Monitoring of the condition of turning machine bearing housing through vibrations

  • Anton Panda
  • Štefánia Olejárová
  • Jan Valíček
  • Marta Harničárová
ORIGINAL ARTICLE
  • 14 Downloads

Abstract

Mechanical vibration is a phenomenon that occurs very often in the process of metal cutting. It is one of many factors that have a significant impact on the quality of machining and thus prevent a rise in productivity. These vibrations are undesirable not only because they cause noise and dynamic stresses, which result in fatigue and failure of the machine, but also energy loss or performance reduction. An experimental analysis of mechanical vibrations in the machining process is important because vibrations may cause spindle damage, machine tool wear or workpiece wear and may be left with poor surface finish. Therefore, this material is devoted to the study of the impact of input cutting parameters—spindle speed and depth of cut on the formation and size of mechanical vibrations on lathe bearing housings. The measured experimental values of the acceleration amplitude of mechanical vibrations on bearing housings were compared with theoretical values.

Keywords

Lathe processing Mechanical vibration Vibration acceleration amplitude Frequency Frequency spectrum 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Neslušan M, Čiliková M (2007) Theory of machining. EDIS ŽilinaGoogle Scholar
  2. 2.
    Janáč A., Lipa Z., Peterka J (2006) Theory of machining. Slovak University of Technology in BratislavaGoogle Scholar
  3. 3.
    Tlusty J, Spacek L (1954) Self-excited vibialions in machine tools. CSAV, PragueGoogle Scholar
  4. 4.
    Fojtů P (2009) The issue of self-excited oscillations. CVUT, PragueGoogle Scholar
  5. 5.
    Huang HH, Wang HP (1996) An integrated monitoring and diagnostic system for roller bearings. Int J Adv Manuf Technol 12:37–46CrossRefGoogle Scholar
  6. 6.
    Li CJ, Wu SM (1989) On-line detection of localized defects in bearings by pattern recognition analysis. J Manuf Sci Eng 111:331–336Google Scholar
  7. 7.
    Kurfess TR, Billington S, Liang SY (2006) Advanced diagnostic and prognostic techniques for rolling element bearings. In: Wang L, Gao RX (eds) Condition monitoring and control for intelligent manufacturing. Springer series in advanced manufacturing. Springer, London, pp 137–165CrossRefGoogle Scholar
  8. 8.
    Wei J, Zhang G (2010) A precision grinding method for screw rotors using CBN grinding wheel. Int J Adv Manuf Technol 48:495–503CrossRefGoogle Scholar
  9. 9.
    Chen ZZ, Xu JH, Ding WF, Ma CY, Fu YC (2015) Grinding temperature during high-efficiency grinding Inconel 718 using porous CBN wheel with multilayer defined grain distribution. Int J Adv Manuf Technol 77:165–172CrossRefGoogle Scholar
  10. 10.
    Ding K, Fu Y, Su H, Gong X, Wu K (2014) Wear of diamond grinding wheel in ultrasonic vibration-assisted grinding of silicon carbide. Int J Adv Manuf Technol 71:1929–1938CrossRefGoogle Scholar
  11. 11.
    Wang JM, Ye RZ, Tang YP, Bin HZ, Li ZB (2010) Research on the technology for outer race elliptical groove grinding with basin-like grinding wheel. Int J Adv Manuf Technol 49:497–504CrossRefGoogle Scholar
  12. 12.
    Jurko J, Panda A, Valíček J, Harničárová M, Pandová I (2015) Study on cone roller bearing surface roughness improvement and the effect of surface roughness on tapered roller bearing service life. Int J Adv Manuf Technol 82:1099–1106CrossRefGoogle Scholar
  13. 13.
    Panda A, Jurko J, Džupon M, Pandová I (2011) Optimalization of heat treatment bearings rings with goal to eliminate deformation of material. Chem List 105:459–461Google Scholar
  14. 14.
    Tandon N, Nakra BC (1992) Vibration and acoustic monitoring techniques for the detection of defects in rolling element bearings-a review. Shock Vib 24:3–11CrossRefGoogle Scholar
  15. 15.
    Gohar R, Akturk N (1998) Vibrations associated with ball bearings. In: Proceedings of IMechE conference on multi-body dynamics: new techniques and applications, LondonGoogle Scholar
  16. 16.
    McFadden PD, Smith JD (1984) Model for the vibration produced by a single point defect in a rolling element bearing. J Sound Vib 96:69–82CrossRefGoogle Scholar
  17. 17.
    McFadden PD, Smith JD (1985) The vibration produced by multiple point defect in a rolling element bearing. J Sound Vib 98:263–273CrossRefGoogle Scholar
  18. 18.
    Tandon N, Choudhury A (1997) An analytical model for the prediction of the vibration response of rolling element bearings due to a localized defect. J Sound Vib 205:275–292CrossRefGoogle Scholar
  19. 19.
    Braun S, Datner B (1979) Analysis of roller/ball bearing vibrations. J Mech Des 101:118–125CrossRefGoogle Scholar
  20. 20.
    Prashad H, Ghosh M, Biswas S (1985) Diagnostic monitoring of rolling-element bearings by high-frequency resonance technique. ASLE Trans 28:439–448CrossRefGoogle Scholar
  21. 21.
    Ono K, Okada Y (1998) Analysis of ball bearing vibrations caused by outer race waviness. J Vib Acoust 120:901–908CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2018

Authors and Affiliations

  • Anton Panda
    • 1
  • Štefánia Olejárová
    • 2
  • Jan Valíček
    • 3
    • 4
  • Marta Harničárová
    • 3
    • 4
  1. 1.Department of Automobile and Manufacturing Technologies, Faculty of Manufacturing TechnologiesTechnical University of Košice with a seat in PrešovPrešovSlovakia
  2. 2.Department of Technical Systems Design and Monitoring, Faculty of Manufacturing TechnologiesTechnical University of Košice with a seat in PrešovPrešovSlovakia
  3. 3.RMTVC, Faculty of Metallurgy and Materials EngineeringVŠB—Technical University of OstravaOstrava-PorubaCzech Republic
  4. 4.Slovak University of Agriculture in Nitra, Technical FacultyNitraSlovakia

Personalised recommendations