Abstract
Dies may have to be replaced for a number of reasons, such as changes in dimensions due to wear or plastic deformation, deterioration of the surface finish, breakdown of lubrication, and cracking or breakage. In this paper, die cooling methods are suggested to improve die service life with regards to wear and plastic deformation in a hot forging process. The yield strength of die decreases at higher temperatures and is dependent on hardness. Also, to evaluate die life due to wear, a modified Archard’s wear model has been proposed by considering the thermal softening of die expressed in terms of the main tempering curve. This paper describes the effects of die cooling methods such as cooling hole and direct spray cooling on the life of finisher die during the hot forging of an automobile part. It is shown that the cooling hole method during hot forging is necessary for an effective die service life to be obtained.
Similar content being viewed by others
References
Saiki H (1997) Tribology in warm and hot forming. JSTP International Seminar on Precision Forging
Dean TA, Silva TM (1979) Die temperatures during production drop forging. J Eng Ind 101:385–390
Lahoti GD, Altan T (1978) Prediction of metal flow and temperature in axisymmetric deformation process. In: Burke JJ, Weiss V (eds) Advances in deformation processing. Kluwer, Dordrecht
Brucelle O, Bernhart G (1999) Methodology for service life increase of hot forging tools. J Mater Process Technol 87:237–246
Iwama T, Morimoto Y (1997) Die life and lubrication in warm forging. J Mater Process Technol 71:43–48
Burte PR, Im YT, Altan T (1990) Measurement and analysis of heat transfer and friction during hot forging. Trans ASME J Eng Ind 112:332–339
Lee HC, Kim BM, Kim KH (2003) Estimation of die service life in hot forging, considering lubricants and surface treatments. Proc Inst Mech Eng 217:1011–1022
Altan T, Oh SI, Gegel HL (1983) Metal forming: fundamentals and application. American Society for Metal, Metal Park, OH 44073
Jeong DJ, Kim DJ, Kim JH, Kim BM, Dean TA (2001) Effects of surface treatments and lubricants for warm forging die life. J Mater Process Technol 113:544–550
Saiki H (1997) Tribology in warm and hot forming. JSTP International Seminar on Precision Forging
Saiki H, Marumo Y, Minami A, Sonoi T (2001) Effect of the surface structure on the resistance to plastic deformation of a hot forging too. J Mater Process Technol 113:22–27
Yuasa K, Okamoto J (1981) Effects of press slide motion on life of warm-forging dies. J JSTP 22(241):133–138
Kang JH, Park IW, Jae JS, Kang SS (1999) A study on a die wear model considering thermal softening: (I) Construction of the wear model. J Mater Process Technol 96:53–58
Venkatesan K, Subramanian C, Summerville E (1997) Three-body abrasion of surface engineered die steel at elevated temperatures. Wear 203:129–138
Hansen PH, Bay N (1990) A flexible computer based system for prediction of wear distribution in forming tools. Adv Technol Plast 1:19–26
Archard JF (1953) Contact and rubbing of flat surfaces. J Appl Phys 24:981–988
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kim, D., Kim, B. & Kang, C. Estimation of die service life for a die cooling method in a hot forging process. Int J Adv Manuf Technol 27, 33–39 (2005). https://doi.org/10.1007/s00170-004-2100-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-004-2100-0