Development of multipass skew rolling technology for stainless steel and alloy pipes’ production

Abstract

The paper presents the development of new technology and equipment for seamless pipe rolling from hard deformable stainless steels and nickel-base alloys. The research in piercing and elongation of pipes was carried out in the laboratory of the National University of Science and Technology “MISIS” (NUST “MISIS”) and in factory conditions. The study confirmed the possibility of obtaining pipes with high accuracy. Given the research results, a new technology and special equipment for 90–270-mm diameter hot-rolled seamless pipes manufactured from high-alloy steels and alloys was proposed. The technology is based on the processes of two-stage hot piercing in a two roll skew rolling mill with guide shoes and conical mandrel. Elongation in a two roll mill on a long cylindrical mandrel makes it possible to obtain pipes of alloyed steels with ratio of outer diameter to wall thickness up to 27. High quality of pipes with wall variation up to 6% is achieved through the distribution of the coefficient of elongation and the reduction in the operations.

This is a preview of subscription content, log in to check access.

References

  1. 1.

    Wanga L, Liu F, Zuo Q, Chen CF (2013) Prediction of flow stress for N08028 alloy under hot working conditions. Mater Des 47:737–745

    Article  Google Scholar 

  2. 2.

    Zuo Q, Liu F, Wang L, Chen C, Zhang Z (2015) Prediction of hot deformation behavior in Ni-based alloy considering the effect of initial microstructure. Prog Nat Sci Mater Int 25:66–77

    Article  Google Scholar 

  3. 3.

    Wang L, Liu F, Cheng JJ, Zuo Q, Chen CF (2015) Hot deformation characteristics and processing map analysis for Nickel-based corrosion resistant alloy. J Alloys Compd 623:69–78

    Article  Google Scholar 

  4. 4.

    Zhang HY, Zhang SH, Cheng M, Li ZX (2010) Deformation characteristics of δ phase in the delta-processed Inconel 718 alloy. Mater Charact 61:49–53

    Article  Google Scholar 

  5. 5.

    Thomas A, El-Wahabi M, Cabrera JM, Prado JM (2006) High temperature deformation of Inconel 718. J Mater Process Technol 177:469–472

    Article  Google Scholar 

  6. 6.

    Momeni A, Dehghani K, Keshmiri H, Ebrahimi GR (2010) Hot deformation behavior and microstructural evolution of a superaustenitic stainless steel. Mater Sci Eng 527:1605–1611

    Article  Google Scholar 

  7. 7.

    Epler ME, Misiolek WZ (2006) Novel billet design for co-extrusion of ferrous material tubes. Mater Sci Eng A 429:43–49

    Article  Google Scholar 

  8. 8.

    Hansson S, Fisk M (2010) Simulations and measurements of combined induction heating and extrusion processes. Finite Elem Anal Des 46:905–915

    Article  Google Scholar 

  9. 9.

    Qamar SZ, Sheikh AK, Arif AFM, Younas M, Pervez T (2008) Monte Carlo simulation of extrusion die life. J Mater Process Technol 202:96–106

    Article  Google Scholar 

  10. 10.

    Hansson S, Jansson T (2010) Sensitivity analysis of a finite element model for the simulation of stainless steel tube extrusion. J Mater Process Technol 210:1386–1396

    Article  Google Scholar 

  11. 11.

    Romantsev BA, Aleshchenko AS, Goncharuk AV, Galkin SP (2012) Mini tube-production unit 40–80 with a three-high reeling mill. Metallurgist 55:918–924 (in russian)

    Article  Google Scholar 

  12. 12.

    Romantsev BA, Goncharuk AV, Aleshchenko AS, Gamin YV (2015) Production of hollow thick-walled profiles and pipes made of titanium alloys by screw rolling. Russ J Non-Ferrous Met 56:522–526 (in russian)

    Article  Google Scholar 

  13. 13.

    Romantsev BA, Zimin VY, Goncharuk AV, Mintahanov MA, Pakhomov VP (2009) Development of seamless pipe production in JSC “ Vyksunskii metallurgicheskii zavod”. Prod Rolled 6:32–34 (in russian)

    Google Scholar 

  14. 14.

    Romantsev BA, Goncharuk AV, Zimin VY, Pakhomov VP, Aleshchenko AS, Matyko OK (2009) Introducing seamless-pipe production at JSC Vyksunskii metallurgicheskii zavod. Steel Translat 39:803–805 (in russian)

    Article  Google Scholar 

  15. 15.

    Romantsev BA, Goncharuk AV, Aleshchenko AS, Onuchin AB, Gamin YV (2015) Improving the Regimes Used for Hot-Rolling Tubes on Mini Tube-Production Unit 70–270. Metallurgist 5:41–43 (in russian)

    Google Scholar 

Download references

Acknowledgments

We thank the engineering staff from JSC “Vyksa Steel Works” and JSC “Volzhsky Pipe Plant” who provided industrial expertise that greatly assisted the research of piercing and elongation processes that were carried out on TRP 70–270 and TRP 50–200.

Author information

Affiliations

Authors

Corresponding author

Correspondence to Yury Gamin.

Rights and permissions

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Romantsev, B., Goncharuk, A., Aleshchenko, A. et al. Development of multipass skew rolling technology for stainless steel and alloy pipes’ production. Int J Adv Manuf Technol 97, 3223–3230 (2018). https://doi.org/10.1007/s00170-018-2134-3

Download citation

Keywords

  • Piercing process
  • Skew rolling
  • Rotary piercing mill
  • Stainless steel
  • Heat-resistant alloy
  • Super alloy