Skip to main content
SpringerLink
Log in

Analysis of temperature field in dry sliding wear test on pin-on-disc

  • Technical Note
  • Published:
Heat and Mass Transfer Aims and scope Submit manuscript

Abstract

The heat flux generated due to friction between two metal bodies and the corresponding convective heat transfer coefficient are calculated from the basics of heat transfer. The dry sliding friction in pin-on-disc is considered for analysis and respective model is established using finite element method. Later the temperature distribution in pin and disc material are analyzed. As pin material exposed to surrounding atmosphere, the temperature and coefficient of heat convection is highest at the centre and gradually decreased towards outer surface and away from the friction contact surface of the pin. Due to the dry sliding friction the flow of heat and temperature rose rapidly at the initial stages and later reached the equilibrium stages. It is proved with good agreement in comparison of experimental and simulation results. The present work concentrates on the feasibility in studying pin-on-disc dry sling friction by simulation method.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4

References

  1. Majcherczak D, Dufrenoy P, Berthier Y (2007) Tribological, thermal and mechanical coupling aspects of the dry sliding contact. Tribol Int 40:834–843

    Article  Google Scholar 

  2. Holmberg K, Andersson P, Erdemir A (2012) Global energy consumption due to friction in passenger cars. Tribiology Int 47:221–234

    Article  Google Scholar 

  3. Gui L, Wang X, Fan Z, Zhang F (2016) A simulation method of thermo-mechanical and tribological coupled analysis in dry sliding systems. Tribiology Int 103:121–131

    Article  Google Scholar 

  4. Le NTP, Anh N, Tan L (2016) Effect of the sliding friction on heat transfer in high-speed rare fied gas fl ow simulations in CFD. Int J Therm Sci 109:334–341

    Article  Google Scholar 

  5. Kennedy FE, Lu Y, Baker I (2015) Contact temperatures and their influence on wear during pin-on-disk tribotesting. Tribol Int 82:534–542

    Article  Google Scholar 

  6. Podra P, Andersson S (1999) Simulating sliding wear with finite element method. Tribol Int 32:71–81

    Article  Google Scholar 

  7. Bortoleto EM, Rovani AC, Seriacopi V, Profito FJ, Zachariadis DC, Machado IF (2013) Experimental and numerical analysis of dry contact in the pin on disc test. Wear:1–8

  8. Belyakov N, Nosko O (2016) Analytical solution of non-stationary heat conduction problem for two sliding layers with time-dependent friction conditions. Int J Heat Mass Transf 98:624–630

    Article  Google Scholar 

  9. Kumar V, Gautam RK, Tyagi R (2016) Tribological behavior of Al-based self-lubricating composites. Composite Interfaces 6440

  10. Bahri A, Guermazi N, Elleuch K, Urgen M (2015) Tribological performance of TiN coatings deposited on 304L stainless steel used for olive-oil extraction. Wear S0043-1648:00384–00381

    Google Scholar 

  11. Massaq A, Rusinek A, Klosak M, Abed F, El M (2016) A study of friction between composite-steel surfaces at high impact velocities. Tribiology Int 102:38–43

    Article  Google Scholar 

  12. Verma PC, Ciudin R, Bonfanti A, Aswath P, Straffelini G, Gialanella S (2016) Role of the friction layer in the high-temperature pin-on-disc study of a brake material. Wear 346–347:56–65

    Article  Google Scholar 

  13. Kiran TS, Prasanna Kumar M, Basavarajappa S, Viswanatha BM (2014) Dry sliding wear behavior of heat treated hybrid metal matrix composite using Taguchi techniques. Mater Des 63:294–304

    Article  Google Scholar 

  14. Baghery P, Farzam M, Mousavi AB, Hosseini M (2010) Ni – TiO2 nanocomposite coating with high resistance to corrosion and wear. Surf Coat Technol 204:3804–3810

    Article  Google Scholar 

  15. Guha D, Roy Chowdhuri SK (1996) The effect of surface roughness on the temperature at the contact between sliding bodies. Wear 197:63–73

    Article  Google Scholar 

  16. Yevtushenko AA, Adamowicz A, Grzes P (2013) Three-dimensional FE model for the calculation of temperature of a disc brake at temperature-dependent coefficients of friction. Int Commun Heat Mass Transf 42:18–24

    Article  Google Scholar 

  17. Wahlström J (2014) A comparison of measured and simulated friction, wear, and particle emission of disc brakes. Wear 313:75–82

    Article  Google Scholar 

  18. Prabhakar NS, Radhika N, Raghu R (2014) Analysis of Tribological Behavior of Aluminium/B4C Composite Under Dry Sliding Motion. Procedia Eng 97:994–1003

    Article  Google Scholar 

  19. Tzanakis I, Conte M, Hadfield M, Stolarski TA (2013) Experimental and analytical thermal study of PTFE composite sliding against high carbon steel as a function of the surface roughness, sliding velocity and applied load. Wear 303:154–168

    Article  Google Scholar 

  20. Shi Y, Yao Y (2014) Test and regression analysis on tribological properties of locomotive traction gear materials. Emerging Materials Research 3

  21. He Y, Huang S (2005) Convection heat and mass transfer from a disk. Heat Mass Transf 41:766–772

    Article  Google Scholar 

  22. Archard JF (1959) The temperature of rubbing surfaces. Wear 2:438–455

    Article  Google Scholar 

  23. Hartnett JP (2016) The Influence of Prandtl Number on the Heat Transfer From Rotating Nonisothermal Disks and Cones. J Heat Transf 95:5–6

    Google Scholar 

  24. Ying S, Yupeng Y (2017) Temperature field analysis of pin-on-disk sliding friction test. Int J Heat Mass Transf 107:339–346

    Article  Google Scholar 

Download references

Acknowledgements

AICTE Sponsored project titled Wear Behaviour of Hybrid Metal Matrix Composites at Varied Temperature. Ref. No.20/AICTE/RIFD/ RPS (Policy-IV) 26/2012-13, Dated: March 18, 2013.

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Government Engineering College, Haveri, Karnataka, India

    C. R. Raghavendra

  2. Indian Institute of Information Technology, IT Park, Dharwad, Hubballi, Karnataka, India

    S. Basavarajappa

  3. University BDT College of Engineering, Davanagere, Karnataka, India

    Irappa Sogalad

Authors
  1. C. R. Raghavendra
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. S. Basavarajappa
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Irappa Sogalad
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to C. R. Raghavendra.

Additional information

Publisher’s Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Raghavendra, C.R., Basavarajappa, S. & Sogalad, I. Analysis of temperature field in dry sliding wear test on pin-on-disc. Heat Mass Transfer 55, 1545–1552 (2019). https://doi.org/10.1007/s00231-018-2524-y

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00231-018-2524-y

Search

Navigation