Skip to main content
SpringerLink
Log in

Research on three-dimensional cutting force theoretical model of turning glass–ceramics based on discretization of cutting edge

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Cutting force is one of the most important physical quantities in the cutting process. Cutting force directly determines the generation of cutting heat and affects tool wear and machined surface quality. In this work, based on the geometric analysis of the turning tool, the cutting edge was discretized, and the local parameters of each cutting edge were calculated. According to the formation and assumption of brittle material chips, considering the energy dissipation in the process of chip formation, the cutting force of each cutting edge element was calculated. Then, the theoretical model of three-dimensional turning force of glass–ceramics was established by adding the forces contributed by all cutting edge elements. The change of tool geometry angle can lead to the change of local cutting parameters at each point on the cutting edge, thereby affecting the variation of cutting force. In order to evaluate the cutting force model, the turning experiment of fluormica glass–ceramics was carried out, and the influence of tool geometry angles (normal rake angle γn, tool nose radius rε, and tool cutting edge angle κr) on the cutting force was discussed. The predicted results are in good agreement with the measured results. This model can provide theoretical guidance for the efficient turning strategy of glass–ceramics.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18

Similar content being viewed by others

Data availability

All data generated or analyzed during this study are included in this article.

Code availability

Not applicable.

References

  1. Li C, Li X, Wu Y, Zhang F, Huang H (2019) Deformation mechanism and force modelling of the grinding of YAG single crystals. Int J Mach Tool Manu 143:23–37. https://doi.org/10.1016/j.ijmachtools.2019.05.003

    Article  Google Scholar 

  2. Zhou Y, Tian C, Jia S, Ma L, Yin G, Gong Y (2023) Study on grinding force of two-dimensional ultrasonic vibration grinding 2.5D-C/SiC composite material. Crystals 13:151. https://doi.org/10.3390/cryst13010151

    Article  Google Scholar 

  3. Sun Y, Jin L, Gong Y, Wen X, Yin G, Wen Q, Tang B (2022) Experimental evaluation of surface generation and force time-varying characteristics of curvilinear grooved micro end mills fabricated by EDM. J Manuf Process 73:799–814. https://doi.org/10.1016/j.jmapro.2021.11.049

    Article  Google Scholar 

  4. Parakkal G, Zhu R, Kapoor SG, Devor RE (2002) Modeling of turning process cutting forces for grooved tools. Int J Mach Tool Manu 42:179–191. https://doi.org/10.1016/S0890-6955(01)00121-3

    Article  Google Scholar 

  5. Karakurt I, Aydin G, Aydiner K (2013) Predictive modeling of noise level generated during sawing of rocks by circular diamond sawblades. Sadhana 38:491–511. https://doi.org/10.1007/s12046-013-0117-5

    Article  Google Scholar 

  6. Sambhav K, Kumar A, Choudhury SK (2011) Mechanistic force modeling of single point cutting tool in terms of grinding angles. Int J Mach Tool Manu 51:775–786. https://doi.org/10.1016/j.ijmachtools.2011.06.007

    Article  Google Scholar 

  7. Kaya S, Aydin G, Karakurt I (2023) An experimental study on the cutting depth produced by abrasive waterjet: how do abrasive and rock properties affect the cutting process? Int J Adv Manuf Technol 125:4811–4823. https://doi.org/10.1007/s00170-023-11053-5

    Article  Google Scholar 

  8. Zhang X, Wang J, Han J (2023) Crystallization kinetics, structural and mechanical properties of transparent lithium aluminosilicate glass-ceramics. J Non-Cryst Solids 603:122113. https://doi.org/10.1016/j.jnoncrysol.2022.122113

    Article  Google Scholar 

  9. Joardar H, Das NS, Sutradhar G, Singh S (2014) Application of response surface methodology for determining cutting force model in turning of LM6/SiCP metal matrix composite. Measurement 47:452–464. https://doi.org/10.1016/j.measurement.2013.09.023

    Article  Google Scholar 

  10. Balasubramanian K, Nataraj M, Duraisamy P (2019) Machinability analysis and application of response surface approach on CNC turning of LM6/SiCP composites. Mater Manuf Process 34(12):1389–1400. https://doi.org/10.1080/10426914.2019.1660787

    Article  Google Scholar 

  11. Werner G (1978) Influence of work material on grinding forces. Annals of CIRP 27:243–248

    Google Scholar 

  12. Durgumahanti P, Singh V, Venkateswara P (2010) A new model for grinding force prediction and analysis. Int J Mach Tool Manu 50(3):231–240. https://doi.org/10.1016/j.ijmachtools.2009.12.004

    Article  Google Scholar 

  13. Mishra VK, Salonitis K (2013) Empirical estimation of grinding specific forces and energy based on a modified Werner grinding model. Procedia CIRP 8:287–292. https://doi.org/10.1016/j.procir.2013.06.104

    Article  Google Scholar 

  14. Guo M, Li B, Ding Z, Liang S (2016) Empirical modeling of dynamic grinding force based on process analysis. Int J Adv Manuf Technol 86:3395–3405. https://doi.org/10.1007/s00170-016-8465-z

    Article  Google Scholar 

  15. Limido J, Espinosa C, Salaun M, Lacome J (2007) SPH method applied to high speed cutting modelling. Int J Mech Sci 49:898–908. https://doi.org/10.1016/j.ijmecsci.2006.11.005

    Article  Google Scholar 

  16. Chen M, Jiang W, Li M (2011) Effects of tool edge radius and rake angle on ductile machining process of CaF2. Int J Nanomanuf 7:350–360. https://doi.org/10.1504/ijnm.2011.042476

    Article  Google Scholar 

  17. Zhou T, He L, Zou Z, Du F, Wu J, Tian P (2020) Three-dimensional turning force prediction based on hybrid finite element and predictive machining theory considering edge radius and nose radius. J Manuf Process 58:1304–1317. https://doi.org/10.1016/j.jmapro.2020.09.034

    Article  Google Scholar 

  18. Xiao J, Wang G, Su H, Huang P (2022) Study on cutting force and induced thermal damage of carbon fiber reinforced polymer composites using microscopic simulation modeling. Polym Composite 43:1626–1636. https://doi.org/10.1002/pc.26484

    Article  Google Scholar 

  19. Yu S, Lin B, Han X, Lin B (2002) The application of molecular dynamics simulation technology in the field of ultra precision machining. Chin Mech Eng 13(1):28–31

    Google Scholar 

  20. Duan N, Yu Y, Wang W, Xu X (2016) SPH and FE coupled 3D simulation of monocrystal SiC scratching by single diamond grit. Int J Refract Met H 64:279–293. https://doi.org/10.1016/j.ijrmhm.2016.09.016

    Article  Google Scholar 

  21. Chen H, Cao H, Wu R, Lu C (2019) Modeling and simulation of high-speed cylindrical grinding based on 3D grinding wheel topography. IOP Conf Ser: Mater Sci and Eng 592:012067. https://doi.org/10.1088/1757-899X/592/1/012067

    Article  Google Scholar 

  22. Ding H, Han Y, Zhou K, Huang Y, Shi L, Guo J, Liu Q, Wang W (2020) Grinding force modeling and experimental verification of rail grinding. P I Mech Eng J-J Eng 234(8):1254–1264. https://doi.org/10.1177/1350650119900738

    Article  Google Scholar 

  23. Merchant ME (1945) Mechanics of the metal cutting process. J Appl Phys 16:267–275. https://doi.org/10.1063/1.1707586

    Article  Google Scholar 

  24. Oxley P (1989) Mechanics of machining. Ellis Horwood, Chichester

    Google Scholar 

  25. Poзeнбepт AM, Epeмин AH (1956) Metal cutting theory. Mechanical architecture press of national science and technology department of Soviet Union (in Russian)

  26. Ma L, Yu A, Chen J (2017) Theoretical model of cutting force in turning the lithium disilicate glass-ceramic. Int J Adv Manuf Technol 92:4355–4366. https://doi.org/10.1007/s00170-017-0499-3

    Article  Google Scholar 

  27. Sun J, Qin F, Chen P, An T (2016) A predictive model of grinding force in silicon wafer self-rotating grinding. Int J Mach Tool Manu 109:74–86. https://doi.org/10.1016/j.ijmachtools.2016.07.009

    Article  Google Scholar 

  28. Li H, Yu T, Wang Z, Zhu L, Wang W (2016) Detailed modeling of cutting forces in grinding process considering variable stages of grain-workpiece micro interactions. Int J Mech Sci 126:319–339. https://doi.org/10.1016/j.ijmecsci.2016.11.016

    Article  Google Scholar 

  29. Liu M, Li C, Zhang Y, Yang M, Gao T, Cui X, Wang X, Xu W, Zhou Z, Liu B, Said Z, Li R, Sharma S (2023) Analysis of grinding mechanics and improved grinding force model based on randomized grain geometric characteristics. Chinese J Aeronaut 36:160–193. https://doi.org/10.1016/j.cja.2022.11.005

    Article  Google Scholar 

  30. Gao B, Jin T, Qu M, Li P, Xie G, Shang Z (2024) Force modeling of vertical surface grinding considering wheel-workpiece contact geometry. Int J Mech Sci 269:108999. https://doi.org/10.1016/j.ijmecsci.2024.108999

    Article  Google Scholar 

  31. Che D, Zhu W, Ehmann KF (2016) Chipping and crushing mechanisms in orthogonal rock cutting. Int J Mech Sci 119:224–236. https://doi.org/10.1016/j.ijmecsci.2016.10.020

    Article  Google Scholar 

  32. Nishimatsu Y (1972) The mechanics of rock cutting. Int J Rock Mech Min Sci 9:261–270. https://doi.org/10.1016/0148-9062(72)90027-7

    Article  Google Scholar 

  33. Rubenstein C (1983) The mechanics of continuous chip formation in oblique cutting in the absence of chip distortion. Part 1-theory. Int J Mach Tool Manu 23:11–20. https://doi.org/10.1016/0020-7357(83)90003-3

    Article  Google Scholar 

  34. Li H, Zhang W, Li X (2001) Modelling of cutting forces in helical end milling using a predictive machining theory. Int J Mech Sci 43:1711–1730. https://doi.org/10.1016/S0020-7403(01)00020-0

    Article  Google Scholar 

  35. Roberts DK, Wells AA (1954) The velocity of brittle fracture. Engineering 178(4639):820–821

    Google Scholar 

Download references

Funding

This work was financially supported by the National Natural Science Foundation of China (51975113), the Fundamental Research Funds for the Central Universities (2023GFYD002, N2223012), the Natural Science Foundation of Hebei Province (E2021501027), and the Science and Technology Project of Hebei Education Department (QN2022204).

Author information

Authors and Affiliations

  1. School of Mechanical Engineering & Automation, Northeastern University, Shenyang, 110819, China

    Hongshuang Li, Lianjie Ma, Jinhao Li, Chunyu Dai & Zhibin Han

  2. School of Control Engineering, Northeastern University at Qinhuangdao, Qinhuangdao, 066004, China

    Lianjie Ma, Yunguang Zhou & Ming Li

Authors
  1. Hongshuang Li
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Lianjie Ma
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Jinhao Li
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Chunyu Dai
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Zhibin Han
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Yunguang Zhou
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. Ming Li
    View author publications

    You can also search for this author in PubMed Google Scholar

Contributions

Hongshuang Li: experimental research, methodology, data processing, and writing. Lianjie Ma: financial support for the project leading to this publication. Jinhao Li: software and investigation. Chunyu Dai: software. Zhibin Han: validation. Yunguang Zhou: supervision. Ming Li: supervision.

Corresponding author

Correspondence to Lianjie Ma.

Ethics declarations

Competing interests

The authors declare no competing interests.

Ethics approval

This paper does not contain any studies with human participants or animals performed by any of the authors.

Consent to participate

All of the authors consent to participate.

Consent for publication

All of the authors consent for publication.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Li, H., Ma, L., Li, J. et al. Research on three-dimensional cutting force theoretical model of turning glass–ceramics based on discretization of cutting edge. Int J Adv Manuf Technol 132, 1809–1825 (2024). https://doi.org/10.1007/s00170-024-13462-6

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-024-13462-6

Keywords

Search

Navigation