Abstract
Finite element analysis (FEA) and experiment were conducted to reveal the reason of weld seam movement and its effects on strain state and thickness distribution during tailor-welded tube (TWT) hydrobulging with dissimilar thicknesses. It is indicated that weld seam movement happens during TWT hydrobulging, and the direction is from the thinner tube to the thicker tube, which induces nonuniform thickness distribution. The different strain states during the bulging process are the intrinsic feature of weld seam movement. Weld seam movement is aggravated by thickness difference between thinner and thicker tubes increase, but is insensitive to weld seam position. When the thickness ratio is bigger than 1.4, movement would concentratedly occur during the late period of the hydrobulging process. Such kind of deformation character can bring out local thickness thinning on a thinner tube, but on the contrary for a thicker tube, especially at the zone adjacent to weld seam. Consequently, sharp fluctuation of thickness distribution is brought out near the weld seam, which obviously cuts down fatigue life of the tube component.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Dohman F, Hartl C (1996) Hydroforming—a method to manufacture light-weight parts. J Mater Process Technol 60:669–676
Yuan SJ, Liu G, Lang LH (2003) Numerical simulation of wrinkling in hydroforming of aluminum alloy tubes. Trans Nonferrous Metals Soc China 13:152–156
Koc M, Altan T (2001) An overall review of the tube hydroforming (THF) technology. J Mater Process Technol 108:384–393
Yang B, Zhang WG, Li SH (2006) Analysis and finite element simulation of the tube bulge hydroforming process. Int J Adv Manuf Technol 29:453–458
Kinsey B, Liu ZH, Caos J (2000) A novel forming technology for tailor-welded blanks. J Mater Process Technol 99:145–153
Shin YS, Kim HY, Jeon BH (2002) Prototype tryout and die design for automotive parts using welded blank hydroforming. J Mater Process Technol 130:121–127
Chen W, Yang JC, Lin ZQ (2003) A study on the application of tailor welded blank to car body closure panels manufacturing. Automot Eng 25:82–86
Yuan SJ (2003) Development and trends in internal high pressure forming. Metal Form Technol 21:1–4
Zhao KM, Chun BK, Lee JK (2001) Finite element analysis of tailor-welded blanks. Finite Elem Anal Des 37:117–130
Liu G, Yuan SJ, Chu GN (2007) FEA on deformation behavior of tailor-welded tube in hydroforming. J Mater Process Technol 187–188:287–291
Natal RM, Roque AP, Valente RA (2007) Study of hydroformed tailor-welded tubular parts with dissimilar thickness. J Mater Process Technol 184:363–371
Valente RAF, Natal JRM, Roque AP, Parente MPL, Fernandes AA (2008) Simulation of dissimilar tailor-welded tubular hydroforming processes using EAS-based solid finite elements. Int J Adv Manuf Technol 37:670–689
Chu GN, Wang XS, Liu G (2008) Weld movement of tailor-welded tube hydroforming. Mater Sci Technol 16:26–30
Xu AJ (2006) Master degree thesis, Harbin Institute of Technology. Harbin, pp:39–43
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Chu, G.N., Liu, G., Yuan, S.J. et al. Weld seam movement of tailor-welded tube during hydrobulging with dissimilar thickness. Int J Adv Manuf Technol 60, 1255–1260 (2012). https://doi.org/10.1007/s00170-011-3883-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-011-3883-4