Abstract
This paper proposes a systematic optimization model of process parameters in plastic injection molding (PIM). Firstly, the Taguchi method is employed for experimentation and data analysis, in which the quality characteristics for the plastic injection product are length and warpage. The control factors for the process are melt temperature, injection velocity, packing pressure, packing time, and cooling time. Moreover, the signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are used to obtain a combination of parameter settings. Experimental data are set for the response surface methodology (RSM) in order to analyze and create two quality predictors and two S/N ratio predictors. The two quality predictors are associated with genetic algorithms (GA) to search for an optimal combination of process parameters that meets multiple-objective quality characteristics. Finally, four predictors are combined with the hybrid GA-PSO to find the final optimal combination of process parameters. The confirmation results show that the proposed model not only enhances the stability in the injection molding process, including the quality in length and warpage, but also reduces the costs of and time spent in the PIM process.
Similar content being viewed by others
References
Wu CH, Chen WS (2006) Injection molding and injection compression molding of three-beam grating of DVD pickup lens. Sensors Actuators A Phys 125(2):367–375
Teng Y, Xu Y (2008) Culture condition improvement for whole-cell lipase production in submerged fermentation by Rhizopus chinensis using statistical method. Bioresour Technol 99(9):3900–3907
Aggarwal A, Singh H, Kumar P, Singh M (2008) Optimizing power consumption for CNC turned parts using response surface methodology and Taguchi’s technique—a comparative analysis. J Mater Process Technol 200(1–3):373–384
Kurt M, Bagci E, Kaynak A (2009) Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes. Int J Adv Manuf Technol 40(5–6):458–469
Altan M (2010) Reducing shrinkage in injection moldings via the Taguchi ANOVA and neural network method. Mater Des 31:599–640
Zhai M, Xie Y (2010) A study of gate location optimization of plastic injection molding using sequential linear programming. Int J Adv Manuf Technol 49(14):97–103
Ng CF, Kamaruddin S, Siddiquee AN, Khan ZA (2011) Experimental investigation on the recycled HDPE and optimization of injection moulding process parameters via Taguchi method. Int J Mech Mater Eng 6(1):81–91
Öktem H (2012) Optimum process conditions on shrinkage of an injected-molded part of DVD-ROM cover using Taguchi robust method. Int J Adv Manuf Technol 61:518–528
Wang X, Zhao G, Wang G (2013) Research on the reduction of sink mark and warpage of the molded part in rapid heat cycle molding process. Mater Des 47:779–792
Shi F, Lou ZL, Lu JG, Zhang YQ (2003) Optimization of plastic injection molding process with soft computing. Int J Adv Manuf Technol 21:656–661
Yin F, Mao H, Hua L (2011) A hybrid of back propagation neural network and genetic algorithm for optimization of injection molding process parameters. Mater Des 32:3457–3464
Ozcelik B, Erzurumlu T (2006) Comparison of the warpage optimization in the plastic injection molding using ANOVA, neural network model and genetic algorithm. J Mater Process Technol 171(3):437–445
Akbarzadeh A, Sadeghi M (2011) Parameter study in plastic injection molding process using statistical methods and IWO algorithm. Int J Model Optim 1(2):141–145
Chen WC, Kurniawan D, Fu GL (2012) Optimization of process parameters using DOE, RSM and GA in plastic injection molding. Adv Mater Res 472–475:1220–1223
Chen WC, Wang MW, Chen CT, Fu GL (2009) An integrated parameter optimization system for MISO plastic injection molding. Int J Adv Manuf Technol 44:501–511
Kurtaran H, Erzurumlu T (2006) Efficient warpage optimization of thin shell plastic parts using response surface methodology and genetic algorithm. Int J Adv Manuf Technol 27(5–6):468–472
Park HS, Dang XP (2010) Optimization of conformal cooling channels with array of baffles for plastic injection mold. Int J Precis Eng Manuf 11(6):879–890
Sun B, Wu Z, Gu B, Huang X (2010) Optimization of injection molding process parameters based on response surface methodology and genetic algorithms. In: Proc of the int’l conf. on computer engineering and technology, pp 397–400
Zhao P, Zhou H, Li Y, Li D (2010) Process parameter optimization of injection molding using a fast strip analysis as a surrogate model. Int J Adv Manuf Technol 49:949–959
Xu G, Yang Z, Long G (2012) Multi-objective optimization of MIMO plastic injection molding process conditions based on particle swarm optimization. Int J Adv Manuf Technol 58:521–531
Mostafa JJ, Mohammad MA, Ehsan M (2011) A hybrid response surface methodology and simulated annealing algorithm: a case study on the optimization of shrinkage and warpage of a fuel filter. World Appl Sci J 13(10):2156–2163
Tzeng CJ, Chen RY (2013) Optimization of electric discharge machining process using the response surface methodology and genetic algorithm approach. Int J Precis Eng Manuf 14(5):709–717
Chen WC, Fu GL, Tai PH, Deng WJ (2009) Process parameter optimization for MIMO plastic injection molding via soft computing. Expert Syst Appl 36:1114–1122
Tzeng CJ, Yang YK, Lin YH, Tsai CH (2012) A study of optimization of injection molding process parameters for SGF and PTFE reinforced PC composites using neural network and response surface methodology. Int J Adv Manuf Technol 63:691–704
Huang HX, Li JC, Xiao CL (2015) A proposed iteration optimization approach integrating back-propagation neural network with genetic algorithm. Expert Syst Appl 42:146–155
Jordehi R (2015) Enhanced leader PSO (ELPSO): a new PSO variant for solving global optimisation problems. Appl Soft Comput 26:401–417
Ranjania M, Murugesan P (2015) Optimal fuzzy controller parameters using PSO for speed control of Quasi-Z Source DC/DC converter fed drive. Appl Soft Comput 27:332–356
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Chen, WC., Nguyen, MH., Chiu, WH. et al. Optimization of the plastic injection molding process using the Taguchi method, RSM, and hybrid GA-PSO. Int J Adv Manuf Technol 83, 1873–1886 (2016). https://doi.org/10.1007/s00170-015-7683-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-7683-0