Skip to main content
SpringerLink
Log in

Prediction and experimental validation of temperature rise in ductile mode end milling of soda-lime glass

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

The suitable thermal, chemical, and corrosion resistance properties of glass make it possible to be used in a wide variety of product manufacturing, like lenses, mirrors, mold, semiconductor, biomedical, optical, and micro-electronics. However, machining of glass like any brittle material has big challenges owing to its inherent brittleness. Ductile mode machining is known to promote the material removal from a brittle material in ductile manner rather than by brittle fracture. In high-speed machining, the thermal softening effects can enhance flexibility in ductile machining of brittle materials. In this paper, an analytical model is developed to predict the amount of temperature generated in the immediate next removable layer (INRL) of the soda-lime glass work piece per unit depth of cut \( \Delta {\overline{T}}_{\mathrm{INRL}} \) based on fundamental micro-machining principle and material physical properties. The model incorporates the effects of cutting speed, feed rate, strain rate, and thermal softening effect. The simulation and experimental results showed that at high cutting speed, glass softening can be achieved by adiabatic heating in order to facilitate ductile machining. The amount of adiabatic heating can be controlled by predicting the amount of the \( \Delta {\overline{T}}_{\mathrm{INRL}} \).

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Foy K et al (2009) Effect of tilt angle on cutting regime transition in glass micromilling. Int J Mach Tools Manuf 49(3):315–324

    Article  Google Scholar 

  2. Smith, W.F. and J. Hashemi, Foundations of materials science and engineering. 2006: Mcgraw-Hill Publishing

  3. Bifano, T.G., T.A. Dow, and R.O. Scattergood. Ductile-regime grinding of brittle materials: experimental results and the development of a model. In 32nd Annual Technical Symposium. 1989. International Society for Optics and Photonics

  4. Arefin S et al The upper bound of tool edge radius for nanoscale ductile mode cutting of silicon wafer. Int J Adv Manuf Technol 2007, 31(7–8):655–662

  5. Cai M, Li X, Rahman M (2007) Study of the mechanism of nanoscale ductile mode cutting of silicon using molecular dynamics simulation. Int J Mach Tools Manuf 47(1):75–80

    Article  Google Scholar 

  6. Arif M, Rahman M, San WY (2011) Analytical model to determine the critical feed per edge for ductile–brittle transition in milling process of brittle materials. Int J Mach Tools Manuf 51(3):170–181

    Article  Google Scholar 

  7. Zhao, Y., et al. An experimental investigation on the surface morphology in micro-end-milling of glass. In Automation and Computing (ICAC), 2014 20th International Conference on. 2014. IEEE

  8. Moriwaki T, Shamoto E, Inoue K (1992) Ultraprecision ductile cutting of glass by applying ultrasonic vibration. CIRP Annals-Manufacturing Technol 41(1):141–144

    Article  Google Scholar 

  9. Zhang X et al (2013) A model to predict the critical undeformed chip thickness in vibration-assisted machining of brittle materials. Int J Mach Tools Manuf 69:57–66

    Article  Google Scholar 

  10. Lin S et al (2015) Application of ultrasonic assisted machining technique for glass-ceramic milling. World Academy Sci, Engineering Technol, Int J Mechanical, Aerospace, Industrial, Mechatronic Manufacturing Engineering 9(5):802–807

    Google Scholar 

  11. Rao DMS, Shrekanth D (2014) Abrasive jet machining-research review. Int J Advanced Engineering Technol 5:18–24

    Google Scholar 

  12. Aich U et al (2014) Abrasive water jet cutting of borosilicate glass. Procedia Materials Sci 6:775–785

    Article  Google Scholar 

  13. Jui SK, Kamaraj AB, Sundaram MM (2013) High aspect ratio micromachining of glass by electrochemical discharge machining (ECDM). J Manuf Process 15(4):460–466

    Article  Google Scholar 

  14. Mohammadi H et al (2015) Experimental work on micro laser-assisted diamond turning of silicon (111). J Manuf Process 19:125–128

    Article  Google Scholar 

  15. Wlodarczyk KL et al (2016) Picosecond laser cutting and drilling of thin flex glass. Opt Lasers Eng 78:64–74

    Article  Google Scholar 

  16. Sajjadi, M., et al. Investigation of micro scratching and machining of glass. In ASME 2009 International Manufacturing Science and Engineering Conference. 2009. American Society of Mechanical Engineers

  17. Reddy, M.M., A. Gorin, and K. Abou-El-Hossein. Predictive surface roughness model for end milling of machinable glass ceramic. In IOP Conference Series: Materials Science and Engineering. 2011. IOP Publishing

  18. Amin A et al (2016) An experimental approach to determine the critical depth of cut in brittle-to-ductile phase transition during end milling of soda-lime glass. Arab J Sci Eng 41(11):4553–4562

    Article  Google Scholar 

  19. Le Bourhis E, Metayer D (2000) Indentation of glass as a function of temperature. J Non-Cryst Solids 272(1):34–38

    Article  Google Scholar 

  20. Michel M et al (2004) High temperature microhardness of soda-lime glass. J Non-Cryst Solids 348:131–138

    Article  Google Scholar 

  21. Rouxel T, Sanglebœuf J-C (2000) The brittle to ductile transition in a soda–lime–silica glass. J Non-Cryst Solids 271(3):224–235

    Article  Google Scholar 

  22. Johnson, G.R. and W.H. Cook. A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures. In Proceedings of the 7th International Symposium on Ballistics. 1983. The Hague, The Netherlands

  23. Rao S, Shunmugam M (2012) Analytical modeling of micro end-milling forces with edge radius and material strengthening effects. Mach Sci Technol 16(2):205–227

    Article  Google Scholar 

  24. Srinivasa Y, Shunmugam M (2013) Mechanistic model for prediction of cutting forces in micro end-milling and experimental comparison. Int J Mach Tools Manuf 67:18–27

    Article  Google Scholar 

  25. Venkatachalam S et al (2015) Microstructure effects on cutting forces and flow stress in ultra-precision machining of polycrystalline brittle materials. J Manuf Sci Eng 137(2):021020

    Article  MathSciNet  Google Scholar 

  26. Venkatachalam S, Li X, Liang SY (2009) Predictive modeling of transition undeformed chip thickness in ductile-regime micro-machining of single crystal brittle materials. J Mater Process Technol 209(7):3306–3319

    Article  Google Scholar 

  27. Oxley, P., The mechanics of metal cutting. An analytical approach to assessing machinability. 1989, Chichester, Elis Horwood Limited

  28. Altintas, Y., Mechanics of metal cutting. Manufacturing automation: metal cutting mechanics, machine tool vibrations, and CNC design, Cambridge, UK. Cambridge University Press, 2000: p. 4–65

  29. Zhou L et al (2015) Analytical modeling and experimental validation of micro end-milling cutting forces considering edge radius and material strengthening effects. Int J Mach Tools Manuf 97:29–41

    Article  Google Scholar 

  30. Boothroyd, G. and Ey, Temperatures in orthogonal metal cutting. Proceedings Institution Mechanical Engineers, 1963. 177(1): p. 789–810

  31. Lazoglu I, Altintas Y (2002) Prediction of tool and chip temperature in continuous and interrupted machining. Int J Mach Tools Manuf 42(9):1011–1022

    Article  Google Scholar 

  32. Callister, W.D. and D.G. Rethwisch, Materials science and engineering. Vol. 5. 2011: John Wiley & Sons NY

  33. Zhang X, Hao H, Ma G (2015) Dynamic material model of annealed soda-lime glass. Int J Impact Eng 77:1088–1119

    Article  Google Scholar 

  34. Callister, W.D. and D.G. Rethwisch, Materials science and engineering: an introduction. Vol. 7. 2007: Wiley New York

  35. Holmquist TJ, Johnson GR (2011) A computational constitutive model for glass subjected to large strains, high strain rates and high pressures. J Appl Mech 78(5):051003

    Article  Google Scholar 

  36. Zhang X, Hao H, Ma G (2015) Dynamic material model of annealed soda-lime glass. Int J Impact Engineering 77:108–119

    Article  Google Scholar 

  37. Nie X et al (2009) Effect of loading rate and surface conditions on the flexural strength of borosilicate glass. J Am Ceram Soc 92(6):1287–1295

    Article  Google Scholar 

  38. Lee HU, Cho D-W, Ehmann KF (2008) A mechanistic model of cutting forces in micro-end-milling with cutting-condition-independent cutting force coefficients. J Manuf Sci Eng 130(3):031102

    Article  Google Scholar 

Download references

Funding

The authors are grateful to the Fundamental Research Grant Scheme (FRGS14-120-0361) for funding this study.

Author information

Authors and Affiliations

  1. Department of Manufacturing and Materials Engineering, Kulliyyah of Engineering, International Islamic University Malaysia, Jalan Gombak, 53100, Kuala Lumpur, Malaysia

    Mst. Nasima Bagum, Mohamed Konneh & A. K. M. Nurul Amin

Authors
  1. Mst. Nasima Bagum
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Mohamed Konneh
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. K. M. Nurul Amin
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Mst. Nasima Bagum.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Bagum, M.N., Konneh, M. & Nurul Amin, A.K.M. Prediction and experimental validation of temperature rise in ductile mode end milling of soda-lime glass. Int J Adv Manuf Technol 96, 3437–3447 (2018). https://doi.org/10.1007/s00170-018-1833-0

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-018-1833-0

Keywords

Search

Navigation