Abstract
In this study, friction stir welding (FSW) technique was employed for joining AZ31 magnesium plates. Since SiC particles had been injected along the joint line, AZ31/SiC nano-composite was developed in the stir zone (SZ). To find the optimum condition, FSW was conducted under the combination of three rotational and two traveling speeds. Microstructural investigations were carried out through optical and scanning electron microscopes. Onion ring structure consisting SiC-rich and SiC-free regions was observed in SZ. In addition, reasonable particle dispersion happened in the specimen friction stir welded (FSWed) at 800 rpm and 75 mm/min. Thanks to the SiC reinforcements, grain size reduced from 44 μm in base metal to 5 μm in the SZ. Compared to previous researches, microstructural evolution associated with reinforcement particles exerted positive effects on the mechanical properties of the joint. Meanwhile, fracture surfaces of tensile specimens were closely examined and an extreme correlation with ductility results was observed. As expected, on the other hand, composite joints exhibited superior hardnesses to the base metal. Despite indiscernible difference, the foregoing specimen showed the highest hardness.
Similar content being viewed by others
References
Máthis K, Trojanová Z, Lukáč P, Cáceres CH, Lendvai J (2004) Modeling of hardening and softening processes in Mg alloys. J Alloys Compd 378:176–179
Mordike BL, Ebert T (2001) Magnesium properties—applications—potential. Mater Sci Eng A 302:37–45
Sun K, Shi QY, Sun YJ, Chen GQ (2012) Microstructure and mechanical property of nano-SiCp reinforced high strength Mg bulk composites produced by friction stir processing. Mater Sci Eng A 547:32–37
Atwell DL, Barnett MR, Hutchinson WB (2012) The effect of initial grain size and temperature on the tensile properties of magnesium alloy AZ31 sheet. Mater Sci Eng A 549:1–6
Morisada Y, Fujii T, Nagaoka T, Fukusumi M (2006) Effect of friction stir processing with SiC particles on microstructure and hardness of AZ31. Mater Sci Eng A 433:50–54
Kolodziejczaka P, Kalita W (2009) Properties of CO2 laser-welded butt joints of dissimilar magnesium alloys, j mater process tech 209:1122–1128
Dhanapal A, Rajendra Boopathy S, Balasubramanian V (2012) Corrosion behaviour of friction stir welded AZ61A magnesium alloy welds immersed in NaCl solutions. Trans Nonferrous Metals Soc China 22:793–802
Ceschini L, Boromei I, Minak G, Morri A, Tarterini F (2007) Effect of friction stir welding on microstructure, tensile and fatigue properties of the AA7005/10 vol.% Al2O3 composite, Compos. Sci Technol 67:605–615
Ellis MBD (1996) Joining of aluminium based metal matrix composites. Int Mater Rev 41(2):41–58
Bahrami M, Dehghani K, Besharati Givi MK (2014) A novel approach to develop aluminum matrix nano-composite employing friction stir welding technique. Mater Des 53:217–225
Sun YF, Fujii H (2011) The effect of SiC particles on the microstructure and mechanical properties of friction stir welded pure copper joints. Mater Sci Eng A 528:5470–5475
Bahrami M, Helmi N, Dehghani K, Besharati Givi MK (2014) Exploring the effects of SiC reinforcement incorporation on mechanical properties of friction stir welded 7075 aluminum alloy: fatigue life, impact energy, tensile strength. Mater Sci Eng A 595:173–178
Bahrami M, Besharati Givi MK, Dehghani K, Parvin N (2014) On the role of pin geometry in microstructure and mechanical properties of AA7075/SiC nano-composite fabricated by friction stir welding technique. Mater Des 53:519–527
Commin L, Masse JE, Barrallier L (2009) Friction stir welding of AZ31 magnesium alloy rolled sheets: influence of processing parameters. Acta Mater 59:326–334
Faraji G, Asadi P (2011) Characterization of AZ91/alumina nanocomposite produced by FSP. Mater Sci Eng A 527:2320–2330
Zohoor M, Besharati Givi MK, Salami P (2012) Effect of processing parameters on fabrication of Al–Mg/Cu composites via friction stir processing. Mater Des 39:358–365
Barmouz M, Asadi P, Besharati Givi MK, Taherishargh M (2011) Investigation of mechanical properties of Cu/SiC composite fabricated by FSP: effect of SiC particles’ size and volume fraction. Mater Sci Eng A 528:1740–1749
Humphreys FJ, Hatherly M (2004) Recrystalization and related annealing phenomena 2nd ed. Elsevier, Manchester
Lloyd DJ (1994) Particle reinforced aluminium and magnesium matrix composites. Int Mater Rev 39:1–23
Sharifitabar M, Sarani A, Khorshahian S, Shafiee Afarani M (2011) Fabrication of 5052Al/Al2O3 nanoceramic particle reinforced composite via friction stir processing route. Mater Des 32:4164–4172
Hertzberg RW, Vinci RP, Hertzberg JL (2012) Deformation and fracture mechanics of engineering materials 5th ed. Wiley, Michigan
Mishra RS, Ma ZY (2005) Friction stir welding and processing. Mater Sci Eng R 50:1–78
Commin L, Dumont M, Rotinat R, Pierron F, Masse J, Barrallier L (2012) Influence of the microstructural changes and induced residual stresses on tensile properties of wrought magnesium alloy friction stir welds. Mater Sci Eng A 551:288–292
Dieter GE (1986) Mechanical metallurgy 3rd Edition. Mc Graw-Hill, Boston
Azizieh M, Kokabi AH, Abachi P (2011) Effect of rotational speed and probe profile on microstructure and hardness of AZ31/Al2O3 nanocomposites fabricated by friction stir processing. Mater Des 31:2033–2041
Kashani-Bozorg SF, Jazayeri K (2008) Formation of Al/B4C surface nano-composite layers on 7075 Al alloy employing friction stir processing, International Conference on Nanoscience And Nanotechnology 715-719.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Abdolahzadeh, A., Omidvar, H., Safarkhanian, M.A. et al. Studying microstructure and mechanical properties of SiC-incorporated AZ31 joints fabricated through FSW: the effects of rotational and traveling speeds. Int J Adv Manuf Technol 75, 1189–1196 (2014). https://doi.org/10.1007/s00170-014-6205-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-014-6205-9