Advertisement

EDM multi-pulse temperature field simulation of SiC/Al functionally graded materials

  • L. Tang
  • L. Ren
  • Q. L. Zhu
ORIGINAL ARTICLE
  • 63 Downloads

Abstract

In order to explore characteristics of electrical discharge machining (EDM) SiC/Al functionally graded materials, the simulation model of EDM continuous multi-pulse discharge temperature field was established. The dynamic simulation of continuous multi-pulse discharge was carried out. The pit position of the random distribution was analyzed using life and death method. The influence of peak current and pulse width on discharge pits and material removal rate was studied and verified experimentally. The results show that with the increasing of peak current and pulse width, the material removal rate is gradually increased. The simulation results are the same direction as the experimental results, and the error analysis is carried out. The maximum error of theoretical experimental results is 9.84% and the minimum error is 5.10%.

Keywords

Functionally graded materials (FGM) Electrical discharge machining (EDM) Continuous multi-pulse discharge Method of life and death 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Acknowledgements

The authors would like to thank Mr. Zhao for his fruitful discussion.

Funding information

This work was financially supported by the National Natural Science Foundation of China (Grant No. 51405365), Shaanxi Provincial Education Department service local special plan project (Grant No. 17JF010), Jiangsu Key Laboratory of Precision and Micro-Manufacturing Technology, Key Laboratory of Science and Technology Innovation Project of Shaanxi Province (Grant No. 2014SZS20-Z01, No. 2014SZS20-P05), the Open Research Fund Program of Shaanxi Key Laboratory of Non-Traditional Machining (Grant No. 2015SZSj-61-6), and Science and Technology Planning Project of Shaanxi Province (Grant No. 2014JM7253).

References

  1. 1.
    Kumar S, Reddy KVVSM, Kumar A, Devi GR (2013) Development and characterization of polymer-ceramic continuous fiber reinforced functionally graded composites for aerospace application. Dialogues Cardiovasc Med DCM 26(1):185–191Google Scholar
  2. 2.
    Hideki S, Katsumi K, Hitoshi O (2010) Application feasibility of permittivity graded FGM (functionally graded materials) for gas-insulated equipment. Electr Eng Jpn 162(2):39–45Google Scholar
  3. 3.
    Chmielewski M, Pietrzak K (2016) Metal-ceramic functionally graded materials-manufacturing, characterization, application. Bull Polish Acad Sci Tech Sci 64(1):151–160Google Scholar
  4. 4.
    El-Wazery MS, El-Desouky AR (2015) A review on functionally graded ceramic-metal materials. J Mater Environ Sci 6(5):1369–1376Google Scholar
  5. 5.
    Naebe M, Shirvanimoghaddam K (2016) Functionally graded materials: a review of fabrication and properties. Appl Mater Today 5:223–245CrossRefGoogle Scholar
  6. 6.
    Sobczak JJ, Drenchev L (2013) Metallic functionally graded materials: a specific class of advanced composites. J Mater Sci Technol 29(4):297–316CrossRefGoogle Scholar
  7. 7.
    Zhou MY, Xi JT, Yan JQ (2004) Modeling and processing of functionally graded materials for rapid prototyping. J Mater Process Technol 146(3):396–402CrossRefGoogle Scholar
  8. 8.
    Wang Z, Cheng J, Geng X, Wang (2013) Development of metal-ceramic functionally graded materials and its EDM processing prospects. Electromachining & Mould (In Chinese)Google Scholar
  9. 9.
    Liu H, Wang Z, Wang Y, Li H (2016) Self-induced electrical discharge machining of Ni-Al2O3, functionally graded materials. Int J Adv Manuf Technol 83(1–4):587–594CrossRefGoogle Scholar
  10. 10.
    Muthuramalingam T, Mohan B (2015) A review on influence of electrical process parameters in EDM process. Arch Civil Mech Eng 15(1):87–94CrossRefGoogle Scholar
  11. 11.
    Seo YW, Kim D, Ramulu M (2006) Electrical discharge machining of functionally graded 15â35 Vol% SiCp/Al composites. Adv Manuf Process 21(5):479–487CrossRefGoogle Scholar
  12. 12.
    Hourmand M, Farahany S, Sarhan AAD, Noordin MY (2015) Investigating the electrical discharge machining (EDM) parameter effects on Al-Mg2Si metal matrix composite (MMC) for high material removal rate (MRR) and less EWR–RSM approach. Int J Adv Manuf Technol 77(5–8):831–838CrossRefGoogle Scholar
  13. 13.
    Pandey AB, Brahmankar PK (2016) A method to predict possibility of arcing in EDM of TiB 2 p reinforced ferrous matrix composite. Int J Adv Manuf Technol 86(9):1–13Google Scholar
  14. 14.
    Mohan B, Rajadurai A, Satyanarayana KG (2002) Effect of SiC and rotation of electrode on electric discharge machining of Al–SiC composite. J Mater Process Technol 124(3):297–304CrossRefGoogle Scholar
  15. 15.
    Mohan B, Rajadurai A, Satyanarayana KG (2004) Electric discharge machining of Al–SiC metal matrix composites using rotary tube electrode. J Mater Process Technol 153–154(1):978–985CrossRefGoogle Scholar
  16. 16.
    Pramanik A (2014) Developments in the non-traditional machining of particle reinforced metal matrix composites. Int J Mach Tools Manuf 86(11):44–61CrossRefGoogle Scholar
  17. 17.
    Liu JW, Yue TM, Guo ZN (2010) An analysis of the discharge mechanism in electrochemical discharge machining of particulate reinforced metal matrix composites. Int J Mach Tools Manuf 50(1):86–96CrossRefGoogle Scholar
  18. 18.
    Kurniawan R, Kumaran ST, Prabu VA, Yu Z, Park KM, Ye IK (2017) Measurement of burr removal rate and analysis of machining parameters in ultrasonic assisted dry EDM (US-EDM) for deburring drilled holes in CFRP composite. Measurement 110:98–115CrossRefGoogle Scholar
  19. 19.
    Teimouri R, Baseri H (2013) Experimental study of rotary magnetic field-assisted dry EDM with ultrasonic vibration of workpiece. Int J Adv Manuf Technol 67(5–8):1371–1384CrossRefGoogle Scholar
  20. 20.
    Abdullah A, Shabgard MR (2008) Effect of ultrasonic vibration of tool on electrical discharge machining of cemented-tungsten carbide (WC-Co). Int J Adv Manuf Technol 38:1137–1147CrossRefGoogle Scholar
  21. 21.
    Singh S, Maheshwari S, Pandey PC (2008) Effect of SiC powder-suspended dielectric fluid on the surface finish of 6061Al/Al2O3P/20p composites during electric discharge machining. Int J Mach Mach Mater 4(2/3):252Google Scholar
  22. 22.
    Kansal HK (2006) An experimental study of the machining parameters in powder mixed electric discharge machining of Al–10%SiC P, metal matrix composites. Int J Mach Mach Mater 1(4):396–411Google Scholar
  23. 23.
    Marafona J, Chousal JAG (2006) A finite element model of EDM based on the Joule effect. Int J Mach Tools Manuf 46(6):595–602CrossRefGoogle Scholar
  24. 24.
    Shabgard M, Ahmadi R, Seyedzavvar M, Oliaei SNB (2013) Mathematical and numerical modeling of the effect of input-parameters on the flushing efficiency of plasma channel in EDM process. Int J Mach Tools Manuf 65(23):79–87CrossRefGoogle Scholar
  25. 25.
    Weingärtner E, Kuster F, Wegener K (2012) Modeling and simulation of electrical discharge machining. Procedia Cirp 2(7):74–78CrossRefGoogle Scholar
  26. 26.
    Fan C (2013) Analysis of fracture behavior of metal/ceramic functionally graded materials under thermal stress. Adv Mater Res 750-752:2200–2205CrossRefGoogle Scholar
  27. 27.
    Burlayenko VN, Altenbach H, Sadowski T, Dimitrova SD, Bhaskar A (2017) Modelling functionally graded materials in heat transfer and thermal stress analysis by means of graded finite elements. Appl Math Model 45:422–438MathSciNetCrossRefGoogle Scholar
  28. 28.
    Xie BC, Wang YK, Wang ZL, Zhao WS (2011) Numerical simulation of titanium alloy machining in electric discharge machining process. Trans Nonferrous Metals Soc China 21(21):s434–s439 (In Chinese)CrossRefGoogle Scholar
  29. 29.
    Hayakawa S, Kojima H, Kunieda M, Nishiwaki N (1996) Influence of plasma extinction on machining stability in EDM process. J Jpn Soc Precis Eng 62(5):686–690CrossRefGoogle Scholar
  30. 30.
    Xia H, Hashimoto H, Kunieda M, Nishiwaki N (1996) Measurement of energy distribution in continuous EDM process. J Jpn Society Precis Eng 62(8):1141–1145CrossRefGoogle Scholar
  31. 31.
    Eubank PT, Patel MR, Barrufet MA, Bozkurt B (1993) Theoretical models of the electrical discharge machining process. III. The variable mass, cylindrical plasma model. J Appl Phys 73(11):7900–7909CrossRefGoogle Scholar
  32. 32.
    Ikai T, Hashigushi K (1995) Heat input for crater formation in EDM, proceedings of international symposium for electro machining-ISEMXI. EPFL, Lausanne, Switzerland 12(1):163–170Google Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2018

Authors and Affiliations

  1. 1.School of Mechatronics EngineeringXi’an Technological UniversityXi’anPeople’s Republic of China

Personalised recommendations