Abstract
The effects of laser incising on the surface of heat-affected zones (HAZs) and liquid uptake of wood were examined. Deep pin holes were incised on the tangential section of the wood with a laser beam of 1 kW in power with varied pulse widths, and the HAZs of the holes were investigated using scanning electron microscopy. The length of liquid uptake passing through HAZs surfaces was then measured. It was observed that the HAZs were unable to maintain normal porous structure, and smooth surfaces such as that of wood charcoal were also not observed. This is because the composite of the middle lamella completely melted, which led to a decrease in the length of liquid uptake. In addition, the release of high gas-pressure and thermal energy during the laser-incising process did not damage the tylose and the aspirated pit in the longitudinal direction. Because of this, the liquid movement remained blocked. However, the incising holes provided additional liquid-intake points, resulting in greater intake capacity. Moreover, it was observed that improvement of liquid impregnation is related to hole diameter.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Barcikowski S, Koch G, Odermatt J (2006) Characterisation and modification of the heat affected zone during laser material processing of wood and wood composites. Holz Roh- Werkst 64:94–103
Goring DAI (1963) Thermal softening of lignin, hemicellulose and cellulose. Pulp Paper Mag Can 64:517–527
Hattori N (1995) Laser processing of wood. Mokuzai Gakkaishi 41:703–709
Hattori N, Matano T, Okamoto H, Okamura K (1988) Microscopic observations of the solid products deposited on the edge of paper by CO2 laser cutting. Mokuzai Gakkaishi 34:417–422
Iida I, Ikeuchi A, Imamura Y (1995) Liquid penetration of precompressed wood III: effect of compressive deformation and recovery upon liquid uptake. Mokuzai Gakkaishi 41:811–819
Iida I, Yusuf S, Watanabe U, Imamura Y (2002) Liquid penetration of precompressed wood VII: combined treatment of precompression and extraction in hot water on the liquid penetration of wood. J Wood Sci 48:81–85
Islam MN, Ando K, Yamuchi H, Kobayashi Y, Hattori N (2007) Passive impregnation of liquid in impermeable lumber incised by laser. J Wood Sci 53:436–441
Islam MN, Ando K, Yamuchi H, Kobayashi Y, Hattori N (2008) Comparative study between full cell and passive impregnation method of wood preservation for laser incised Doulas fir lumber. Wood Sci Technol 42:343–350
Kuriyama A (1979) A study on the carbonization process of wood. Bull For For Prod Res Inst 304:7–76
Lu JX, Lin ZY, Jiang JH (2005) Liquid penetration of freeze-drying and air-drying wood of plantation Chinese fir. J For Res 16:293–295
Panzner M, Wiedemann G, Henneberg, Fischer R, Wittke Th, Dietsch R (1998) Experimental investigation of laser ablation process on wood surfaces. Appl Surf Sci 127–129:787–792
Yoshizawa N, Andoh M, Ishiguri F, Yokota S, Furuno T (1999) Rupture of pit membranes in Sugi (Cryptomeria japoncia D.Don) logs by a smoke-heating system with increased far-infrared radiation. Holzforschung 53:9–15
Zeriouh A, Belkbir L (1995) Thermal decomposition of a Moroccan wood under nitrogen atmosphere. Thermochim Acta 258:243–248
Acknowledgments
This work was supported by Grants-in-Aid for Scientific Research [(A) 22248019] from the Japan Society for the Promotion of Science (JSPS). The authors wish to thank Professor Junji Sugiyama and Professor Hiroyuki Yano, Research Institute for Sustainable Humanosphere, Kyoto University, Japan, for their valuable comments and for providing SEM equipment.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Wang, Y., Ando, K. & Hattori, N. Changes in the anatomy of surface and liquid uptake of wood after laser incising. Wood Sci Technol 47, 447–455 (2013). https://doi.org/10.1007/s00226-012-0497-4
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00226-012-0497-4