In this study, the electric hot incremental forming (EHIF) process was experimentally and numerically investigated on the Ti-6Al-4V sheet. The effect of process parameters, such as wall angle, step size, and tool diameter, was investigated on the formability, incremental forming force, and thickness distribution of samples. The results demonstrated that the incremental forming force increases with increasing the step size and decreasing the tool diameter. Also, the thickness of formed samples decreases with increasing the wall angle and decreasing the step size. In addition, the finite element modeling was used to compare the experimental and numerical results. The numerical prediction of forming force and thickness distribution was obtained and compared with experimental results and showed a good agreement.
This is a preview of subscription content, access via your institution.
Buy single article
Instant access to the full article PDF.
Tax calculation will be finalised during checkout.
Matsubara S (1994) Incremental backward bulge forming of a sheet metal with a hemispherical-head tool. J JSTP 35:1311–1316
Hussain G, Gao L, Zhang ZY (2008) Formability evaluation of a pure titanium sheet in the cold incremental forming process. Int J Adv Manuf Technol 37:920–926
Aerens R, Eyckens P, Van Bael A, Duflou JR (2010) Force prediction for single point incremental forming deduced from experimental and FEM observations. Int J Adv Manuf Technol 46:969–982
Li J, Hu J, Pan J, Geng P (2012) Thickness distribution and design of a multi-stage process for sheet metal incremental forming. Int J Adv Manuf Technol 62:981–988
Mirnia MJ, Mollaei Dariani B, Vanhove H, Duflou JR (2014) Thickness improvement in single point incremental forming deduced by sequential limit analysis. Int J Adv Manuf Technol 70(9-12):2029–2041
Lee HS, Yoon JH, Park CH, Ko YG, Shin DH (2007) A study on diffusion bonding of superplastic Ti-6Al-4V ELI grade. J Mater Process Technol 187–188:526–529
Ghosh AK, Hamilton CH (1979) Mechanical behavior and hardening characteristics of a superplastic Ti-6A1-4V alloy. Metall Trans A 10A:699–706
Vanderhasten M, Rabet L, Verlinden B (2008) Ti-6Al-4V: deformation map and modelisation of tensile behaviour. Mater Des 29:1090–1098
Ambrogio G, Filice L, Manco GL (2008) Warm incremental forming of magnesium alloy AZ31. CIRP Ann Manuf Technol 57:257–260
Hussain G, Gao L, Hayat N, Dar U (2010) The formability of annealed and pre-aged AA-2024 sheets in single-point incremental forming. Int J Adv Manuf Technol 46:543–549
Lee HS, Huda Z, Iskandar Taibb N, Zahariniea T (2009) Characterization of 2024-T3: an aerospace aluminum alloy. Mater Chem Phys 113:515–517
Duflou JR, Callebaut B, Verbert J, De Baerdemaeker H (2007) Laser assisted incremental forming: formability and accuracy improvement. Ann CIRP 56:273–276
Fan G, Gao L, Hussain G, Wu Z (2008) Electric hot incremental forming: a novel technique. Int J Mach Tools Manuf 48:1688–1692
Fan G, Sun F, Meng X, Gao L, Tong G (2010) Electric hot incremental forming of Ti–6Al–4V titanium sheet. Int J Adv Manuf Technol 49:941–947
Ambrogio G, Filice L, Gagliardi F (2012) Formability of lightweight alloys by Hot incremental sheet forming. Mater Des 34:501–508
Hussain G, Gao L (2007) A novel method to test the thinning limits of sheet metals in negative incremental forming. Int J Mach Tools Manuf 47:419–435
Kiranli E (2009) Determination of material constitutive equation of a biomedical grade Ti6Al4V alloy for cross-wedge rolling. A thesis submitted to the graduate school of engineering and sciences of Izmir institute of technology in partial fulfillment of the requirements for the degree of master of science in material science
Chen G, Ren C, Yang X, Jin X, Guo T (2011) Finite element simulation of high-speed machining of titanium alloy (Ti–6Al–4V) based on ductile failure model. Int J Adv Manuf Technol 56:1027–1038
Liu R, Melkote S, Pucha R, Morehouse J, Man X, Marusich T (2013) An enhanced constitutive material model for machining of Ti–6Al–4V alloy. J Mater Process Technol 213:2238–2246
About this article
Cite this article
Honarpisheh, M., Abdolhoseini, M.J. & Amini, S. Experimental and numerical investigation of the hot incremental forming of Ti-6Al-4V sheet using electrical current. Int J Adv Manuf Technol 83, 2027–2037 (2016). https://doi.org/10.1007/s00170-015-7717-7
- Hot incremental forming
- Forming force
- Thickness distribution
- FE simulation