Abstract
The orthogonal experiment was made for the dry cutting of gray cast iron by coated cemented carbide cutting tool. The regression analysis was made for the experimental data by the least square method. The empirical equation of the cutting force was obtained under the dry cutting condition. The influence rule of the cutting parameters on cutting force was analyzed, and the abrasion modality and mechanism of the tool were studied. The reasonable cutting parameters of the processing of gray cast iron by coated cemented carbide cutting tool under the dry cutting condition were obtained by the analyses of the cutting efficiency versus cutting force of the tools. This study provided a fundamental basis for the optimization of the cutting technological parameters for gray cast iron.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Souza J, Nono M, Ribeiro M, Machado J, Silva O (2009) Cutting forces in turning of gray cast iron using silicon nitride based cutting tool. Mater Des 30(7):2715–2720
Wakaoka S, Yamane Y, Sekiya K, Narutaki N (2002) High-speed and high-accuracy plunge cutting for vertical walls. J Mater Process Tech 127(2):246–250
Gomes J, Miranda A, Silva R, Vieira J (1996) Tribological properties of AlNCeO2-Si3N4 cutting materials in unlubricated sliding against tool steel and cast iron. Mater Sci Eng:A 209(1):277–286
Xu W, Ferry M, Wang Y (2005) Influence of alloying elements on as-cast microstructure and strength of gray iron. Mater Sci Eng:A 390(1):326–333
Ferry M, Xu W (2004) Microstructural and crystallographic features of ausferrite in as-cast gray iron. Mater Charact 53(1):43–49
Nayyar V, Kaminski J, Kinnander A, Nyborg L (2012) An experimental investigation of machinability of graphitic cast iron grades; flake, compacted and spheroidal graphite iron in continuous machining operations. Procedia CIRP 1:488–493
Pouranvari M (2010) On the weldability of grey cast iron using nickel based filler metal. Mater Des 31(7):3253–3258
Sarma D, Dixit U (2007) A comparison of dry and air-cooled turning of grey cast iron with mixed oxide ceramic tool. J Mater Process Tech 190(1):160–172
Klocke F, Eisenblätter G (1997) Dry cutting. CIRP Ann-Manuf Tech 46(2):519–526
de Souza Jr AM, Sales WF, Santos SC, Machado AR (2005) Performance of single Si3N4 and mixed Si3N4+ PCBN wiper cutting tools applied to high speed face milling of cast iron. Int J Mach Tools Manuf 45(3):335–344
Yigit R, Celik E, Findik F, Koksal S (2008) Effect of cutting speed on the performance of coated and uncoated cutting tools in turning nodular cast iron. J Mater Process Tech 204(1):80–88
Li B, Deng JX, Wu Z (2010) Effect of cutting atmosphere on dry machining performance with Al2O3/ZrB2/ZrO2 ceramic tool. Int J Adv Manuf Tech 49(5):459–467
Montgomery DC, Runger GC, Hubele NF (2009) Engineering statistics. Wiley, New York
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Li, B. An experimental investigation of dry cutting performance for machining gray cast iron with carbide coating tool. Int J Adv Manuf Technol 71, 1093–1098 (2014). https://doi.org/10.1007/s00170-013-5548-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-013-5548-y