Abstract
The modeling of cutting forces plays an important role in the progress of research and technology in most machining processes. In particular, peripheral milling is a cutting process difficult to model due to the large number of variables involved. Among these variables, tool runout affects process performance by modifying milling force patterns, shortening the tool life and machine components, and by degrading workpiece quality. In this paper, a methodology to evaluate tool runout in peripheral milling is presented. The use of a boring toolholder is proposed to make controllable changes in the tool offset that modifies tool runout. In addition, the proposed methodology has been validated by means of a piezoactuator-based system that allows tool runout compensation through controlling workpiece displacement. Experimental and simulated results presented in this paper reveal the practical applications of this methodology for researchers and engineers involved in the practice of milling and its modeling.
Similar content being viewed by others
References
Li HZ, Li XP (2005) A numerical study of the effects of cutter runout on milling process geometry based on true tooth trajectory. Int J Adv Manuf Technol 25:435–443
Kumanchik LM, Schmitz TL (2007) Improved analytical chip thickness model for milling. Precis Eng 31:317–324
Kline WA, DeVor RE (1983) The effect of runout on cutting geometry and forces in end milling. Int J Mach Tool D R 23:123–140
Wang J-J, Liang SY (1996) Chip load kinematics in milling with radial cutter runout. J Eng for Industry 118:111–116
Liu X, Cheng K, Webb D, Longstaff AP, Widiyarto MH (2004) Improved dynamic cutting force model in peripheral milling. Part II: experimental verification and prediction. Int J Adv Manuf Technol 24:794–805
Wan M, Zhang WH (2006) Calculations of chip thickness and cutting forces in flexible end milling. Int J Adv Manuf Technol 29:637–647
Fu HJ, DeVor RE, Kapoor SG (1984) A mechanistic model for the prediction of the force system in face milling operations. J Eng for Industry 106:81–88
Seethaler RJ, Yellowley I (1999) The identification of radial runout in milling operations. J Manuf Sci Eng 121:524–531
Sutherland JW, DeVor RE (1986) An improved method for cutting force and surface error prediction inflexible end milling systems. J Eng for Industry 108:269–279
Wan M, Zhang W, Dang J, Yang Y (2010) A unified stability prediction method for milling process with multiple delays. Int J Mach Tools Manuf 50:29–41
Schmitz TL, Couey J, Marsh E, Mauntler N, Hughes D (2007) Runout effects in milling: surface finish, surface location error, and stability. Int J Mach Tools Manuf 47:841–851
Hekman KA, Liang SY (1997) In-process monitoring of end milling cutter runout. Mechatronics 7:1–10
Liang SY, Wang JJJ (1994) Milling force convolution modeling for identification of cutter axis offset. Int J Mach Tools Manuf 34:1177–1190
Wang J-J, Zheng CM (2003) Identification of cutter offset in end milling without a prior knowledge of cutting coefficients. Int J Mach Tools Manuf 43:687–697
Rivière-Lorphèvre E, Filippi E (2009) Mechanistic cutting force model parameters evaluation in milling taking cutter radial runout into account. Int J Adv Manuf Technol 45:8–15
Wang J-J, Huang C (2004) A force-model-based approach to estimating cutter axis offset in ball end milling. Int J Adv Manuf Technol 24:910–918
Ko JH, Cho D (2005) Determination of cutting-condition-independent coefficients and runout parameters in ball-end milling. Int J Adv Manuf Technol 26:1211–1221
Liang SY, Perry SA (1994) In-process compensation for milling cutter runout via chip load manipulation. J Eng for Industry 116:153–160
Diez Cifuentes E, Pérez García H, Guzmán Villaseñor M, Vizán Idoipe A (2010) Dynamic analysis of runout correction in milling. Int J Mach Tools Manuf 50:709–717
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Diez, E., Perez, H., Guzman, M. et al. An improved methodology for the experimental evaluation of tool runout in peripheral milling. Int J Adv Manuf Technol 65, 283–293 (2013). https://doi.org/10.1007/s00170-012-4168-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-012-4168-2