Abstract
The popularity of composite materials is continuously growing with new varieties being developed and tested with different machining processes to establish their suitability. Destructive as well as non-destructive methods, such as ultrasonics, X-ray radiography and eddy-current, have previously been used to ensure that the combination of particular machining methods and composites provide the required quality that can allow the required lifespan of the final product. X-ray computed tomography (CT) is applied as a novel method in this paper to obtain quantitative data about the inner and outer structures of carbon fibre reinforced polymer (CFRP) drilled holes providing more information than any other non-contact and non-destructive evaluation. This is combined with precise measurements from optical CMM and image processing for a full analysis for the entire part. This method can provide accurate measurements for all the layers of the CFRP and very little interaction from the operator minimising the human error. The method complies with VDI/VDE 2630 standard and the quality of the acquired measurements is assured. The results can assist in establishing the best machining process, provide accurate measurements of diameter, circularity and positioning of the hole and information about delaminated areas.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Adams RD, Cawley P (1988) A review of defect types and nondestructive testing techniques for composites and bonded joints. NDT Int 21:208–222
Teti R (2002) Machining of composite materials. CIRP Ann Manuf Technol 51:611–634
Pejryd L, Beno T, Carmignato S (2014) Computed tomography as a tool for examining surface integrity in drilled holes in cfrp composites. In: 2nd CIRP Conference on Surface Integrity (CSI), vol 13, pp 43–48
Grilo TJ, Paulo RMF, Silva CRM, Davim JP (2013) Experimental delamination analyses of CFRPs using different drill geometries. Compos Part B 45:1344–1350
Persson E, Eriksson I, Zackrisson L (1997) Effects of hole machining defects on strength and fatigue life of composite laminates. Compos Part A 28A:141–151
Santhanakrishnan G, Krishnamurthy R, Malhotra SK (1988) Machinability characteristics of fibre reinforced plastics composites. J Mech Work Technol 17:195–204
Davim JP, Reis P (2003) Study of delamination in drilling carbon fiber reinforced plastics (CFRP) using design experiments. Compos Struct 59:481–487
Makhdum F, Norddin DNP, Roy A, Silberschmidt VV (2012) Ultrasonically assisted drilling of carbon fibre reinforced plastics. Solid State Phenom 188:170–175
Tsao CC, Hocheng H (2004) Taguchi analysis of delamination associated with various drill bits in drilling of composite material. Int J Mach Tools Manuf 44:1085–1090
Abrate S, Walton DA (1992) Machining of composite materials. Part I: Traditional methods. Compos Manuf 3:75–83
Hocheng H, Tsao CC (2003) Comprehensive analysis of delamination in drilling of composite materials with various drill bits. J Mater Process Technol 140:335–339
Stone R, Krishnamurthy K (1996) A neural network thrust force controller to minimize delamination during drilling of graphite epoxy laminates. Int J Mach Tools Manuf 36:985–1003
Gaitonde VN, Karnik SR, Rubio JC, Correia AE, Abrao AM, Davim JP (2008) Analysis of parametric influence on delamination in high speed drilling of carbon fiber reinforced plastic composites. J Mater Process Technol 203:431–438
Abrao AM, Faria PE, Rubio JCC, Reis P, Davim JP (2007) Drilling of fiber reinforced plastics: A review. J Mater Process Technol 186:1–7
Marques AT, Durao LM, Magalhaes AG, Silva JF, Tavares JMRS (2009) Delamination analysis of carbon fibre reinforced laminates: Evaluation of a special step drill. Compos Sci Technol 69:2376–2382
Anand RS, Patra K, Stiner M (2014) Size effects in micro drilling of carbon fiber reinforced plastic composite. Prod Eng Res Devel 8:301–307
Lau WS, Yue TM, Lee TC, Lee WB (1995) Un-conventional machining of composite materials. J Mater Process Technol 48:199–205
Piquet R, Ferret B, Lachaud F, Swider P (2000) Experimental analysis of drilling damage in thin carbon/epoxy plate using special drills. Compos Part A 31:1107–1115
Park KY, Choi JH, Lee DG (1995) Delamination-free and high efficiency drilling of carbon fiber reinforced plastics. J Compos Mater 29:1988–2002
Mohan NS, Ramachanda A, Kulkrni SM (2005) Influence of process paramaters on cutting force and torque during drilling of glass-fiber polyester reinforced composites. Compos Struct 71:407–413
Gupta A, Barnes S, McEwen I, Kourra N, Williams MA (2014) Study of cutting speed variation in the ultrasonic assisted drilling of carbon fibre composites. In: Proceeding of the ASME international mechanical engineering congress & exposition, IMECE, vol 14
Goeje MP, Wapenaar KED (1992) Non-destructive inspection of carbon fibre-reinforced plastics using eddy current methods. Composites 23:147–157
Pye CJ, Adams RD (1981) Detection of damage in fibre reinforced plastics using thermal field generated during resonant vibration. NDT Int 14:111–118
Mook G, Lange R, Koeser O (2001) Non-destructive characterisation of carbon-fibre-reinforced plastics by means of eddy-currents. Compos Sci Technol 61:865–873
Mouritz AP, Townsend C, Shah Khan MZ (2000) Non-destructive detection of fatigue damage in thick composites by pulse-echo ultrasonics. Compos Sci Technol 60:23–32
Steinberger R, Valagas Leitao TI, Ladstatter E, Pinter G, Billinger W, Lang RW (2006) Infrared thermographic techniques for non-destructive damage characterization of carbon fibre reinforced polymers during tensile fatigue testing. Int J Fatigue 28:1340–1347
Davim JP, Rubio JC, Abrao AM (2007) A novel approach based on digital image analysis to evaluate the delamination factor after drilling composite laminates. Compos Sci Technol 67:1939–1945
Seif MA, Khashaba UA, Rojas-Oviedo R (2007) Measuring delamination in carbon/epoxy composites using a shadow moire laser based imaging technique. Compos Struct 79:113–118
Raisutis R, Kazys R, Zukauskas E, Mazeika L, Vladisauskas A (2010) Application of ultrasonic guided waves for non-destructive testing of defective CFRP rods with multiple delaminations. NDT E Int 43:416–424
Herman GT (2009) Fundamentals of computed tomography - image reconstruction from projections. Springer, London
Hsieh J (2009) Computed tomography -principles, design, artifacts, and recent advances, 2nd edn. SPIE Press, Washington
Kruth JP, Bartscher M, Carmignato S, Schmitt R, De Chiffre L, Weckenmann A (2011) Computed tomography for dimensional metrology. CIRP Ann Manuf Technol 60:821–842
Sun W, Brown SB, Leach RK (2012) An overview of industrial X-ray computed tomography. Queen’s Printer and Controller of HMSO
Welkenhuyzen F, Kiekens K, Pierlet M, Dewulf W, Bleys P, Kruth JP, Voet A (2009) Industrial Computer Tomography for dimensional metrology: Overview of influence factors and improvement strategies. In: OPTIMESS conference
Kumar J, Attridge A, Wood PKC, Williams MA (2011) Analysis of the effect of cone-beam geometry and test object configuaration on the measurement accuracy of a computed tomography scanner used for dimensional measurement. Meas Sci Technol 22:35105–35120
Hiller J, Maisl M, Reindl LM (2012) Physical characterization and performance evaluation of an X-ray micro-computed tomography system for dimensional metrology applications. Meas Sci Technol 23:85404–85422
Weib D, Lonardoni R, Deffner A, Kuhn C (2012) Geometric image distortion in flat-panel X-ray detectos and its influence on the accuracy of CT-based dimensional measurements. In: iCT conference
Dewulf W, Kiekens K, Tan Y, Welkenhuyzen F, Kruth JP (2013) Uncertainty determination and quantification for dimensional measurements with industrial computed tomography. CIRP Ann Manuf Technol 62:535–538
Computed tomography in dimensional measurements. Measurement procedure and comparability. VDI/VDE 2630 Part 1.4 (2010)
Lifton JJ, Malcolm AA, McBride JW, Cross KJ (2013) The application of voxel size correction in X-ray Computed Tomography for dimensional metrology. In: Singapore international NDT conference & exhibition
Sivasankar S, Jeyapaul R, Kolappan S, Shaadil NM (2012) Procedural study for roughness, roundness and waviness measurement of EDM drilled holes using image processing technology. Comput Model Inf Process 16:49–63
Kourra N, Williams MA, Attridge A, Warnett J, Barnes S, Gupta A (2014) Analysis of drilled holes on carbon fibre material with X-ray computed tomography. In: IEEE international workshop on metrology for aerospace
Silva D, Teixera JP, Machado CM (2014) Methodology analysis for evaluation of drilling-induced damage in composites. Int J Manuf Technol 71:1919–1928
Krulikowski A (1997) Form controls, fundamentals of geometric dimensioning & tolerancing. Effective Training Inc., Wayne, pp 71–110
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (https://creativecommons.org/licenses/by/4.0), which permits use, duplication, adaptation, distribution, and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Kourra, N., Warnett, J.M., Attridge, A. et al. Metrological study of CFRP drilled holes with x-ray computed tomography. Int J Adv Manuf Technol 78, 2025–2035 (2015). https://doi.org/10.1007/s00170-014-6734-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-014-6734-2