Skip to main content
SpringerLink
Log in

Predicting cutting force with unequal division parallel-sided shear zone model for orthogonal cutting

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Predicting cutting force is always the research hotspot due to its significant effect on machining process. In this work, an analytical model of cutting force based on unequal division parallel-sided shear zone has been developed for orthogonal cutting. An unequal division parallel-sided shear model together with a prediction model of shear angle are integrated into the shear cutting force model in the primary shear zone. The classical Waldrof’s slip-line model is employed to describe the plow effect induced by edge radius of cutter and then the plow cutting force is calculated. The modeling algorithm of cutting force is subsequently proposed by integrating the shear cutting force with the plow cutting force. Cylindrical turning of Inconel 718 alloy is taken as a case to verify the proposed prediction model of cutting force. The measured results show that the predicted cutting force agrees well with the measured value. The average prediction errors of the main cutting force and the feed force are 8.39% and 12.03%, respectively. Compared with the classical shear models, it is found that the developed cutting force model shows higher accuracy on predicting cutting force. Additionally, the proposed model is then further verified by predicting cutting force with five different J-C constitutive models.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8

Similar content being viewed by others

References

  1. Zhou J, Ren J, Yao C (2017) Multi-objective optimization of multi-axis ball-end milling Inconel 718 via grey relational analysis coupled with RBF neural network and PSO algorithm. Measurement 102:271–285. https://doi.org/10.1016/j.measurement.2017.01.057

    Article  Google Scholar 

  2. Germain D, Fromentin G, Poulachon G, Bissey-Breton S (2013) From large-scale to micromachining: a review of force prediction models. J Manuf Process 15(3):389–401. https://doi.org/10.1016/j.jmapro.2013.02.006

    Article  Google Scholar 

  3. Merchant ME (1945) Mechanics of the metal cutting process. I. Orthogonal cutting and a type 2 chip. J Appl Phys 16(5):267–275

    Article  Google Scholar 

  4. Merchant ME (1945) Mechanics of the metal cutting process. II. Plasticity conditions in orthogonal cutting. J Appl Phys 16(6):318–324

    Article  Google Scholar 

  5. Lee EH, Shaffer BW (1951) The theory of plasticity applied to a problem of machining. In. pp 405–413

  6. Fang N (2003) Slip-line modeling of machining with a rounded-edge tool—part I: new model and theory. J Mech Phys Solids 51(4):715–742. https://doi.org/10.1016/S0022-5096(02)00060-1

    Article  MATH  Google Scholar 

  7. Uysal A, Altan E (2014) A new slip-line field modeling of orthogonal machining with a rounded-edge worn cutting tool. Mach Sci Technol 18(3):386–423

    Article  Google Scholar 

  8. Tounsi N, Vincenti J, Otho A, Elbestawi MA (2002) From the basic mechanics of orthogonal metal cutting toward the identification of the constitutive equation. Int J Mach Tools Manuf 42:1373–1383

    Article  Google Scholar 

  9. Oxley PLB (1989) The mechanics of machining: an analytical approach to assessing machinability, Ellis Horwood series in mechanical engineering. Ellis Horwood, Chichester

    Google Scholar 

  10. Adibi-Sedeh AH, Madhavan V, Bahr B (2003) Extension of Oxley’s analysis of machining to use different material models. J Manuf Sci Eng 125(4):656. https://doi.org/10.1115/1.1617287

    Article  Google Scholar 

  11. Lalwani D, Mehta N, Jain P (2009) Extension of Oxley’s predictive machining theory for Johnson and Cook flow stress model. J Mater Process Technol 209(12):5305–5312

    Article  Google Scholar 

  12. Pan Z, Shih DS, Tabei A, Garmestani H, Liang SY (2017) Modeling of Ti-6Al-4V machining force considering material microstructure evolution. Int J Adv Manuf Technol:1–8. https://doi.org/10.1007/s00170-016-9964-7

  13. Pang L, Kishawy H (2012) Modified primary shear zone analysis for identification of material mechanical behavior during machining process using genetic algorithm. J Manuf Sci Eng 134(4):041003-041001-041011

    Article  Google Scholar 

  14. Zhou J, Ren J, Feng Y, Tian W, Shi K (2017) A modified parallel-sided shear zone model for determining material constitutive law. Int J Adv Manuf Technol 91(1):589–603. https://doi.org/10.1007/s00170-016-9717-7

    Article  Google Scholar 

  15. Tr Ö, Zeren E (2006) A methodology to determine work material flow stress and tool-chip interfacial friction properties by using analysis of machining. J Manuf Sci Eng 128(1):119–129. https://doi.org/10.1115/1.2118767

    Article  Google Scholar 

  16. Li B, Wang X, Hu Y, Li C (2011) Analytical prediction of cutting forces in orthogonal cutting using unequal division shear-zone model. Int J Adv Manuf Technol 54(5–8):431–443. https://doi.org/10.1007/s00170-010-2940-8

    Article  Google Scholar 

  17. Chen Y, Li H, Wang J (2015) Further development of Oxley’s predictive force model for orthogonal cutting. Mach Sci Technol 19(1):86–111. https://doi.org/10.1080/10910344.2014.991026

    Article  Google Scholar 

  18. Boothroyd G (1963) Temperatures in orthogonal metal cutting. Proc Inst Mech Eng 177(1):789–810

    Article  Google Scholar 

  19. Shan C, Zhang X, Shen B, Zhang D (2019) An improved analytical model of cutting temperature in orthogonal cutting of Ti6Al4V. Chin J Aeronaut. https://doi.org/10.1016/j.cja.2018.12.001

  20. Mathew P, Oxley PLB (1982) Predicting the effects of very high cutting speeds on cutting forces, etc. CIRP Ann 31(1):49–52. https://doi.org/10.1016/S0007-8506(07)63267-3

    Article  Google Scholar 

  21. Markopoulos AP (2013) Finite element method in machining processes. Springer, London

    Book  Google Scholar 

  22. Toropov A, Ko S-L (2007) Prediction of shear angle for continuous orthogonal cutting using thermo-mechanical constants of work material and cutting conditions. J Mater Process Technol 182(1):167–173. https://doi.org/10.1016/j.jmatprotec.2006.07.027

    Article  Google Scholar 

  23. Liang S, Shih AJ (2016) Analysis of machining and machine tools. Springer, New York

    Book  Google Scholar 

  24. Ueda N, Matsuo T, Hoshi T (1986) An investigation of some shear angle theories. CIRP Ann 35(1):27–30. https://doi.org/10.1016/S0007-8506(07)61831-9

    Article  Google Scholar 

  25. Liang S, Shih AJ (2015) Analysis of machining and machine tools. Springer, New York

    Google Scholar 

  26. Waldorf DJ, DeVor RE, Kapoor SG (1998) A slip-line field for ploughing during orthogonal cutting. J Manuf Sci Eng 120(4):693–699. https://doi.org/10.1115/1.2830208

    Article  Google Scholar 

  27. Waldorf DJ (1996) Shearing, ploughing, and wear in orthogonal machining. University of Illinois at Urbana-Champaign, Illinois

    Google Scholar 

  28. Lorentzon J, Järvstråt N, Josefson BL (2009) Modelling chip formation of alloy 718. J Mater Process Technol 209(10):4645–4653. https://doi.org/10.1016/j.jmatprotec.2008.11.029

    Article  Google Scholar 

  29. Jafarian F, Ciaran MI, Umbrello D, Arrazola PJ, Filice L, Amirabadi H (2014) Finite element simulation of machining Inconel 718 alloy including microstructure changes. Int J Mech Sci 88:110–121. https://doi.org/10.1016/j.ijmecsci.2014.08.007

    Article  Google Scholar 

Download references

Funding

This work is supported by the National Natural Science Foundation of China (No.51775444) and the Fundamental Research Funds for the Central Universities (No.31020190502005).

Author information

Authors and Affiliations

  1. School of Mechanical Engineering, Northwestern Polytechnical University, Xi’an, 710072, Shaanxi, China

    Jinhua Zhou & Junxue Ren

Authors
  1. Jinhua Zhou
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Junxue Ren
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Jinhua Zhou.

Ethics declarations

Conflict of interest

The authors declare that they have no conflict of interest.

Additional information

Publisher’s note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Zhou, J., Ren, J. Predicting cutting force with unequal division parallel-sided shear zone model for orthogonal cutting. Int J Adv Manuf Technol 107, 4201–4211 (2020). https://doi.org/10.1007/s00170-020-05273-2

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-020-05273-2

Keywords

Search

Navigation