Skip to main content

Advertisement

SpringerLink
Log in

Machinability of green titanium powder compacts during drilling using HSS twist drills

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

The poor machinability of titanium-based alloys has until now been addressed by either choosing a suitable tool material, management of the heat generated during machining or by thermally assisted machining. This article reports on a new technique, called green machining, defined as the machining of compacted powders. Commercially pure titanium powder compacts possessing different strengths, called green strengths, were generated by uniaxial compaction and their drilling machinability characterized using the size of breakouts, surface finish of the drilled holes, and cutting forces. The cutting force for drilling sintered compacts was also determined for comparison purposes. The study found that all the green powder compacts could be drilled at high speeds regardless of their green strength. While high green strength, high speeds, and feed rates all affected machinability, feed rate was the main controlling factor. Also, depending on the binder used, cutting speed and feed rate could interact and worsen the machinability. However, compared to sintered compacts, the twist drills used on the green powder compacts did not catastrophically fail, and cutting forces were an order of magnitude less. It was concluded that green machining of titanium is a viable strategy to improve the poor machinability of the alloys.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9

Similar content being viewed by others

References

  1. Boyer RR (1996) An overview on the use of titanium in the aerospace industry. Mater Sci Eng A 213(1):103–114

    Google Scholar 

  2. Elias C, Lima J, Valiev R, Meyers M (2008) Biomedical applications of titanium and its alloys. JOM 60(3):46–49

    Google Scholar 

  3. Hayes J, Richards R (2010) The use of titanium and stainless steel in fracture fixation. Expert Rev Med Devices 7(6):843–853

    Google Scholar 

  4. Huang C, Jan L, Li R, Shih AJ (2007) A three-dimensional inverse problem in estimating the applied heat flux of a titanium drilling – theoretical and experimental studies. Int J Heat Mass Transf 50(17):3265–3277

    MATH  Google Scholar 

  5. Shokrani A, Dhokia V, Newman ST (2012) Environmentally conscious machining of difficult-to-machine materials with regard to cutting fluids. Int J Mach Tools Manuf 57:83–101

    Google Scholar 

  6. Li R, Shih AJ (2007) Tool temperature in titanium drilling. J Manuf Sci Eng 129(4):740–749

    Google Scholar 

  7. Kikuchi M (2009) The use of cutting temperature to evaluate the machinability of titanium alloys. Acta Biomater 5(2):770–775

    Google Scholar 

  8. Khanna N, Davim JP (2015) Design-of-experiments application in machining titanium alloys for aerospace structural components. Measurement 61:280–290

    Google Scholar 

  9. Sato M, Aoki T, Tanaka H, Takeda S (2013) Variation of temperature at the bottom surface of a hole during drilling and its effect on tool wear. Int J Mach Tools Manuf 68:40–47

    Google Scholar 

  10. Ezugwu E, Wang Z (1997) Titanium alloys and their machinability—a review. J Mater Process Technol 68(3):262–274

    Google Scholar 

  11. Li R, Hegde P, Shih AJ (2007) High-throughput drilling of titanium alloys. Int J Mach Tools Manuf 47(1):63–74

    Google Scholar 

  12. Sharif S, Rahim E (2007) Performance of coated-and uncoated-carbide tools when drilling titanium alloy—Ti–6Al4V. J Mater Process Technol 185(1–3):72–76

    Google Scholar 

  13. Robert-Perron E, Blais C, Pelletier S, Thomas Y (2007) Drilling of high quality features in green powder metallurgy components. Mater Sci Eng A 458(1):195–201

    Google Scholar 

  14. Aggarwal A, Singh H, Kumar P, Singh M (2008) Optimization of multiple quality characteristics for CNC turning under cryogenic cutting environment using desirability function. J Mater Process Technol 205(1):42–50

    Google Scholar 

  15. Yi S, Li G, Ding S, Mo J (2017) Performance and mechanisms of graphene oxide suspended cutting fluid in the drilling of titanium alloy ti-6Al-4V. J Manuf Process 29:182–193

    Google Scholar 

  16. Li G, Yi S, Li N, Pan W, Wen C, Ding S (2019) Quantitative analysis of cooling and lubricating effects of graphene oxide nanofluids in machining titanium alloy Ti6Al4V. J Mater Process Technol

  17. Pervaiz S, Deiab I, Darras B (2013) Power consumption and tool wear assessment when machining titanium alloys. Int J Precis Eng Manuf 14(6):925–936

    Google Scholar 

  18. El Baradie M (1996) Cutting fluids: part II. Recycling and clean machining. J Mater Process Technol 56(1–4):798–806

    Google Scholar 

  19. Zeilmann RP, Weingaertner WL (2006) Analysis of temperature during drilling of Ti6Al4V with minimal quantity of lubricant. J Mater Process Technol 179(1):124–127

    Google Scholar 

  20. Le Coz G, Marinescu M, Devillez A, Dudzinski D, Velnom L (2012) Measuring temperature of rotating cutting tools: Application to MQL drilling and dry milling of aerospace alloys. Appl Therm Eng 36:434–441

    Google Scholar 

  21. Ahmed LS, Govindaraju N, Pradeep KM (2016) Experimental investigations on cryogenic cooling in the drilling of titanium alloy. Mater Manuf Process 31(5):603–607

    Google Scholar 

  22. Bermingham M, Palanisamy S, Dargusch M (2012) Understanding the tool wear mechanism during thermally assisted machining ti-6Al-4V. Int J Mach Tools Manuf 62:76–87

    Google Scholar 

  23. Kahles J, Field M, Eylon D, Froes F (1985) Machining of titanium alloys. JOM 37(4):27–35

    Google Scholar 

  24. Saini Devi P, Woodall P (2003) Drill life optimisation when drilling TI-6AL-4V with HSS drills. ICME 9th international conference on manufacturing excellence

  25. Chatterjee S, Mahapatra SS, Abhishek K (2016) Simulation and optimization of machining parameters in drilling of titanium alloys. Simul Model Pract Theory 62:31–48

    Google Scholar 

  26. Froes FS, Gungor MN, Imam MA (2007) Cost-affordable titanium: the component fabrication perspective. JOM 59(6):28–31

    Google Scholar 

  27. Desbiens J, Robert-Perron E, Blais C, Chagnon F (2012) Effect of green machining on the tensile properties and fatigue strength of powder metallurgy sinter-hardenable steel components. Mater Sci Eng A 546(0):218–222

    Google Scholar 

  28. Inoue T, Shimazoe I, Sato I (2003) Practical application of drilling of compacts. J Jpn Soc Powder Powder Metall 50(11):927–930

    Google Scholar 

  29. Igarashi N, Sonoda Y, Take R, Terai H (2017) High-quality high-productivity manufacturing of variable valve timing parts by green machining. SEI Techn Rev 10:48–53

    Google Scholar 

  30. Laptev A, Bram M, Buchkremer HP, Stover D (2004) Study of production route for titanium parts combining very high porosity and complex shape. Powder Metall 47(1):85–92

    Google Scholar 

  31. Laptev A, Vyal O, Bram M, Buchkremer H, Stöver D (2005) Green strength of powder compacts provided for production of highly porous titanium parts. Powder Metall 48(4):358–364

    Google Scholar 

  32. Chagnon F, Tremblay L, St-Laurent S, Gagné M (1999) Improving green strength to enable green machining. SAE Trans:271–276

  33. Robertson IM, Schaffer GB (2010) Comparison of sintering of titanium and titanium hydride powders. Powder Metall 53(1):12–19

    Google Scholar 

  34. Machio C, Machaka R, Chikwanda HK (2016) Consolidation of titanium hydride powders during the production of titanium PM parts: the effect of die wall lubricants. Mater Des 90:757–766

    Google Scholar 

  35. Kikuchi M, Okuno O (2004) Machinability evaluation of titanium alloys (part 2). Dent Mater J 23(4):621–627

    Google Scholar 

  36. Luo SD, Yang YF, Schaffer GB, Qian M (2014) Warm die compaction and sintering of titanium and titanium alloy powders. J Mater Process Technol 214(3):660–666

    Google Scholar 

  37. Degnan C, Kennedy A, Shipway P (2007) Relationship between physical structure and machinability of green compacts. Powder Metall 50(1):14–20

    Google Scholar 

  38. Thomas Y, Cole KC, Tremblay L (2001) Complexable polymeric binder-lubricant blends. Advances in Powder Metallurgy and Particulate Materials, New Orleans, pp 3–20 Available at http://www.qmp.openface.ca

    Google Scholar 

  39. Zhang X, Takegoshi K, Hikichi K (1991) Miscibility of poly (vinyl alcohol)/poly (methacrylic acid) and poly (vinyl alcohol)/poly (acrylic acid) systems: I. high-resolution NMR studies in solution. Polym J 23(2):79

    Google Scholar 

  40. Liu T, Danaher J, Tremblay L, Guo R (2003) Green machining for conventional P/M processes. J Jpn Soc Powder Powder Metall 50(11):832–836

    Google Scholar 

  41. Tremblay L, Chagnon F, Thomas Y, Gagné M. Green machining of P/M parts using enhanced green strength lubricating systems. SAE 2001 Technical Paper 2001-01-0399, 2001 World Congress, https://doi.org/10.4271/2001-01-0399

  42. Park K, Beal A, Kim D, Kwon P, Lantrip J (2011) Tool wear in drilling of composite/titanium stacks using carbide and polycrystalline diamond tools. Wear 271(11):2826–2835

    Google Scholar 

  43. Rahim E, Sasahara H (2011) A study of the effect of palm oil as MQL lubricant on high speed drilling of titanium alloys. Tribol Int 44(3):309–317

    Google Scholar 

  44. Dornfeld D, Kim J, Dechow H, Hewson J, Chen L (1999) Drilling burr formation in titanium alloy, Ti-6Al-4V. CIRP Ann Manuf Technol 48(1):73–76

    Google Scholar 

  45. Dornfeld DA (2014) Moving towards green and sustainable manufacturing. Int J Precis Eng Manuf Green Technol 1(1):63–66

    Google Scholar 

Download references

Acknowledgments

Some drilling tests in this study were done at the Laboratory for Advanced Manufacturing, Stellenbosch University, Cape Town, South Africa.

Funding

This work was supported by the Department of Science and Technology (DST), South Africa, through the Titanium Centre of Competence (TiCoC), based at the Council for Scientific and Industrial Research (CSIR), Pretoria [DST/CON 0238; 2015].

Author information

Authors and Affiliations

  1. Material Science and Manufacturing, Light Metals, Council for Scientific and Industrial Research, P O Box 395, Pretoria, 0001, South Africa

    Mulalo T. Tambani & Christopher Machio

  2. School of Mechanical Engineering Sciences, University of Johannesburg, PO Box 524, Auckland Park, 2006, South Africa

    Mulalo T. Tambani & Daniel M. Madyira

Authors
  1. Mulalo T. Tambani
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Christopher Machio
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Daniel M. Madyira
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Christopher Machio.

Ethics declarations

Conflict of interest

The authors declare that they have no conflict of interest.

Additional information

Publisher’s note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Tambani, M.T., Machio, C. & Madyira, D.M. Machinability of green titanium powder compacts during drilling using HSS twist drills. Int J Adv Manuf Technol 106, 1723–1735 (2020). https://doi.org/10.1007/s00170-019-04712-z

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-019-04712-z

Keywords

Search

Navigation