Abstract
The following article presents the results of experiments, aimed at studying the influence of selected technical and technological parameters upon the side deflection of the band saw blade (caused by the loss of stiffness) and their influence upon temperature of tooth-tip zone and cutting height. Non-contact methods were used for observation; optoelectronic methods by means of a linear CCD camera and temperature were recorded on the principle of thermal radiation of a subject — emissivity.
Zusammenfassung
Dieser Artikel beschreibt Versuchsergebnisse zum Einfluß ausgewählter Parameter auf die seitliche Auslenkung des Sägeblattes einer Blockbandsäge (aufgrund von Änderungen seiner Steifigkeit) sowie deren Einfluß auf die Temperatur im Schnittbereich und auf die Schnitthöhe. Die Beobachtungen erfolgten berührungsfrei. Für die optischen Messungen wurde eine lineare CCD-Kamera eingesetzt. Die Temperaturmessung erfolgte ebenfalls berührungsfrei anhand der thermischen Strahlung der Proben.
Similar content being viewed by others
Abbreviations
- σNtl :
-
Initial tensioning stress [MPa]
- U :
-
Feed speed [m.min−1]
- L v :
-
Free length [mm]
- L r :
-
Length of cut [mm]
- e :
-
Cutting height [mm]
- v :
-
Cutting speed [m.s−1]
- D :
-
Diameter of wheels [mm]
- n :
-
Rotating speed [l.min−1]
- S v :
-
Side deviation [mm]
References
Barcík, S.;Naščák, L. 1994: Utilization of the CCD camera for recording the lateral deflection of the saw band in a Log band saw. Drevo 49 (2/3): 53–54
Feoktistov, A. E. 1976: Lentočnopil’ nije stanky. Lesnaja promyšlennost’
Mote, C. D. 1965: Some Dynamic Characteristics of Band Saw. Forest Prod. J. 1: 37–41
Mote, C. D. 1993: The theory of rolltensioning of bandsaw. 11. International Wood Machining Seminar: 409–441
Pahlitzsch, G.;Puttkamer, K. 1974, 1976: Beurteilungskriterien für die Auslenkungen von Bandsägeblättern I., II., III. Mitteilung. Holz Roh-Werkstoff 32: 55–57; 295–302; 34: 413–426
Pahlitzsch, G.;Puttkamer, K. 1974: Schnittversuche beim Bandsägen. Holz Roh-Werkstoff 34: 17–21
Sanev, V. I. 1960: O nagreve lentočnych pil pri raspilovke drevesiny na lentočno-pil’nych stankach “Lesnoj žurnal” 3: 64–67
Saito, Y.;Movi, M. 1953: On the buckling of a band saw blade (part 1). Wood Industry (Japan) 8 (7) (76): 20–23
Varakin, M. Ju. 1980: K voprosu o vlijanii nagreva na rabotosposobnost’ lentočnych pil. Mežvus. sb. nauč. truda: 16–19
Zat’ko, S.; Doležal, M.; Ficek, F. 1993: The factors influencing emissivity of wood in experimental determination of it’s value in atmospherical conditions by thermovision method. (Vákuové sušenie dreva 93, Zborník referátov): 45–52
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Barcik, Ŝ. Experimental cutting on the log band saw. Holz als Roh-und Werkstoff 54, 153–156 (1996). https://doi.org/10.1007/s001070050157
Issue Date:
DOI: https://doi.org/10.1007/s001070050157