Abstract
Ceramic rock slab is a kind of new material with the advantages of high hardness, wear resistance, and high-temperature resistance, and it is widely used in industry and households. However, problems such as easy chipping and serious tool wearing occurred in conventional grinding (CG). To overcome these challenges, this work introduces rotary ultrasonic grinding (RUG) in processing ceramic rock slabs. Study the theoretical motion trajectory of single abrasive grain and the removal mechanism of hard and brittle materials in RUG, and analyzed the influence of amplitude on cutting force in finite element simulation of single abrasive grain. A comparative process experiment of RUG and CG was performed on the hole processing of ceramic rock slabs. The experimental results showed that compared with CG, the cutting force and chipping area of RUG were reduced by 40.4 and 14.3%, respectively. The cutting force and chipping area decreased with the increase of the spindle speed and increased with the increase of the feed speed. With the increase of ultrasonic amplitude, the cutting force and chipping area decreased gradually, and the tool wear rate decreased from 0.54 to 0.10%, which effectively suppresses the spalling of abrasive grains on the surface of the tool and extends the life of the tool.
Similar content being viewed by others
References
L JY, He LC (2020) Talking about ceramic rock slab products[J]. Stone (04):17–20.
Wang JJ, Feng PF, Zhang JF, Zhang CL, Pei ZJ (2016) Modeling the dependency of edge chipping size on the material properties and cutting force for rotary ultrasonic drilling of brittle materials[J]. Int J Mach Tools Manuf 101:18–27
Wang JJ, Feng PF, Zheng JZ, Zhang JF (2016) Improving hole exit quality in rotary ultrasonic machining of ceramic matrix composites using a compound step-taper drill[J]. Ceram Int 42:13387–13394
Chen HH (2021) Development of rotary ultrasonic machining toolholder and experimental study of rock slab drilling process[D]. Guangdong University of Techno
Dong GJ, Gao SD, Wang L (2022) Three dimensional shape model of TiBw mesh reinforced titanium matrix composites in rotary ultrasonic grinding[J]. J Manuf Process 75:682–692
Chen YR, Su HH, He JY, Qian N, Gu JQ, Xu JH, Ding K (2021) The effect of torsional vibration in longitudinal–torsional coupled ultrasonic vibration-assisted grinding of silicon carbide ceramics[J]. Materials 14(3):688
Wang H, Pei ZJ, Cong WL (2020) A mechanistic cutting force model based on ductile and brittle fracture material removal modes for edge surface grinding of CFRP composites using rotary ultrasonic machining[J]. International Journal of Mechanical Sciences
Pujana J, Rivero A, Celaya A et al (2009) Analysis of ultrasonic-assisted drilling of Ti6Al4V[J]. Int J Mach Tools Manuf 49(6):500–508
Wang JJ, Feng PF, Zhang JF, Guo P (2018) Reducing cutting force in rotary ultrasonic drilling of ceramic matrix composites with longitudinal-torsional coupled vibration[J]. Manufacturing Letters 18:1–5
Liu JW, Baek DK, Ko TJ (2014) Chipping minimization in drilling ceramic materials with rotary ultrasonic machining[J]. Int J Adv Manuf Technol 72(9–12):1527–1535
Dong S, Liao WH, Zheng K, Liu JS, Feng JD (2019) Investigation on exit burr in robotic rotary ultrasonic drilling of CFRP/aluminum stacks[J]. Int J Mech Sci 151:868–876
Sanda A, Arriola I, Garcia Navas V, Bengoetxea I, Gonzalo O (2016) Ultrasonically assisted drilling of carbon fibre reinforced plastics and Ti6Al4V[J]. J Manuf Process 22:169–176
Amini S, Baraheni M, Mardiha A (2018) Parametric investigation of rotary ultrasonic drilling of carbon fiber reinforced plastics[J]. Proc Inst Mech Eng Part E: J Process Mech Eng 232(5):540–554
Baraheni M, Amini S (2019) Investigation on rotary ultrasonic assisted end grinding of silicon nitride ceramics[J]. SN Applied Sciences 1(12).
Peng ZJ, Zhang DY, Zhang X (2020) Chatter stability and precision during high-speed ultrasonic vibration cutting of a thin-walled titanium cylinder[J]. Chin J Aeronaut 33(12):3535–3549
Agarwal S, Venkateswara RP (2013) Predictive modeling of force and power based on a new analytical undeformed chip thickness model in ceramic grinding[J]. Int J Mach Tools Manuf 65:68–78
Li Z, Yuan SM, Ma J, Shen J, Batako A (2022) Cutting force and specific energy for rotary ultrasonic drilling based on kinematics analysis of vibration effectiveness[J]. Chin J Aeronaut 35(1):376–387
Dong GJ, Zhang LM (2019) Investigation on grinding force and machining quality during rotary ultrasonic grinding deep-small hole of fluorophlogopite ceramics[J]. Int J Adv Manuf Technol 104(5–8):2815–2825
Wang Y, Lin B, Cao XY, Wang SL (2014) An experimental investigation of system matching in ultrasonic vibration assisted grinding for titanium[J]. J Mater Process Technol 214(9):1871–1878
Shi ZL, Xiang DH, Feng HR, Wu BF, Zhang ZM, Gao ZF, Zhao B (2021) Finite element and experimental analysis of ultrasonic vibration milling of high-volume fraction SiCp/Al composites[J]. Int J Precis Eng Manuf 22(10):1777–1789
Liu DF, Cong WL, Pei ZJ, Tang YJ (2012) A cutting force model for rotary ultrasonic machining of brittle materials[J]. Int J Mach Tools Manuf 52(1):77–84
Feng Y, Hsu FC, Lu YT, Lin YF, Lin CT, Lin CF, Lu YC (2020) Force prediction in ultrasonic vibration-assisted milling[J]. Mach Sci Technol 25(2):307–330
Feng Y, Hsu FC, Lu YT, Lin YF, Lin CT, Lin CF, Lu YC (2020) Tool wear rate prediction in ultrasonic vibration-assisted milling[J]. Mach Sci Technol 24(5):758–780
Li ZC, Jiao Y, Deines TW, Pei ZJ, Treadwell C (2005) Rotary ultrasonic machining of ceramic matrix composites: feasibility study and designed experiments[J]. Int J Mach Tools Manuf 45(12–13):1402–1411
Liang ZQ, Wu YB, Wang XB, Zhao WX (2010) A new two-dimensional ultrasonic assisted grinding (2D-UAG) method and its fundamental performance in monocrystal silicon machining[J]. Int J Mach Tools Manuf 50(8):728–736
Chen YR, Su HH, Qian N, He JY, Gu JQ, Xu JH, Ding K (2021) Ultrasonic vibration-assisted grinding of silicon carbide ceramics based on actual amplitude measurement: grinding force and surface quality[J]. Ceram Int 47(11):15433–15441
Qin N, Pei ZJ. Treadwell C, Guo DM (2009) Physics-based predictive cutting force model in ultrasonic- vibration-assisted grinding for titanium drilling[J]. Journal of Manufacturing Science and Engineering ASME (131):111–119
Xiao XZ, Zheng K, Liao WH (2014) Theoretical model for cutting force in rotary ultrasonic milling of dental zirconia ceramics[J]. Int J Adv Manuf Technol 75(9–12):1263–1277
Zhang QH, Wu CL, Sun JL, Jia ZX (2000) The mechanism of material removal in ultrasonic drilling of engineering ceramics[J]. Proc Inst Mech Eng Part B J Eng Manuf 214(9):805–810
Amin M, Yuan SM, Khan MZ, Wu Q, Zhu GY (2017) Development of a generalized cutting force prediction model for carbon fiber reinforced polymers based on rotary ultrasonic face milling[J]. Int J Adv Manuf Technol 93(5–8):2655–2666
Wang JJ, Feng PF, Zhang JF, Cai WC, Shen H (2017) Investigations on the critical feed rate guaranteeing the effectiveness of rotary ultrasonic machining[J]. Ultrasonics 74:81–88
Lu YL, Yuan SM, Chen YX (2019) A cutting force model based on kinematic analysis in longitudinal and torsional ultrasonic vibration drilling[J]. Int J Adv Manuf Technol 104(1–4):631–643
Wang JJ, Feng PF, Zhang JF, Guo P (2018) Experimental study on vibration stability in rotary ultrasonic machining of ceramic matrix composites: cutting force variation at hole entrance[J]. Ceram Int 44(12):14386–14392
Jiao F (2008) Theoretical and experimental studies on ultrasonic aided high efficiency lapping with solid abrasive of engineering ceramics[D]. Shanghai Jiao Tong University
Cong WL, Pei ZJ, Sun X, Zhang CL (2014) Rotary ultrasonic machining of CFRP: a mechanistic predictive model for cutting force[J]. Ultrasonics 54(2):663–675
Bello I, Chong YM, Leung KM, Chan CY, Ma KL (2005) Cubic boron nitride films for industrial applications[J]. Diam Relat Mater 14(11–12):1784–1790
Funding
This work was supported by the Key Scientific and Technological Project of Foshan (no. 2120001009458) and the National Natural Science Foundation of China (no. 51705088).
Author information
Authors and Affiliations
Contributions
Gang Zheng: Conceived the study and wrote the manuscript. Yu Deng: Supervision, writing reviews, and editing. Jianzhou Cai: Software and investigation. Yongjun Zhang: Supervision, resources, and methodology. Guixian Liu: Supervisions on experimentation and experimental data discussion. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Ethical approval
All authors confirm that they follow all ethical guidelines.
Consent to participate
Not applicable.
Consent for publication
Not applicable.
Competing interests
The authors declare that no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Zheng, G., Deng, Y., Cai, J. et al. Study on cutting performance of ceramic rock slab machined by rotating ultrasonic vibration. Int J Adv Manuf Technol 123, 3901–3915 (2022). https://doi.org/10.1007/s00170-022-10489-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-022-10489-5