Abstract
A finite element method is presented to optimize Prager structures using a truss-like material model. The members are assumed to be distributed over the design domain continuously but non-uniformly, and their densities and orientations at nodes are taken as design variables. The initial loads are applied to the design domain uniformly, and the densities of members are optimized by fully stressed criteria, with the members aligning along the principal direction of stress. Concomitantly, loads are moved to the elevations of the centroid along the vertical direction. Through iterating the above procedure until convergence, Prager structures can be optimized into anisotropic structures in which most of the arches are not parallel to each other.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Bendsoe MP (1989) Optimal shape design as a material distribution problem. Struct Multidisc Optim 1:193–202
Chiandussi G, Codegone M, Ferrero S (2009) Topology optimization with optimality criteria and transmissible loads. Comput Math Appl 57(5):772–788
Darwich W, Gilbert M, Tyas A (2010) Optimum structure to carry a uniform load between pinned supports. Struct Multidisc Optim 42(1):33–42
Fuchs MB, Moses E (2000) Optimal structural topologies with transmissible loads. Struct Multidisc Optim 19(4):263–273
Hemp WS (1974) Michell frameworks for uniform load between fixed supports. Eng Optim 1:61–69
Prager W, Rozvany GIN (1977) Optimal layout of grillages. J Struct Mech 5(1):1–18
Rozvany GIN, Prager W (1979) A new class of structural optimization problem optimal archgrids. Comp Meth Appl Mech Eng 19(1):27–150
Rozvany GIN, Wang CM (1983) On plane Prager structures (I). Int J Mech Sci 25(7):519–527
Rozvany GIN, Wang CM, Dow M (1982) Prager structures: archgrids and cable networks of optimal layout. Comput Methods Appl Mech Eng 31(1):91–113
Rozvany GIN, Zhou M, Birker T (1992) Generalized shape optimization without homogenization. Struct Optim 4:250–254
Wang CM, Rozvany GIN (1983) On plane Prager structures (II). Nonparallel external loads and allowance for selfweight. Int J Mech Sci 25(7):529–541
Zhou K (2009) Optimization of least-weight grillages by finite element method. Struct Multidisc Optim 38(5):525–532
Zhou K (2013) Topology optimization of truss-like continuum structures for natural frequencies. Struct Multidisc Optim 47(4):613–619
Zhou K, Li J (2005) Forming Michell truss in three-dimensions by finite element method. Appl Math Mech Engl Ed 26(3):381–388
Zhou K, Li X (2008) Topology optimization for minimum compliance under multiple loads based on continuous distribution of members. Struct Multidisc Optim 37(1):49–56
Zhou K, Li X (2011) Topology optimization of truss-like continua with three members model under stress constraints. Struct Multidisc Optim 43(4):487–493
Zhou M, Rozvany GIN (1991) The COC algorithm, Part II: topological, geometrical and generalized shape optimization. Comp Meth Appl Mech Eng 89:309–336
Acknowledgments
This work is financially supported by the National Natural Science Foundation of China (No. 11172106).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhou, K. Topology optimization of Prager structures based on truss-like material model. Struct Multidisc Optim 51, 1077–1081 (2015). https://doi.org/10.1007/s00158-014-1197-5
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00158-014-1197-5