Abstract
The AFRP (aramid fiber reinforced polymer) material’s finite element model is built using ABAQUS software for resin and aramid fiber based on the Johnson–Cook failure and Hashin failure criterion. The effects of feed rate and hole diameter on axial force and fiber layer displacement are determined by the simulation study of milling holes. It was possible to decide on the delamination force and produce the fiber layer displacement curve by measuring the delamination force of aramid fiber composites with various layer thicknesses and hole diameters. Elastic deformation, linear loading delamination, severe failure delamination, and stability failure delamination were classified into four phases. The geometric model for Tool-AFRP hole machining is created. The functional connection between delamination force and fiber layer displacement is obtained from the model’s axial force production process. The Kistler9129AA dynamometer is used to conduct the hole machining experiment. Analysis of the variation law of the hole machining axial force under the aforementioned influencing elements, as well as the impacts of feed speed, hole diameter, and processing method, further demonstrates the accuracy of the geometric model, the variation law of the delamination force and fiber layer displacement in the test agrees with the derivation above.
Similar content being viewed by others
References
Xu JY, Mkaddem A, El Mansori M (2016) Recent advances in drilling hybrid FRP/Ti composite: a state-of-the-art review. Compos Struct 135:316–338. https://doi.org/10.1016/j.compstruct.2015.09.028
Shetty N, Shahabaz SM, Sharma SS, Divakara SS (2017) A review on finite element method for machining of composite materials. Compos Struct 176:790–802. https://doi.org/10.1016/j.compstruct.2017.06.012
Geng DX, Liu YH, Shao ZY, Lu ZH, Cai J, Li X, Jiang XG, Zhang DY (2019) Delamination formation, evaluation and suppression during drilling of composite laminates: a review. Compos Struct 216:168–186. https://doi.org/10.1016/j.compstruct.2019.02.099
Wan M, Li SE, Yuan H, Zhang WH (2019) Cutting force modelling in machining of fiber-reinforced polymer matrix composites (PMCs): a review. Compos A Appl Sci Manuf 117:34–55. https://doi.org/10.1016/j.compositesa.2018.11.003
Ismail SO, Dhakal HN, Dimla E, Popov I (2017) Recent advances in twist drill design for composite machining: a critical review. Proc Inst Mech Eng B J Eng Manuf 231:2527–2542. https://doi.org/10.1177/0954405416635034
Khashaba UA, El-Sonbaty IA, Selmy AI, Megahed AA (2010) Machinability analysis in drilling woven GFR/epoxy composites: part II - Effect of drill wear. Compos A-Appl Sci Manuf 41:1130–1137. https://doi.org/10.1016/j.compositesa.2010.04.011
Kumar M, Kumar P, Bhadauria SS (2020) Interlaminar fracture toughness and fatigue fracture of continuous fiber-reinforced polymer composites with carbon-based nanoreinforcements: a review. Polymer-Plast Technol Mater 59:1041–1076. https://doi.org/10.1080/25740881.2020.1719142
Jain S, Yang DCH (1993) Effects of feedrate and chisel edge on delamination in composites drilling. J Eng Ind 115:398–405. https://doi.org/10.1115/1.2901782
Thakur A, Singh A, Sharma M (2021) Mechanics of delamination-free drilling in polymer matrix composite laminates: a review. Proc IME C J Mech Eng Sci 235:136–160. https://doi.org/10.1177/0954406220934828
Liu DF, Tang YJ, Cong WL (2012) A review of mechanical drilling for composite laminates. Compos Struct 94:1265–1279. https://doi.org/10.1016/j.compstruct.2011.11.024
Rajakumar IPT, Hariharan P, Vijayaraghavan L (2012) Drilling of carbon fibre reinforced plastic (CFRP) composites - a review. Int J Mater Prod Technol 43:43–67. https://doi.org/10.1504/IJMPT.2012.047647
Xu WX, Zhang LC, Wu YB (2014) Elliptic vibration-assisted cutting of fibre-reinforced polymer composites: understanding the material removal mechanisms. Compos Sci Technol 92:103–111. https://doi.org/10.1016/j.compscitech.2013.12.011
Wang HJ, Dong HY, Ke YG, Sun J (2019) Modeling and analysis of force prediction in milling process of unidirectional fiber reinforced polymer composites. Int J Adv Manuf Technol 101:3073–3080. https://doi.org/10.1007/s00170-018-3056-9
Zhang YF, Liu D, Zhang WJ, Zhu HT, Huang CZ (2021) Damage study of fiber-reinforced composites drilled by abrasive waterjet -challenges and opportunities. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-021-08246-1
Kim W, Lim SH, Kang D, Bae S, On SY, Kim SS (2021) Research trends and future perspective in nonconventional machining of fiber-reinforced polymers: a review. Funct Compos Struct 3.https://doi.org/10.1088/2631-6331/ac0c28
Sorrentino L, Turchetta S, Bellini C (2018) A new method to reduce delaminations during drilling of FRP laminates by feed rate control. Compos Struct 186:154–164. https://doi.org/10.1016/j.compstruct.2017.12.005
Tyczyński P, Lemańczyk J, Ostrowski R, Ewa R (2014) Drilling of CFRP, GFRP, glare type composites. Aircr Eng Aerosp Technol 86:312–322. https://doi.org/10.1108/AEAT-10-2012-0196
Liu SN, Yang T, Liu C, Jin Y, Sun D, Shen YF (2020) Modelling and experimental validation on drilling delamination of aramid fiber reinforced plastic composites. Compos Struct 236:111907. https://doi.org/10.1016/j.compstruct.2020.111907
Ali M, Ibrahim D, Mohamed EM (2008) A micro–macro combined approach using FEM for modelling of machining of FRP composites: cutting forces analysis. Compos Sci Technol 68:3123–3127. https://doi.org/10.1016/j.compscitech.2008.07.009
Cepero F, Curiel JL, Blazquez A, Yu TT, Kerrigan K, Phadnis VA (2020) Review of recent developments and induced damage assessment in the modelling of the machining of long fibre reinforced polymer composites. Compos Struct 240.https://doi.org/10.1016/j.compstruct.2020.112006
Yang ZC, Yang FJ, Xiao JM, Yuan ZY, Li Y (2019) Establishment of finite element model for milling CFRP and simulation analysis of cutting forces. Aerospace Mater Technol 49:36–40. https://doi.org/10.12044/j.issn.1007-2330.2019.03.007
He YL, Li L, Wan M, Xue HQ (2022) Three-dimensional finite element simulations of milling carbon/epoxy composites. Compos Struct 282:115037. https://doi.org/10.1016/j.compstruct.2021.115037
Jia BH, Li G, Xu ZY, Guo LJ (2018) Numerical simulation on the behaviour of aramid fiber laminates normally impacted by projectiles. J Vibration Shock 37:157–161. https://doi.org/10.13465/j.cnki.jvs.2018.06.025
Karpat Y, Değer B, Bahtiyar O (2014) Experimental evaluation of polycrystalline diamond tool geometries while drilling carbon fiber-reinforced plastics. Int J Adv Manuf Technol 71:1295–1307. https://doi.org/10.1007/s00170-013-5592-7
Jenarthanan MP, Jeyapaul R, Kumar SR (2017) Comparative analysis of delamination factor prediction using RSM and ANN during endmilling of GFRP composites. Aust J Mech Eng 15:111–124. https://doi.org/10.1080/14484846.2015.1093682
Xu WX, Zhang LC (2014) On the mechanics and material removal mechanisms of vibration-assisted cutting of unidirectional fibre-reinforced polymer composites. Int J Mach Tools Manuf 80–81:1–10. https://doi.org/10.1016/j.ijmachtools.2014.02.004
Ismail SO, Ojo SO, Dhakal HN (2017) Thermo-mechanical modelling of FRP cross-ply composite laminates drilling: delamination damage analysis. Compos Part B Eng 108:45–52. https://doi.org/10.1016/j.compositesb.2016.09.100
Wang FJ, Zhao MY, Yan JB, Qiu S, Liu X, Zhang BY (2020) Investigation of damage reduction when dry-drilling aramid fiber-reinforced plastics based on a three-point step drill. Materials 13. https://doi.org/10.3390/ma13235457
Acknowledgements
This work was supported by grant 51975006 from the National Natural Science Foundation of China.
The authors gratefully acknowledge their financial support.
Funding
This research was funded by the National Natural Science Foundation of China grant number 51975006.
Author information
Authors and Affiliations
Contributions
Wentian Shi: data curation, formal analysis, writing—original draft, writing—review, and editing. Tianming Yan: data curation, formal analysis, methodology, writing—original draft, and writing review editing. Yude Liu: investigation, resources, supervision, writing—review, and editing. Lin Wang: investigation, resources, supervision, writing—review and editing. Lu Dong: data curation, validation, and visualization. Chuan Xie: data curation, validation, and visualization.
Corresponding author
Ethics declarations
Conflict of interest
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Research data
The raw/processed data required to reproduce these findings cannot be shared as the data also forms part of an ongoing study.
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Shi, W., Yan, T., Liu, Y. et al. Simulation analysis of aramid fiber reinforced polymer hole machining and experimental study on delamination mechanism. Int J Adv Manuf Technol 125, 417–433 (2023). https://doi.org/10.1007/s00170-022-10645-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-022-10645-x