Skip to main content
Log in

Quantitative influences of successive reuse on thermal decomposition, molecular evolution, and elemental composition of polyamide 12 residues in selective laser sintering

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Since its addition to additive manufacturing (AM), polyamide 12 has dominated the selective laser sintering (SLS) market, thanks to its stable thermal property and high mechanical quality. However, substantial un-sintered residue powders lead to economic losses and are burdensome to the environment. Though several works have reported the aging mechanism and reusability of the polyamide 12 residues in SLS, the quantitative degradation and decomposition changes of differently reused polyamide 12 are not available. This work experiments successive reuse of polyamide 12 residues and quantitatively monitors the thermal decomposition, molecular evolution, and compositional changes of the material in SLS AM. To understand the characteristics of such changes, we reused the same bucket of polyamide 12 powders up to 8 times, collected powder samples, and printed 3- and 32-layer part samples. Our tests revealed that the basic flowability energies per reuse are reduced by 9.90, 15.59, and 12.74 mJ in the 2-, 5-, and 8-time reused powders, respectively. These values are essential to control the flowability of polyamide 12. Laser and heat lower the material onset decomposition temperatures, making the material more labile at a decreased temperature after reuse. On the other hand, the nitrogen atmosphere delays the onset of thermal decomposition to a higher temperature. The 1H NMR spectra reveal the degradation of polyamide 12 with reuse: in polyamide 12 parts 3D-printed using 8-time reused powders, the relative area of the peak on C-H bonds adjacent to nitrogen has a 50% reduction compared to parts using new powders. The carbon deposit and degradation raise the atomic percentages of C and O by 72.49% and 7.13%, respectively, from new powders to the part printed using 8-time reused powders. This study further reveals the surface carbon deposit of polyamide 12 during successive reuse of SLS and explains the effect of laser in inducing polymer decomposition apart from high temperatures.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15

Similar content being viewed by others

Data availability

Not applicable.

Code availability

Not applicable.

References

  1. Ngo TD, Kashani A, Imbalzano G, Nguyen KT, Hui D (2018) Additive manufacturing (3D printing): a review of materials, methods, applications and challenges. Compos Part B 143:172–196

    Article  Google Scholar 

  2. Parandoush P, Lin D (2017) A review on additive manufacturing of polymer-fiber composites. Compos Struct 182:36–53

    Article  Google Scholar 

  3. Ligon SC, Liska R, Stampfl JR, Gurr M, Mülhaupt R (2017) Polymers for 3D printing and customized additive manufacturing. Chem Rev 117(15):10212–10290

    Article  Google Scholar 

  4. Singh S, Sharma V, Sachdeva A (2016) Progress in selective laser sintering using metallic powders: a review. Mater Sci Technol 32(8):760–772

    Google Scholar 

  5. Goodridge R, Tuck C, Hague R (2012) Laser sintering of polyamides and other polymers. Prog Mater Sci 57(2):229–267

    Article  Google Scholar 

  6. Kruth J-P, Wang X, Laoui T, Froyen L (2003) Lasers and materials in selective laser sintering. Assem Autom 23:357–371

    Article  Google Scholar 

  7. McAlea K (1997) Materials and applications for the selective laser sintering, Process 7th International Conference on Rapid Prototyping, pp. 23-33

  8. Xu Z, Wang Y, Wu D, Ananth KP, Bai J (2019) The process and performance comparison of polyamide 12 manufactured by multi jet fusion and selective laser sintering. J Manuf Process 47:419–426

    Article  Google Scholar 

  9. Hawkins WL (1984) Polymer degradation, polymer degradation and stabilization, Springer, pp. 3–34.

  10. Feng L, Wang Y, Wei Q (2019) PA12 Powder Recycled from SLS for FDM. Polymers 11(4):727

    Article  Google Scholar 

  11. Pham DT, Dotchev K, Yusoff W (2008) Deterioration of polyamide powder properties in the laser sintering process. Proc Inst Mech Eng C J Mech Eng Sci 222(11):2163–2176

    Article  Google Scholar 

  12. Dotchev K, Yusoff W (2009) Recycling of polyamide 12 based powders in the laser sintering process. Rapid Prototyp J 15:192–203

    Article  Google Scholar 

  13. Paolucci F, van Mook M, Govaert L, Peters G (2019) Influence of post-condensation on the crystallization kinetics of PA12: from virgin to reused powder. Polymer 175:161–170

    Article  Google Scholar 

  14. DePalma K, Walluk M, Murtaugh A, Hilton J, McConky S, Hilton B (2020) Assessment of 3D printing using fused deposition modeling and selective laser sintering for a circular economy. J Clean Prod 121567

  15. Wegner A, Mielicki C, Grimm T, Gronhoff B, Witt G, Wortberg J (2014) Determination of robust material qualities and processing conditions for laser sintering of polyamide 12. Polym Eng Sci 54(7):1540–1554

    Article  Google Scholar 

  16. Chen P, Tang M, Zhu W, Yang L, Wen S, Yan C, Ji Z, Nan H, Shi Y (2018) Systematical mechanism of polyamide-12 aging and its micro-structural evolution during laser sintering. Polym Test 67:370–379

    Article  Google Scholar 

  17. Gornet T, Davis K, Starr T, Mulloy K (2002) Characterization of selective laser sintering™ materials to determine process stability 546, 2002 International Solid Freeform Fabrication Symposium

  18. Kuehnlein F, Drummer D, Rietzel D, Seefried A (2010) Degradation behavior and material properties of PA 12 plastic powders processed by powder based additive manufacturing technologies

  19. Wudy K, Drummer D, Kühnlein F, Drexler M (2014) Influence of degradation behavior of polyamide 12 powders in laser sintering process on produced parts, AIP Conference Proceedings, American Institute of Physics, pp 691–695

  20. Zarringhalam H, Hopkinson N, Kamperman N, De Vlieger J (2006) Effects of processing on microstructure and properties of SLS nylon 12. Mater Sci Eng A 435:172–180

    Article  Google Scholar 

  21. Yusoff W, Thomas A (2008) The effect of employing an effective laser sintering scanning strategy and energy density value on eliminating “orange peel” on a selective laser sintered part. Int Assoc ManagTechnol

  22. Way Y, Pham D, Dotchev K (2014) Investigation of the thermal properties of different grades polyamide 12 (PA12) in improving laser sintering process (SLS), Applied Mechanics and Materials, Trans Tech Publ, pp. 294-296.

  23. Mägi P, Krumme A, Pohlak M (2016) Recycling of PA-12 in Additive manufacturing and the improvement of its mechanical properties, Key Engineering Materials, Trans Tech Publ, pp. 9-14.

  24. Wang L, Kiziltas A, Mielewski DF, Lee EC, Gardner DJ (2018) Closed-loop recycling of polyamide12 powder from selective laser sintering into sustainable composites. J Clean Prod 195:765–772

    Article  Google Scholar 

  25. Dadbakhsh S, Verbelen L, Verkinderen O, Strobbe D, Van Puyvelde P, Kruth J-P (2017) Effect of PA12 powder reuse on coalescence behaviour and microstructure of SLS parts. Eur Polym J 92:250–262

    Article  Google Scholar 

  26. Hofland EC, Baran I, Wismeijer DA (2017) Correlation of process parameters with mechanical properties of laser sintered PA12 parts, Advances in materials science and engineering 2017

  27. Salmoria G, Lauth V, Cardenuto M, Magnago R (2018) Characterization of PA12/PBT specimens prepared by selective laser sintering. Opt Laser Technol 98:92–96

    Article  Google Scholar 

  28. Król-Morkisz K, Pielichowska K (2019) Thermal decomposition of polymer nanocomposites with functionalized nanoparticles, Polymer Composites with Functionalized Nanoparticles, Elsevier, pp. 405–435

  29. Gavezzotti A (1995) Molecular symmetry, melting temperatures and melting enthalpies of substituted benzenes and naphthalenes. J Chem Soc Perkin Trans 2(7):1399–1404

    Article  Google Scholar 

  30. Pezzin G, Zilio-Grandi F, Sanmartin P (1970) The dependence of the glass transition temperature on molecular weight for polyvinylchloride. Eur Polym J 6(7):1053–1061

    Article  Google Scholar 

  31. Kwei T, Pearce EM, Pennacchia JR, Charton M (1987) Correlation between the glass transition temperatures of polymer mixtures and intermolecular force parameters. Macromolecules 20(5):1174–1176

    Article  Google Scholar 

  32. Naumis GG (2006) Glass transition phenomenology and flexibility: an approach using the energy landscape formalism. J Non-Cryst Solids 352(42-49):4865–4870

    Article  Google Scholar 

  33. Silberman A, Raninson E, Dolgopolsky I, Kenig S (1995) The effect of pigments on the crystallization and properties of polypropylene. Polym Adv Technol 6(10):643–652

    Article  Google Scholar 

  34. Huda M, Drzal L, Ray D, Mohanty A, Mishra M (2008) Natural-fiber composites in the automotive sector, Properties and performance of natural-fibre composites, Elsevier, pp. 221-268

  35. Pinal R (2004) Effect of molecular symmetry on melting temperature and solubility. Org Biomol Chem 2(18):2692–2699

    Article  Google Scholar 

  36. Li R, Hu X (1998) Study on discoloration mechanism of polyamide 6 during thermo-oxidative degradation. Polym Degrad Stab 62(3):523–528

    Article  Google Scholar 

  37. Gijsman P, Tummers D, Janssen K (1995) Differences and similarities in the thermooxidative degradation of polyamide 46 and 66. Polym Degrad Stab 49(1):121–125

    Article  Google Scholar 

  38. R. Ningthoujam (2017) Synthesis and characterization of borides, carbides, and nitrides and their applications, Materials under extreme conditions, Elsevier, pp. 337-375

Download references

Acknowledgements

This work was supported in part by a research grant from Xerox and by National Science Foundation Award #1953155.

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Xu Chen.

Ethics declarations

Competing interests

The authors declare no competing interests.

Additional information

Publisher’s note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Yang, F., Schnuerch, A. & Chen, X. Quantitative influences of successive reuse on thermal decomposition, molecular evolution, and elemental composition of polyamide 12 residues in selective laser sintering. Int J Adv Manuf Technol 115, 3121–3138 (2021). https://doi.org/10.1007/s00170-021-07368-w

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-021-07368-w

Keywords

Navigation