Skip to main content
SpringerLink
Log in

Time scale effects in laser material removal: a review

  • Original Article
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

In laser material removal using a continuous wave or long-pulsed laser, the primary material removal mechanism melts with molten metal often ejected by an assisting oxygen jet. Interactions between heat transfer, oxygen diffusion, and gas dynamics have been studied. In laser machining using a Q-switched solid state laser with pulse width on the order of nanoseconds, the primary material removal mechanism is ablation, but substantial melting is still present if a metallic material is concerned. Two mechanisms, ablation and melting, are modeled together and the property discontinuity and boundary conditions at the liquid/vapor interface are provided. When the laser pulse width further reduces to the order of picoseconds or femtoseconds, as in a Ti:sapphire laser, the dominant material removal mechanism changes yet again, with little thermal damage and wavelength independence observed. Thermal aspects are examined in the context of the short timescales of these pulses compared with the timescale of photon-electron-lattice interactions. Research needs in laser material removal in each of the three time regimes are discussed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Powell J (1993) CO2 laser cutting. Springer, Berlin Heidelberg New York

  2. Duley W (1996) UV lasers: effects and applications in material science. Cambridge University Press, Cambridge

    Google Scholar 

  3. Chichkov BN, Momma C, Nolte S, von Alvensleben F, Tunnermann A (1996) Femtosecond, picosecond, and nanosecond laser ablation of solids. Appl Phys A: Solids Surf 63:109–115

    Google Scholar 

  4. MRL Columbia University, NMRC University of Nebraska-Lincoln, RCAM Southern Methodist University (2000) Combined research and curriculum development nontraditional manufacturing (NTM). http://www.mrl.columbia.edu/ntm/index.html. Cited 17 Oct 2000

  5. Arata Y, Abe N, Abe E (1979) Dynamic behavior in laser gas cutting of mild steel. Trans JWRI 8(2):15–26

    Google Scholar 

  6. Schuocker D (1986) Dynamic phenomena in laser cutting and cut quality. Appl Phys B 40:9–14

    Article  Google Scholar 

  7. Ivarson A, Powell J, Kamalu J (1994) The oxidation dynamics of laser cutting of mild steel and the generation of striations on the cut edge. J Mater Process Technol 40:359–374

    Article  Google Scholar 

  8. Chen K, Yao YL (1999) Striation formation and melt removal in the laser cutting process. SME J Manuf Process 1(1):43–53

    Google Scholar 

  9. Schlichting H (1979) Boundary-layer theory. McGraw-Hill, New York

  10. Craik AD (1966) Wind-generated waves in thin liquid films. J Fluid Mech 26:269–392

    Google Scholar 

  11. Paek UC, Gagliano FP (1972) Thermal analysis of laser drilling processes. IEEE J Quantum Electron 8:112–119

    Article  Google Scholar 

  12. Dabby FW, Paek UC (1972) High-intensity laser-induced vaporization and explosion of solid material. IEEE J Quantum Electron 8(2):106–111

    Article  Google Scholar 

  13. Ho JR, Grigoropoulos CP, Humphrey JAC (1995) Computational model for the heat transfer and gas dynamics in the pulsed laser evaporation of metals. J Appl Phys 78(4):4696–4709

    Article  Google Scholar 

  14. Zhang W, Yao YL, Chen K (2001) Modeling and analysis of UV laser micromachining of copper. Int J Adv Manuf Technol 18:323–331

    Article  Google Scholar 

  15. Bennett TD, Krajnovich DJ, Grigoropoulos CP (1997) Marangoni mechanism in pulsed laser texturing of magnetic disk substrates. J Heat Transf 119:589–596

    Google Scholar 

  16. Voller VR, Prakash C (1987) A fixed grid numerical modeling methodology for convection-diffusion mushy region phase-change problems. Int J Heat Mass Transf 30(8):140–145

    Google Scholar 

  17. Knight CJ (1979) Theoretical modeling of rapid surface vaporization with back pressure. AIAA J 17(5):519–523

    Google Scholar 

  18. Shirk MD, Molian PA (1998) A review of ultrashort pulsed laser ablation of materials. J Laser Appl 10(1):18–28

    Google Scholar 

  19. Feit MD, Rubenchik AM, Shore BW (1996) Unique aspects of laser energy deposition in the fs pulse regime. SPIE Proc Ser 2672:243–249

    Article  Google Scholar 

  20. Choi TY, Grigoropoulos CP (2002) Plasma and ablation dynamics in ultrafast laser processing of crystalline silicon. J Appl Phys 92(9):4918–4925

    Article  Google Scholar 

  21. Luft A, Franz U, Emsermann A, Kaspar J (1996) A study of thermal and mechanical effects on materials induced by pulsed laser drilling. Appl Phys A: Solids Surf 63:93–101

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Columbia University, New York, NY, USA

    Y. Lawrence Yao & Hongqiang Chen

  2. GE Global Research Center, Niskayuna, NY, USA

    Wenwu Zhang

Authors
  1. Y. Lawrence Yao
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Hongqiang Chen
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Wenwu Zhang
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

Yao, Y., Chen, H. & Zhang, W. Time scale effects in laser material removal: a review. Int J Adv Manuf Technol 26, 598–608 (2005). https://doi.org/10.1007/s00170-003-2026-y

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-003-2026-y

Keywords

Search

Navigation