Advertisement

Study on burr occurrence and surface integrity during slot milling of multidirectional and plain woven CFRPs

  • Maojun Li
  • Mingjie Huang
  • Xiaogeng Jiang
  • Chun-liang Kuo
  • Xujing Yang
ORIGINAL ARTICLE

Abstract

Machining carbon fiber reinforced composite (CFRP) is often accompanied with cutting edge defects and surface damage including interlayer delamination, cavities and debonding of fiber-matrix. A detailed understanding of the effect of fiber configuration and cutting parameters on cutting force, burr occurrence/formation and surface integrity is necessary. In this paper, experimental data is presented relating to fiber burrs on entry surface, cutting force, surface roughness and workpiece integrity when slot milling CFRP laminates with varying fiber configurations (0°/90°, 45°/135° and plain woven) at different cutting speed (60 and 120 m/min) and feed rate (0.05 and 0.1 mm/rev). Lateral cutting force is recorded down to 56 N and highly dependent on fiber orientation. The length (up to ~ 5.6 mm) and amount of fiber burrs are highly related to fiber orientation and fiber cutting angle. Surface roughness Ra down to ~ 1.4 μm was recorded when milling type 2 (45°/135°) and type 3 (plain woven) laminates. Various surface defects predominantly occurred due to different cutting conditions and fiber configurations, which are mainly located in the layers with fibers orientated at 45°/135°. The occurrence and propagation of fiber burrs and surface cavities were also investigated based on different fiber fracture mechanisms.

Keywords

Carbon fibers Slot milling Burr formation Surface integrity 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Acknowledgements

The authors would like to appreciate the financial support sponsored by the Research Project Program of the Education Committee of Tianjin (2017KJ079), the Fundamental Research Funds for the Central Universities (531107050870) and Tianjin Natural Science Foundation (16JCYBJC41300).

References

  1. 1.
    Teti R (2002) Machining of composite materials. CIRP Ann Manuf Technol 51(2):611–634CrossRefGoogle Scholar
  2. 2.
    Soutis C (2005) Fibre reinforced composites in aircraft construction. Prog Aerosp Sci 41(2):143–151CrossRefGoogle Scholar
  3. 3.
    Jacob A (2014) Carbon fibre and cars—2013 in review. Reinf Plast 58(1):18–19CrossRefGoogle Scholar
  4. 4.
    Park SJ, Kim BJ (2015) Carbon fibers and their composites. Springer, NetherlandsCrossRefGoogle Scholar
  5. 5.
    Karpat Y, Bahtiyar O, Değer B (2012) Milling force modelling of multidirectional carbon fiber reinforced polymer laminates. Procedia CIRP 1:460–465CrossRefGoogle Scholar
  6. 6.
    Wang H, Qin X, Li H (2015) Machinability analysis on helical milling of carbon fiber reinforced polymer. J Adv Mech Des Syst Manuf.  https://doi.org/10.1299/jamdsm.2015jamdsm0057
  7. 7.
    Wang C, Liu G, An Q, Chen M (2017) Occurrence and formation mechanism of surface cavity defects during orthogonal milling of CFRP laminates. Compos Part B Eng 109:10–22CrossRefGoogle Scholar
  8. 8.
    Wang FJ, Yin JW, Ma JW, Jia ZY, Yang F, Niu B (2017) Effects of cutting edge radius and fiber cutting angle on the cutting-induced surface damage in machining of unidirectional CFRP composite laminates. Int J Adv Manuf Technol 91(9–12):3107–3120CrossRefGoogle Scholar
  9. 9.
    Hintze W, Cordes M, Koerkel G (2015) Influence of weave structure on delamination when milling CFRP. J Mater Process Technol 216:199–205CrossRefGoogle Scholar
  10. 10.
    Wang XM, Zhang LC (2003) An experimental investigation into the orthogonal cutting of unidirectional fibre reinforced plastics. Int J Mach Tools Manuf 43(10):1015–1022CrossRefGoogle Scholar
  11. 11.
    Hintze W, Hartmann D, Schütte C (2011) Occurrence and propagation of delamination during the machining of carbon fibre reinforced plastics (CFRPs)—an experimental study. Compos Sci Technol 71(15):1719–1726CrossRefGoogle Scholar
  12. 12.
    Davim JP, Reis P, António CC (2004) A study on milling of glass fiber reinforced plastics manufactured by hand-lay up using statistical analysis (ANOVA). Compos Struct 64(3–4):493–500CrossRefGoogle Scholar
  13. 13.
    Rajesh Mathivanan N, Mahesh BS, Anup Shetty H (2016) An experimental investigation on the process parameters influencing machining forces during milling of carbon and glass fiber laminates. Measurement 91:39–45CrossRefGoogle Scholar
  14. 14.
    Wang H, Sun J, Li J, Lu L, Li N (2015) Evaluation of cutting force and cutting temperature in milling carbon fiber-reinforced polymer composites. Int J Adv Manuf Technol 82(9–12):1517–1525Google Scholar
  15. 15.
    Gara S, Tsoumarev O (2015) Effect of tool geometry on surface roughness in slotting of CFRP. Int J Adv Manuf Technol 86(1–4):451–461Google Scholar
  16. 16.
    Sheikh-Ahmad J, Urban N, Cheraghi H (2012) Machining damage in edge trimming of CFRP. Mater Manuf Process 27(7):802–808CrossRefGoogle Scholar
  17. 17.
    Davim JP, Reis P (2005) Damage and dimensional precision on milling carbon fiber-reinforced plastics using design experiments. J Mater Process Technol 160(2):160–167CrossRefGoogle Scholar
  18. 18.
    Haddad M, Zitoune R, Eyma F, Castanie B (2014) Study of the surface defects and dust generated during trimming of CFRP: influence of tool geometry, machining parameters and cutting speed range. Compos A Appl Sci 66:142–154CrossRefGoogle Scholar
  19. 19.
    Erkan Ö, Işık B, Çiçek A, Kara F (2012) Prediction of damage factor in end milling of glass fibre reinforced plastic composites using artificial neural network. Appl Compos Mater 20(4):517–536CrossRefGoogle Scholar
  20. 20.
    Voss R, Seeholzer L, Kuster F, Wegener K (2017) Influence of fibre orientation, tool geometry and process parameters on surface quality in milling of CFRP. CIRP J Manuf Sci Technol 18:75–91CrossRefGoogle Scholar
  21. 21.
    Wang H, Sun J, Zhang D, Guo K, Li J (2016) The effect of cutting temperature in milling of carbon fiber reinforced polymer composites. Compos A Appl Sci 91:380–387CrossRefGoogle Scholar
  22. 22.
    Karpat Y, Bahtiyar O, Değer B (2012) Mechanistic force modeling for milling of unidirectional carbon fiber reinforced polymer laminates. Int J Mach Tools Manuf 56:79–93CrossRefGoogle Scholar
  23. 23.
    Henerichs M, Voß R, Kuster F, Wegener K (2015) Machining of carbon fiber reinforced plastics: influence of tool geometry and fiber orientation on the machining forces. CIRP J Manuf Sci Technol 9:136–145CrossRefGoogle Scholar
  24. 24.
    Li H, Qin X, He G, Price MA, Jin Y, Sun D (2017) An energy based force prediction method for UD-CFRP orthogonal machining. Compos Struct 159:34–43CrossRefGoogle Scholar
  25. 25.
    Hintze W, Hartmann D (2013) Modeling of delamination during milling of unidirectional CFRP. Procedia CIRP 8:444–449CrossRefGoogle Scholar
  26. 26.
    Gara S, Tsoumarev O (2016) Prediction of surface roughness in slotting of CFRP. Measurement 91:414–420CrossRefGoogle Scholar
  27. 27.
    Azmi AI, Lin RJT, Bhattacharyya D (2012) Machinability study of glass fibre-reinforced polymer composites during end milling. Int J Adv Manuf Technol 64(1–4):247–261Google Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2018

Authors and Affiliations

  • Maojun Li
    • 1
  • Mingjie Huang
    • 1
  • Xiaogeng Jiang
    • 2
  • Chun-liang Kuo
    • 3
  • Xujing Yang
    • 1
  1. 1.State Key Laboratory of Advanced Design and Manufacture for Vehicle BodyHunan UniversityChangshaChina
  2. 2.School of Mechanical EngineeringTianjin Polytechnic UniversityTianjinChina
  3. 3.Department of Mechanical EngineeringNational Taiwan University of Science and TechnologyTaipeiTaiwan

Personalised recommendations