Enhancing positioning accuracy of CNC machine tools by means of direct measurement of deformation

Abstract

The positioning accuracy of computer numerical control (CNC) machine tools is mainly limited by the manufacturing accuracy of their linear and circular motion axes and by the long-term dimensional stability of their structures. Maximizing this accuracy can prove to be a particularly challenging task, especially for large-sized systems. In fact, heat-induced deformations, long-period deformation of foundations and the manufacturing process itself, these all cause time-dependent structural deformations of the machine body, which are difficult to model and to predict. The usual approach is a model-based prediction of structural deformations, which is followed by a compensation of positioning errors at CNC level. This approach is often limited by the complexity of the problem from both geometrical (system geometry can be very complex and it can vary in time) and physical (it is difficult to model and consider any possible load type and loading condition) point of view. As a consequence, only limited success has been achieved in active error compensation based on the modelling of the relationship between the generalized dynamic loads and the structural deformation field. This paper illustrates a different approach in active error compensation, which exploits a new measurement system able to provide real-time measurement of the displacement field of a given structural component, without any model about its dynamic/thermal structural behavior.

This is a preview of subscription content, log in to check access.

References

  1. 1.

    Bryan J (1990) International status of thermal error research. Ann CIRP 39(2):645–656

    MathSciNet  Article  Google Scholar 

  2. 2.

    Ramesh R, Mannan M, Poo A (2000) Error compensation in machine tools—a review: part II: thermal errors. Int J Mach Tools Manuf 40(9):1257–1284

    Article  Google Scholar 

  3. 3.

    Ramesh R, Mannan M, Poo A (2000) Error compensation in machine tools—a review: part I: geometric, cutting-force induced and fixture-dependent errors. Int J Mach Tools Manuf 40(9):1235–1256

    Article  Google Scholar 

  4. 4.

    Bohez E (2002) Compensating for systematic errors in 5-axis NC machining. Comput-Aided Des 34(5):391–403

    Article  Google Scholar 

  5. 5.

    Lamikiz A, López de Lacalle L, Ocerin O, Díez D, Maidagan E (2008) The Denavit and Hartenberg approach applied to evaluate the consequences in the tool tip position of geometrical errors in five-axis milling centres. Int J Adv Manuf Technol 37:122–139. doi:10.1007/s00170-007-0956-5

    Article  Google Scholar 

  6. 6.

    Yang S, Yuan J, Ni J (1996) The improvement of thermal error modelling and compensation on machine tools by CMAC neural network. Int J Mach Tools Manuf 36(4):527–537

    Article  Google Scholar 

  7. 7.

    Biral F, Bosetti P, Oboe R, Tondini F (2006) A new direct deformation sensor for active compensation of positioning errors in large milling machines. In: Advanced Motion Control ’06, vol 1. Advanced Motion Control, IEEE, Istanbul, pp 126–131

  8. 8.

    Bosetti P, Nainer A (2007) Method for determining and compensating deformation in complex structures of numerically controlled machine tools and composite optic sensor system. International Patent EP1839808 (B1)

  9. 9.

    Biral F, Bosetti P (2006) On-line measurement and compensation of geometrical errors for Cartesian numerical control machines. In: Advanced Motion Control ’06, vol 1. Advanced Motion Control, IEEE, Istanbul, pp 120–125

  10. 10.

    Berti G, Bosetti P, Da Lio M (2003) Positioning error prediction in boring machines. In: 6th A.I.Te.M. International Conference. Gaeta

  11. 11.

    Rao YJ (1997) In-fibre Bragg grating sensors. Meas Sci Technol 8:355–375

    Article  Google Scholar 

  12. 12.

    Niewczas P, Willshire A, Dziuda L, McDonald J (2004) Performance analysis of the fiber Bragg grating interrogation system based on an arrayed waveguide grating. Inst Meas IEEE Trans 53(4):1192–1196

    Article  Google Scholar 

  13. 13.

    Zhu Y, Shum P, Lu C, Lacquet MB, Swart PL, Chtcherbakov AA, Spammer SJ (2003) Temperature insensitive measurements of static displacements using a fiber Bragg grating. Optics Express 11(6):1918–1924

    Article  Google Scholar 

  14. 14.

    Stoer J, Bulirsch R (2002) Introduction to numerical analysis, Texts in Applied Mathematics, vol 12, third edn. Springer, New York. Translated from the German by R. Bartels, W. Gautschi and C. Witzgall

  15. 15.

    George A, Liu JWH (1981) Computer solution of large sparse positive definite systems. Prentice-Hall Series in Computational Mathematics. Prentice-Hall, Englewood Cliffs

    Google Scholar 

Download references

Author information

Affiliations

Authors

Corresponding author

Correspondence to Paolo Bosetti.

Rights and permissions

Reprints and Permissions

About this article

Cite this article

Bosetti, P., Bruschi, S. Enhancing positioning accuracy of CNC machine tools by means of direct measurement of deformation. Int J Adv Manuf Technol 58, 651–662 (2012). https://doi.org/10.1007/s00170-011-3411-6

Download citation

Keywords

  • Machine tool
  • Accuracy
  • Error compensation
  • Fibre optic