Abstract
During the chemical mechanical polishing process (i.e., CMP for short), it is expected to attain the requirement of global planarization. However, the stress concentration, which occurred when approaching the wafer edge, has resulted in over-grinding. The increasing material removal rate has also contributed to the wafer’s nonuniformity. In this paper, a retaining ring surrounding the wafer carrier was added to the conventional CMP mechanism in order to improve the over-grinding phenomenon and avoid the wafer sliding from the carrier as much as possible. The revolutions of the wafer and the pad were assumed to be the same, and the force forms of the carrier and the retaining ring were axisymmetric uniformly-distributed. In addition, when the principle of minimum potential energy was applied, a two-dimensional axisymmetric quasi-static finite element model for CMP including the carrier, the retaining ring, the film, the wafer and the pad could be established. Following this model, the von Mises stress distribution of the wafer surface without a retaining ring was analyzed to verify the model. The effects of the gap between the ring and the pad and the ratio of the ring load and the carrier load on the stress and the wafer’s nonuniformity were investigated. The results indicated that the von Mises stress distribution of the wafer surface was almost uniform near the wafer center, and the maximum value appeared near the edge. The value decreased as the edge was approached, but it rose again very close to the edge. Besides, the wafer’s nonuniformity would be prohibited while the gap and the load were designed within the certain range to supply the retaining ring.
Similar content being viewed by others
References
Runnels SR, Renteln P (1993) Modeling the effect of polish pad deformation on wafer surface stress distributions during chemical-mechanical polishing. Dielectric Sci Technol 6:110–121
Runnels SR, Eyman LM (1994) Tribology analysis of chemical-mechanical polishing. J Electrochem Soc 141(6):1698–1701
Kaanta CW, Landis HS (1991) Radial uniformity control of semiconductor wafer polishing. US Patent No. 5036630, 6 August
Warnock J (1991) A two-dimensional process model for CMP planarization. J Electrochem Soc 138(8):2398–2402
Sivaram S, Tolles R, Bath H, Lee E, Leggett R (1992) Chemical mechanical polishing of inter-level dielectrics models for removal rate and planarity. Tech Rep, SEMATECH, Austin, Texas
Wang D, Lee J, Holland K, Bibby T, Beaudoin S, Cale T (1997) Von Mises stress in chemical-mechanical polishing processes. J Electrochem Soc 144(3):1122–1127
Srinivasa-Murthy C, Wang D, Beaudoin SP, Bibby T, Holland K, Cale TS (1997) Stress distribution in chemical-mechanical polishing. Thin Solid films 308:533–537
Baker AR (1997) The origin of the edge effects in CMP. Electrochem Soc Proc 96(22):228–237
Lou JF, Dornfeld DA (2001) Material removal mechanism in chemical-mechanical polishing: theory and modeling. IEEE Trans Semi Manuf 14(2):112–132
Lou JF, Dornfeld DA, Mao Z, Hwang E (2001) Integrated model for chemical-mechanical polishing based on a comprehensive material removal model. Sixth international conference on chemical-mechanical polish (CMP) planarization (CMP-MIC), Santa Clara, CA, USA, pp 1–8
Lou JF, Dornfeld DA (2003) Material removal regions in chemical mechanical planarization for submicron integrated circuit fabrication: coupling effects of slurry chemicals, abrasive size distribution and wafer-pad contact area. IEEE Trans Semi Manuf 16(1):45–56
Preston F (1927) Optimization of computer controlled polishing. Glass Tech 11:214–219
Yu TK, Yu CC, Orlowski M (1993) A statistical polishing pad model for chemical-mechanical polishing. IEDM Tech Dig 865–868
Rao SS (1999) The finite element method in engineering. Elsevier Science, Singapore,
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Lo, SP., Lin, YY. & Huang, JC. Analysis of retaining ring using finite element simulation in chemical mechanical polishing process. Int J Adv Manuf Technol 34, 547–555 (2007). https://doi.org/10.1007/s00170-006-0622-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-006-0622-3