Skip to main content
SpringerLink
Log in

A study of PSHG and its characteristic mechanism of residual stress within a hardened layer

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

The pre-stressed hardening grinding (PSHG) combines with the advantages of pre-stressed grinding and grinding hardening. In order to study the characteristic of PSHG, especially its residual stress within a hardened layer after PSHG, the PSHG experiment was carried on. Combining with theory and experiment results, the variation and its mechanism of residual stress were studied. The paper shows the PSHG can obtain a hardened layer with controllable residual stress after the process. The residual stress decreases with the increasing of feeding speed and grinding depth. When the grinding depth is small, the tensile residual stress decreases with the increasing of pre-stress. And when the grinding depth is large, the compressive residual stress decreases first and then increases with the increase of pre-stress because of the comprehensive effect of heat and phase transformation. Then, a finite element method (FEM) simulation was performed to study the variation of thermal stress in a hardened layer after PSHG process. Distribution and variation of thermal stress were obtained. In the end, according to the relationship between residual stress and thermal stress, the distribution and variation mechanisms of phase transformation stress were obtained and studied. They vary along with the level of phase transformation. The compressive phase transformation stress increases with the increasing of grinding depth. And due to the pre-stress’s influence on the phase transformation, it decreases first and then increases with the increase of pre-stress.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Nguyen T, Zhang LC, Sun DL, Wu Q (2014) Characterizing the mechanical properties of the hardened layer induced by grinding-hardening. Mech Sci Technol 18(2):277–298

    Article  Google Scholar 

  2. Zhang Y, Ge PQ, Be WB (2015) Plane grind-hardening distortion analysis and the effect to grind-hardening layer. Int J Adv Manuf Technol 78(1-4):431–438

    Article  Google Scholar 

  3. Liu SY, Yang G, Zheng JQ, Liu XH (2015) Numerical and experimental studies on grind-hardening cylindrical surface. Int J Adv Manuf Technol 76(1-4):487–499

    Article  Google Scholar 

  4. Zarudi I, Zhang LC (2002) Mechanical property improvement of quenchable steel by grinding. J Mater Sci 37(18):3935–3943

    Article  Google Scholar 

  5. Xiu SC, Li CH, Cai GQ (2007) Study on surface finish mechanism in quick-point grinding. Int J Comput Appl Technol 29(2):163–167

    Article  Google Scholar 

  6. Zhang L, Ge PQ, Zhang JH (2007) Experiment and simulation on temperature field of 40Cr steel surface layer in grind-hardening. Int J Abras Technol l(2):187–197

    Article  MathSciNet  Google Scholar 

  7. Menenzes P, Kallas S, Lovell M (2011) Role of surface texture, roughness and hardness on friction during unidirectional sliding. Tribol Lett 41(1):1–15

    Article  Google Scholar 

  8. Liu JD, Wang GC, Wang Z, Fan ST (2006) Experimental research on grind-hardening of 65Mn steel. Mater Sci Forum 505–507(2):787–791

    Article  Google Scholar 

  9. Salonitis K, Kolios A (2015) Experimental and numerical study of grind-hardening-induced residual stresses on AISI 1045 Steel. Int J Adv Manuf Technol 79(9-12):1443–1452

    Article  Google Scholar 

  10. Qin MY, Ye BY, Jia X, He AD (2013) Experimental investigation of residual stress distribution in pre-stress cutting. Int J Adv Manuf Technol 65(1-4):355–361

    Article  Google Scholar 

  11. Li CH, Zhang XW, Zhang Q, Wang S, Zhang DK, Jia DZ, Zhang YB (2014) Modeling and simulation of useful fluid flow rate in grinding. Int J Adv Manuf Technol 75(9-12):1587–1604

    Article  Google Scholar 

  12. Martell JJ, Liu CR, Shi J (2014) Experimental investigation on variation of machined residual stresses by turning and grinding of hardened AISI 1053 steel. Int J Adv Manuf Technol 74(9-12):1381–1392

    Article  Google Scholar 

  13. Evans A, Kim SB, Shackleton J, Bruno G, Preuss M, Wither PJ (2005) Relaxation of residual stress in shot peened Udimet 720Li under high temperature isothermal fatigue. Int J Fatigue 27(10-12):1530–1534

    Article  Google Scholar 

  14. Zurita O, Acosta A, Moreno D (2003) Superficial hardening in the plane grinding of AISI 1045 steel. J Mater Eng Perform 12(3):298–303

    Article  Google Scholar 

  15. Karabelchtchikova O, Rivero IV, Hsiang SM (2008) Model of residual stress distribution in D2 steel via grinding dynamics using a second-order damping system. J Mater Process Technol 1–3(198):313–322

    Article  Google Scholar 

  16. Jin K, Jeong T, Kim T, Kim N, Kim B (2014) Analysis and design for reducing residual stress and distortion after ejection of injection molded part with metal-insert. Int J Precis Eng Manuf 15(12):2533–2542

    Article  Google Scholar 

  17. Choi Y (2009) A comparative study of residual stress distribution induced by hard machining versus grinding. Tribol Lett 3(36):277–284

    Article  Google Scholar 

  18. Tönissen S, Klocke F, Feldhaus B, Buchholz S, Weiss M (2012) Residual stress prediction in quick point grinding. Prod Eng 3(6):243–249

    Article  Google Scholar 

  19. Huang XM, Zhou ZX, Ren YH, Mao C, Li W (2013) Experimental research material characteristics effect on white layers formation in grinding of hardened steel. Int J Adv Manuf Technol 66(9-12):1555–1561

    Article  Google Scholar 

  20. Slowinski B, Nadolny K (2007) Effective manufacturing method for automated inside diameter grinding. J Adv Mech Des, Syst, Manuf 1(4):472–480

    Google Scholar 

  21. Xiu SC, Shi XL (2015) Transformation mechanism of microstructure and residual stress within hardening layer in PSHG. J Adv Mech Des, Syst, Manuf 9(3):1–13

    Google Scholar 

  22. Qian Z, Chumbley LS, Johnson E (2011) The effect of specimen dimension on residual stress relaxation of carburized and quenched steels. Mater Sci Eng A 529:246–252

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Northeastern University, Shenyang, Liaoning, China

    Xiaoliang Shi, Shichao Xiu, Xiuming Zhang & Yushi Wang

Authors
  1. Xiaoliang Shi
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Shichao Xiu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Xiuming Zhang
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Yushi Wang
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Shichao Xiu.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Shi, X., Xiu, S., Zhang, X. et al. A study of PSHG and its characteristic mechanism of residual stress within a hardened layer. Int J Adv Manuf Technol 88, 863–877 (2017). https://doi.org/10.1007/s00170-016-8835-6

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-016-8835-6

Keywords

Search

Navigation