Skip to main content
SpringerLink
Log in

An embedded multi-sensor system on the rotating dynamometer for real-time condition monitoring in milling

The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Cite this article

Abstract

The newly developed multi-sensor system for a milling process sensor system is capable of simultaneously measuring six channels of machining signals using a rotating tool incorporating a wireless system. Furthermore, the system can be used to measure the spindle torque, T q ; tool vibration in the z-axis, A z ; tool tip temperature, T m and the three components of the cutting force. Cutting force signals are generated by using a cross-beam-legged transducer embedded in the standard milling tool holder. A mini accelerometer is placed under the force transducer, whereas a thermocouple is positioned under a cutting tool insert close to the cutting edge. All signals are collected and sent to the data logger system via an inductive wireless transmitter unit incorporated into the standard rotating tool holder. The calibration, verification and real experimental machining test results reveal that the sensor system is both suitable and reliable for measuring machining signals. The measured signals are found to be importantly related to changes in the flank wear state. Therefore, this system can be used for real-time tool condition monitoring in the milling process.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

References

  1. Rehorn AG, Jiang J, Orban PE (2005) State-of-the-art methods and results in tool condition monitoring: a review. Int J Adv Manuf Tecnol 26:693–710

    Article  Google Scholar 

  2. Abellan-Nebot JV, Subirón FR (2010) A review of machining monitoring systems based on artificial intelligence process models. Int J Adv Manuf Tecnol 47:237–257

    Article  Google Scholar 

  3. Teti R, Jemielniak K, O’Donnell G, Dornfeld D (2010) Advanced monitoring of machining operations. CIRP Annals - Manuf Technol 59:717–739

    Article  Google Scholar 

  4. Sick B (2002) On-line and indirect tool wear monitoring in turning with artificial neural networks: a review of more than a decade of research. Mech Syst Signal Process 16(4):487–546

    Article  Google Scholar 

  5. Korkut I (2003) A dynamometer design and its construction for milling operation. Mater Des 24:631–637

    Article  Google Scholar 

  6. Yaldız S, Unsacar F, Saglam H, Isık H (2007) Design, development and testing of a four-component milling dynamometer for the measurement of cutting force and torque. Mech Syst Signal Process 21:1499–1511

    Article  Google Scholar 

  7. Oliveira JFG, Valente CMO (2004) Fast grinding process control with AE modulated power signals. CIRP Annals - Manuf Technol 53(1):267–270

    Article  Google Scholar 

  8. Shao H, Shi X, Li L (2011) Power signal separation in milling process based on wavelet transform and independent component analysis. Int J Mach Tools Manuf 51:701–710

    Article  Google Scholar 

  9. Shi X, Wang R, Chen Q, Shao H (2014) Cutting sound signal processing for tool breakage detection in face milling based on empirical mode decomposition and independent component analysis. J Vib Control doi. https://doi.org/10.1177/1077546314522826

  10. Kalvoda T, Hwang Y-R (2010) A cutter tool monitoring in machining process using Hilbert–Huang transform. Int J Mach Tools Manuf 50:495–501

    Article  Google Scholar 

  11. O’Donnell G, Young P, Kelly K, Byrne G (2001) Towards the improvement of tool condition monitoring systems in the manufacturing environment. J Mater Process Technol 119(1–3):133–139

    Article  Google Scholar 

  12. Suprock CA, Fussell BK, Hassan RZ, Jerard RB A low cost wireless tool tip vibration sensor for milling. In: ASME (ed) The International Manufacturing Science and Engineering Conference (MSEC2008), Evanston, IL, USA, 7–10 October 2008 2008. ASME, pp 1–10

  13. Coz GL, Marinescu M, Devillez A, Dudzinski D, Velnom L (2012) Measuring temperature of rotating cutting tools: application to MQL drilling and dry milling of aerospace alloys. Appl Therm Eng 36:434–441

    Article  Google Scholar 

  14. Kerrigan K, Thil J, Hewison R, O’Donnell GE (2012) An integrated telemetric thermocouple sensor for process monitoring of CFRP milling operations. Procedia CIRP 1:449–454

    Article  Google Scholar 

  15. Totis G, Wirtz G, Sortino M, Veselovac D, Kuljanic E, Klocke F (2010) Development of a dynamometer for measuring individual cutting edge forces in face milling. Mech Syst Signal Process 24:1844–1857

    Article  Google Scholar 

  16. Ma L, Melkote SN, Castle JB (2014) PVDF sensor-based monitoring of milling torque. Int J Adv Manuf Tecnol 70(9–12):1603–1614

    Article  Google Scholar 

  17. Rizal M, Ghani JA, Nuawi MZ, Haron CHC (2015) Development and testing of an integrated rotating dynamometer on tool holder for milling process. Mech Syst Signal Process 52-53:559–576

    Article  Google Scholar 

  18. Qin Y, Zhao Y, Li Y, Zhao Y, Wang P (2017) A novel dynamometer for monitoring milling process. Int J Adv Manuf Tecnol DOI. https://doi.org/10.1007/s00170-017-0292-3:1-9

  19. Xie Z, Lu Y, Li J (2017) Development and testing of an integrated smart tool holder for four-component cutting force measurement. Mech Syst Signal Process 93:225–240

    Article  Google Scholar 

  20. Suprock CA, Nichols JS (2009) A low cost wireless high bandwidth transmitter for sensor-integrated metal cutting tools and process monitoring. Inter J Mechatron Manuf Sys:441–454

  21. Ma L, Melkote SN, Morehouse JB, Castle JB, Fonda JW (2010) On-line monitoring of end milling forces using a thin film based wireless sensor module. In: ASME (ed) Proceedings of the ASME International manufacturing science and engineering conference, Erie, Pennsylvania, USA, October 12–15, 2010 2010. ASME,

  22. Orhan S, Er AO, Camuscu N, Aslan E (2007) Tool wear evaluation by vibration analysis during end milling of AISI D3 cold work tool steel with 35 HRC hardness. NDT&E International 40(2):121–126

    Article  Google Scholar 

  23. Haber RE, Jiménez JE, Peres CR, Alique JR (2004) An investigation of tool-wear monitoring in a high-speed machining process. Sens Actuators, A 116(3):539–545

    Article  Google Scholar 

  24. Kuljanic E, Sortino M (2005) TWEM, a method based on cutting forces—monitoring tool wear in face milling. Int J Mach Tools Manuf 45:29–34

    Article  Google Scholar 

  25. Schulze V, Becke C, Weidenmann K, Dietrich S (2011) Machining strategies for hole making in composites with minimal workpiece damage by directing the process forces inwards. J Mater Process Technol 211(3):329–338

    Article  Google Scholar 

  26. Dini G, Tognazzi F (2007) Tool condition monitoring in end milling using a torque-based sensorized toolholder. Proc Inst Mech Eng Part B J Eng Manuf 221:11–23

    Article  Google Scholar 

  27. Kaya B, Oysu C, Ertunc HM (2011) Force-torque based on-line tool wear estimation system for CNC milling of Inconel 718 using neural networks. Adv Eng Softw 42:76–84

    Article  Google Scholar 

  28. Rizal M, Ghani JA, Nuawi MZ, Haron CHC (2014) A wireless system and embedded sensors on spindle rotating tool for condition monitoring. Adv Sci Lett 20(10–12):1829–1832

    Article  Google Scholar 

  29. Lin S, Peng F, Wen J, Liu Y, Yan R (2013) An investigation of workpiece temperature variation in end milling considering flank rubbing effect. Int J Mach Tools Manuf 73:71–86

    Article  Google Scholar 

  30. Choudhury SK, Bartarya G (2003) Role of temperature and surface finish in predicting tool wear using neural network and design of experiments. Int J Mach Tools Manuf 43(7):747–753

    Article  Google Scholar 

Download references

Funding

The authors wish to thank the Government of Malaysia (MOSTI) through Universiti Kebangsaan Malaysia (UKM) for their financial support under Grant 03-01-02-SF0843 and the Ministry of Research, Technology and Higher Education of the Republic of Indonesia.

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Faculty of Engineering, Syiah Kuala University (UNSYIAH), 23111 Darussalam, Banda Aceh, Indonesia

    Muhammad Rizal

  2. Department of Mechanical and Materials Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, UKM, 43600, Bangi, Selangor, Malaysia

    Jaharah A. Ghani, Mohd Zaki Nuawi & Che Hassan Che Haron

Authors
  1. Muhammad Rizal
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Jaharah A. Ghani
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Mohd Zaki Nuawi
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Che Hassan Che Haron
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Muhammad Rizal.

Rights and permissions

Reprints and Permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Rizal, M., Ghani, J.A., Nuawi, M.Z. et al. An embedded multi-sensor system on the rotating dynamometer for real-time condition monitoring in milling. Int J Adv Manuf Technol 95, 811–823 (2018). https://doi.org/10.1007/s00170-017-1251-8

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-017-1251-8

Keywords

search

Navigation