West Virginia and Pennsylvania
Hill EL (2012) Unconventional natural gas development and infant health: evidence from Pennsylvania. Charles H. Dyson School of Applied Economics and Management Working Paper 12
Howarth RW, Ingraffea A (2011) Should fracking stop comment. Nature 477:271–274
Howarth RW, Santoro R, Ingraffea A (2011) Methane and the greenhouse-gas footprint of natural gas from shale formations. Clim Change 106:679–690
Huijbregts M, Hauschild M, Jolliet O, Margni M, McKone T, Rosenbaum RK, van de Meent D (2010) USEtox™ user manual. USEtox™ Team. Available at http://www.usetox.org/
Ineson (2008) Changing geography of North American natural gas. INGAA Foundation
Jiang M, Griffin WM, Hendrickson C, Jaramillo P, VanBriesen J, Venkatesh A (2011) Life cycle greenhouse gas emissions of Marcellus Shale gas. Environ Res Lett 6:034014
Kargbo D, Wilhelm R, Campbell D (2010) Natural gas plays in the Marcellus Shale: challenges and potential opportunities. Environ Sci Technol 44:5679–5684
Kavalov B, Pelletier N (2012) Shale gas for Europe: main environmental and social considerations (a literature review). Scientific and Policy Report of the Joint Research Centre, Publications Office of the European Union, Luxembourg (ISBN 978-92-79-26277-7)
King GE (2012) Hydraulic fracturing 101: What Every Representative Environmentalist Regulator Reporter Investor University Researcher Neighbor and Engineer Should Know about Estimating Frac Risk and Improving Frac Performance in Unconventional Gas and Oil Wells, 152596. (SPE)
Kiviat E (2013) Risks to biodiversity from hydraulic fracturing for natural gas in the Marcellus and Utica shales. Ann N Y Acad Sci 1286:1–14
Lavalle C, Baranzelli C, Batista e Silva F, Mubareka S, Rocha Gomes C, Koomen E, Hilferink M (2011) A high resolution land use/cover modelling framework for Europe. ICCSA 2011, Part I, LNCS 6782, pp. 60–75. doi:10.1007/978-3-642-21928-3
Lavalle C, Baranzelli C, Vandecasteele I, Ribeiro Barranco R, Sala S, Pelletier N (2013) Spatially-resolved Assessment of Land and Water Use Scenarios for Shale Gas Development: Poland and Germany. JRC Technical Report
Maloney KO, Yoxtheimer DA (2012) Production and disposal of waste materials from gas and oil extraction from the Marcellus Shale Play in Pennsylvania. Environ Pract 14:278–287
Mangmeechai A, Jaramillo P, Griffin WM, Matthews HS (2013) Life cycle consumptive water use for oil shale development and implications for water supply in the Colorado River Basin. Int J Life Cycle Assess 19(3):677–687
Mantell ME (2009) Deep shale natural gas: abundant, affordable, and surprisingly water efficient. Water/Energy Sustainability Symposium: Groundwater Protection Council Annual Forum, Salt Lake City, UT, 2009
Mantell ME (2011) Produced water reuse and recycling challenges and opportunities across major shale plays. In: Proceedings of the Technical Workshops for the Hydraulic Fracturing Study: Water Resources Management. EPA 600/R-11/048, May 2011, pp. 49–57
Massachusetts Institute of Technology MIT (2011) The future of natural gas—an interdisciplinary MIT Study. Massachusetts Institute of Technology, Cambridge
Mauter MS, Alvarez PJJ, Burton A, Cafaro DC, Chen W, Gregory KB, Jiang G, Li Q, Pittock J, Reible D, Schnoor JL (2014) Regional variation in water-related impacts of shale gas development and implications for emerging international plays. Environ Sci Technol 48(15):8298–8306
McKenzie LM, Witter RZ, Newman LS, Adgate JL (2012) Human health risk assessment of air emissions from development of unconventional natural gas. Sci Total Environ 424:79–87
Miller DJ, Huang X, Li H, Kasemset S, Lee A, Agnihotri D, Hayes T, Paul DR, Freeman BD (2013) Fouling-resistant membranes for the treatment of flowback water from hydraulic shale fracturing: a pilot study. J Membr Sci 437:265–275
Moore CW, Zielinska B, Pétron G, Jackson RB (2014) Air impacts of increased natural gas acquisition, processing, and use: a critical review. Environ Sci Technol 48(15):8349–8359
Nicot J-P, Scanlon BR, Reedy RC, Costley RA (2014) Source and fate of hydraulic fracturing water in the Barnett Shale: a historical perspective. Environ Sci Technol 48(4):2464–2471
Northrup JM, Wittemyer G (2013) Characterising the impacts of emerging energy development on wildlife, with an eye towards mitigation. Ecol Lett 16:112–125
NYSDEC (2011) New York State Department of Environmental Conservation, Revised Draft Supplemental Generic Environmental Impact Statement On The Oil, Gas and Solution Mining Regulatory Program, New York
Osborn SG, Vengosh A, Warner NR, Jackson RB (2011) Methane contamination of drinking water accompanying gas-well drilling and hydraulic fracturing. Proc Natl Acad Sci 108(20):8172–8176
Payet J (2005) Assessing toxic impacts on aquatic ecosystems in LCA. Int J Life Cycle Assess 10(5):373
Pearson I, Zeniewski P, Gracceva F, Zastera P, McGlade C, Sorrell S, Speirs J, Thonhauser G (2012) Unconventional Gas: Potential Energy Market Impacts in the EU. Scientific and Policy Report of the Joint Research Centre, Publications Office of the European Union, Luxembourg (ISBN 978-92-79-19908-0)
PGI Polish Geological Institute—National Research Institute (2012) Assessment of shale gas and shale oil resources of the Lower Paleozoic Baltic-Podlasie-Lublin Basin in Poland
PHS—Polish Hydrogeological Survey (2012) http://epsh.pgi.gov.pl/epsh/
Rahm D (2011) Regulating hydraulic fracturing in shale gas plays: the case of Texas. Energy Policy 39:2974–2981
Rahm BG, Riha SJ (2012) Toward strategic management of shale gas development: regional, collective impacts on water resources. Environ Sci Policy 17:12–23
Rahm BG, Bates JT, Bertoia LR, Galford AE, Yoxtheimer DA, Riha SJ (2013) Wastewater management and Marcellus Shale gas development: trends, drivers, and planning implications. J Environ Manag 120:105–113. doi:10.1016/j.jenvman.2013.02.029
Rogala A, Krzysiek J, Bernaciak M, Hupka J (2013) Non-aqueous fracturing technologies for shale gas recovery. Physicochem Prob Miner Process 49(1):313–322
Rosenbaum RK, Bachmann TM, Gold LS, Huijbregts MAJ, Jolliet O, Juraske R, Köhler A, Larsen HF, MacLeod M, Margni M, McKone TE, Payet J, Schuhmacher M, van de Meent D, Hauschild MZ (2008) USEtox—The UNEP-SETAC toxicity model: recommended characterization factors for human toxicity and freshwater ecotoxicity in Life Cycle Impact Assessment. Int J LCA 13(7):532–546
Rozell DJ, Reaven SJ (2012) Water pollution risk associated with natural gas extraction from the Marcellus shale. Risk Anal 32(8):1382–1393. doi:10.1111/j.1539-6924.2011.01757.x
Rutqvist J, Rinaldi AP, Cappa F, Moridis GJ (2013) Modeling of fault reactivation and induced seismicity during hydraulic fracturing of shale-gas reservoirs. J Petrol Sci Eng 107:31–44. doi:10.1016/j.petrol.2013.04.023
Scott CA, Pierce SA, Pasqualetti MJ, Jones AL, Montz BE, Hoover JH (2011) Policy and institutional dimensions of the water–energy nexus. Energy Policy 39:6622–6630
Shaffer DL, Arias Chavez LH, Ben-Sasson M, Romero-Vargas Castrillon S, Yip NY, Elimelech M (2013) Desalination and reuse of high-salinity shale gas produced water: drivers, technologies, and future directions. Environ Sci Technol 47(17):9569–9583
Slonecker ET, Milheim L, Roig-Silva C, Fisher G (2012) Landscape Consequences of Natural Gas Extraction in Greene and Tioga Counties, Pennsylvania, 2004–2010. U.S. Geological Survey Open-File Report 2012–1220, p. 32
Smith M (2010) Shale gas development in the U.S., IOGCC
Souther S, Tingley MW, Popescu VD, Hayman DTS, Ryan ME, Graves TA, Hartl B, Terrell K (2014) Biotic impacts of energy development from shale: research priorities and knowledge gaps. Front Ecol Environ 12:330–338
Standen AR (2012) Exploration of West Texas brackish groundwater to supply fracking fluids for the Bone Spring play, Gulf Coast Association of Geological Societies Transactions, 2012, pp. 449–459
Sumi L (2008) Shale Gas: Focus on the Marcellus Shale. Oil and Gas Accountability Project/Earthworks
Sutherland WJ, Bardsley S, Bennun L, Clout M, Cote IM, Depledge MH, Dicks LV, Dobson AP, Fellman L, Fleishman E, Gibbons DW, Impey AJ, Lawton JH, Lickorish F, Lindenmayer DB, Lovejoy TE, MacNally R, Madgwick J, Peck LS, Pretty J, Prior SV, Redford KH, Scharlemann JPW, Spalding M, Watkinson AR (2011) Horizon scan of global conservation issues for 2011, CELL PRESS
Swanson L, Krause M (2011) An assessment of some of the environmental and public health issues surrounding hydraulic fractuign in New York State. Report of the New York Marine Science Consortium. Available at http://www.somas.stonybrook.edu/~awp/downloads/NYMSC-FrackingWhitePaper.pdf. Accessed July 2014
Uliasz-Misiak B, Przybycin A, Winid B (2014) Shale and tight gas in Poland—legal and environmental issues. Energy Policy 65:68–77. doi:10.1016/j.enpol.2013.10.026
USDE, US Department of Energy (2011) World shale gas resources: an initial assessment of 14 regions outside the United States. United States Department of Energy, Washington, DC
USEPA (2011a) Plan to study the potential impacts of hydraulic fracturing on drinking water resources—office of research and development. US Environmental Protection Agency, Washington, DC
USEPA (2011b) Supplemental generic environmental impact statement on the oil, gas and solution mining regulatory program well permit issuance for horizontal drilling and high-volume hydraulic fracturing to develop the Marcellus Shale and other low-permeability gas reservoirs
USEPA (2012a) Study of the potential impact of hydraulic fracturing on drinking water resources. Office of Research and Development, United States Environmental Protection Agency, Washington, DC. http://www.epa.gov/hfstudy/
USEPA (2012b) EPI (Estimation Programs Interface) Suite™, version 4.11 Nov 2012. Available at http://www.epa.gov/opptintr/exposure/pubs/episuite.htm. Accessed May 2013
Valenti TW, Taylor JM, Back JA, King RS, Brooks BW (2011) Influence of drought and total phosphorus on diel pH in wadeable streams: implications for ecological risk assessment of ionizable contaminants. Integr Environ Assess Manag 7(4):636–647
Van Zelm R, Stam G, Huijbregts MA, van de Meent D (2013) Making fate and exposure models for freshwater ecotoxicity in life cycle assessment suitable for organic acids and bases. Chemosphere 90(2):312–317
Vandecasteele I, Bianchi A, Mubareka S, De Roo A, Burek P, Bouraoui F, Lavalle C, Batelaan O (2013) Mapping of current and projected Pan-European water withdrawals, UNCCD 2nd Scientific Conference, Proceedings, 9–12 April 2013
Vandecasteele I, Bianchi A, Batista e Silva F, Lavalle C, Batelaan O (2014) Mapping current and future European public water withdrawals and consumption. Hydrol Earth Syst Sci 18:407–416. doi:10.5194/hess-18-407-2014
Vengosh A, Jackson RB, Warner N, Darrah TH, Kondash A (2014) A critical review of the risks to water resources from unconventional shale gas development and hydraulic fracturing in the United States. Environ Sci Technol 48(15):8334–8348
Vidic RD, Brantley SL, Vandenbossche JM, Yoxtheimer D, Abad JD (2013) Impact of shale gas development on regional water quality. Science 340(6134):1235009
Wang N, Ingersoll CG, Kunz JL, Brumbaugh WG, Kane CM, Evans RB, Alexander S, Walker C, Bakaletz S (2013) Toxicity of sediments potentially contaminated by coal mining and natural gas extraction to unionid mussels and commonly tested benthic invertebrates. Environ Toxicol Chem 32:207–221
Weber CL, Clavin C (2012) Life cycle carbon footprint of shale gas: review of evidence and implications. Environ Sci Technol 46:5688–5695
Wilson BT (2013) GasFrac: a cost-benefit analysis of hydraulic fracturing with liquefied petroleum gas gel. J Technol Law Policy 14(1):142–157. doi:10.5195/tlp.2013.137
Author information
Authors and Affiliations
Corresponding author
Electronic supplementary material
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution License which permits any use, distribution, and reproduction in any medium, provided the original author(s) and the source are credited.
About this article
Cite this article
Vandecasteele, I., Marí Rivero, I., Sala, S. et al. Impact of Shale Gas Development on Water Resources: A Case Study in Northern Poland. Environmental Management 55, 1285–1299 (2015). https://doi.org/10.1007/s00267-015-0454-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00267-015-0454-8