Abstract
Creep-age forming (CAF) is one of the effective techniques to fabricate extra-large integral airframe panels due to its good forming ability. However, few experimental researches have been conducted on stiffened panel with complex structures under creep-aging condition. In this work, a 1096 × 792-mm stiffened panel with typical structure features, such as stiffeners, the base plate with variable thickness, and the opening, has been formed on the tool of variable curvature at 165 °C for 10 h. Springback of the stiffened panel in static loading process is 91.1%, while it decreases to 82.3% after 10-h creep aging, which shows that plastic and creep deformation play an equivalent role in restraining the springback of the panel. Deformation of the stiffened panel concentrates around the opening with thicker plate and larger curvature, while little deformation occurs in the base plate with varied thickness or stiffeners. It indicates that the size, orientation, and position of the structure features all have significant impact on final shape of the stiffened panel. The accuracy of the corresponding finite element (FE) simulation has been verified by the fact that the proportion of the area, where the gap between the simulated and the experimental part is less than 0.6 mm, accounts for more than 90%.
Article PDF
References
Yan Y, Wang HB, Wan M (2011) Prediction of fracture in press bend forming of aluminum alloy high-stiffener integral panels. Comp Mater Sci 50:2232–2244
Eberl F, Gardiner S, Campanile G, Surdon G, Venmans M, Rrangnell P (2008) Ageformable panels for commercial aircraft. Proc Inst Mech Eng Part G: J Aerosp Eng 222:873–886
Chu GN, Liu G, Li W (2015) Practicality and formability of integrally stiffened tube hydro-assisted forming. Int J Adv Manuf Technol 83:657–664
Lam ACL, Shi ZS, Lin JG, Huang X, Zeng YS, Dean T (2015) A method for designing lightweight and flexible creep-age forming tools using mechanical splines and sparse controlling points. Int J Adv Manuf Technol 80:361–372
Jeunechamps PP, Ho KC, Lin J (2006) A closed form technique to predict springback in creep age-forming. Int J Mech Sci 48:621–629
Zhan L, Lin J, Dean TA (2011) A review of the development of creep age forming: experimentation, modelling and applications. Int J Mach Tools Manuf 51:1–17
Jeshvaghani RA, Zohdi H, Shahverdi HR, Bozorg M, Hadavi SMM (2012) Influence of multi-step heat treatments in creep age forming of 7075 aluminum alloy: optimization for springback, strength and exfoliation corrosion. Mater Charact 73:8–15
Zhang J, Deng YL, Li SY, Chen ZY, Zhang XM (2013) Creep age forming of 2124 aluminum alloy with single/double curvature. Trans Nonferrous Met Soc China 23:1922–1929
Ho KC, Lin J, Dean TA (2004) Modeling of springback in creep forming thick aluminum sheets. Int J Plast 20:733–751
Li HY, Lu XC (2015) Springback and tensile strength of 2A97 aluminum alloy during age forming. Trans Nonferrous Met Soc China 25:1043–1049
Lam ACL, Shi ZS, Lin J, Huang X (2015) Influences of residual stress and initial distortion on springback prediction of 7B04-T651 aluminum plates in creep-age forming. Int J Mech Sci 103:115–126
Huang L, Wan M (2008) Compensation algorithm for springback in age forming for aluminum alloy plate. Acta Aeronautica et Astronautica Sinica 29:1406–1410
Jesvaghani RA, Emami M, Shahverdi HR, Hadav SMM (2011) Effects of time and temperature on the creep forming of 7075 aluminum alloy: springback and mechanical properties. Mater Sci Eng A 528:8795–9799
Khamneh ME, Paykani MA, Shahverdi H, Hadavi SMM, Emami M (2016) Optimization of spring-back in creep age forming process of 7075 Al-Alclad alloy using D-optimal design of experiment method. Measurement 88:278–286
Guines D, Gavrus A, Ragneau E (2008) Numerical modeling of integrally stiffened structures forming from creep age forming technique. Int J Mater Form 1:1071–1074
Inforzato DJ, Junior PRC, Fernandez FF, Travessa DN (2012) Creep-age forming of A7475 aluminum panels for aircraft lower wing skin application. Mater Charact 15:596–602
Zhan L, Xu XL, Jia SF (2013) Finite element simulation for creep age forming of 7055 aluminum alloy stiffened panel. Chin J Nonferrous Met 23:2104–2109
Lam ACL, Shi ZS, Yang HL, Wan L, Davies CM, Lin J, Zhou SJ (2015) Creep-age forming AA2219 plates with different stiffener designs and pre-form age conditions: experimental and finite element studies. J Mater Process Technol 219:155–163
Huang L, WAN M, Chi CL, Ji X (2007) FEM analysis of spring-backs in age forming of aluminum alloy plates. Chinese J Aeronaut 20:564–569
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Luo, H., Li, W., Li, C. et al. Investigation of creep-age forming of aluminum lithium alloy stiffened panel with complex structures and variable curvature. Int J Adv Manuf Technol 91, 3265–3271 (2017). https://doi.org/10.1007/s00170-017-0004-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0004-z