Abstract
This work presents a new method of sawing to produce pith-free timber with vertical annual rings and without juvenile wood. The method, which is called star-sawing, gives sawn timber with two different shapes, viz, conventional timber with a rectangular cross-section and timber with a triangular cross-section. The volume yield for star-sawing has been determined with the help of computerized simulations and trial sawings. The results show that star-sawing is best suited for logs with a top diameter greater than 200 millimetres. Both a high volume yield and suitable dimensions of the sawn timber were then obtained. The volume yield of timber with vertical annual rings in star-sawing is about 0.70 calculated with regard to the top cylinder volume under bark.
Zusammenfassung
Dieser Beitrag beschreibt eine neue Herstellungsmethode für Schnittholz mit stehenden Jahrringen ohne Mark und juveniles Holz. Das sog. Sternsägen führt zu Schnittholz mit zwei unterschiedlichen Formen: neben konventionellen rechteckigen Querschnitten ergeben sich dabei auch dreieckige Querschnitte. Die Volumenausbeute beim Sternsägen wurde sowohl durch Computersimulation als auch durch Probesägen bestimmt. Die Ergebnisse zeigen, daß das Sternsägen am besten für Stämme mit mehr als 200 mm Durchmesser geeignet ist. Dabei werden sowohl hohe Ausbeuten als auch geeignete Dimensionen des Schnittholzes erzielt. Die Ausbeute an Schnittholz mit stehenden Jahrringen beträgt beim Sternsägen etwa 70% bezogen auf das Zylindervolumen des Stammes ohne Rinde.
Similar content being viewed by others
References
Boutelje, J. 1968: Juvenile Wood, with particular Reference to Northern Spruce. Svensk Papperstidning 71, 581
Danborg, F. 1990: The effect of silvicultural practice on the amount and quality of juvenile wood in norway spruce. Paper presented at the IUFRO-World Congress Montreal
Drake, E.; Johansson, L.-G. 1987: OPTSAW-Simulation Models for Positioning and Sawing in Sawmills, TRÄTEK, Swedish Institute for Wood Technology Research, Report I 8701001
Liljeblad, Å.; Johansson, L.-G.; Drake, E. 1988: Quality Simulation of Saw Logs-Methods for Reconstruction and Disintegration of Stems, TRÄTEK, Swedish Institute for Wood Technology Research, Report I 8812081
Polaczek, Von P. 1990: Stehende Jahrringe und Stehvermögen. Maßnahmen gegen das Arbeiten des Hoizes-Neue industrielle möglichkeiten bei Massivholz und Furnieren. Holz-Zentralblatt, Stuttgart Nr. 150
Sandberg, D.; Nordfors, L. 1993: Model for the Simulation of the Volume Yield when Sawing According to the new Sawing Pattern “StarSawing”. Royal Institute of Technology, Division of Wood Technology and Processing, Report TRITA-TRT-1993-53
Sandberg, D. 1995a: Vertical Annual Rings in Pine (Pinus silvestris L) and Spruce (Picea abies Karst), Royal Institute of Technology, Division of Wood Technology and Processing, Report TRITA-TRÄ R-95-13
Sandberg, D. 1995b: Influence of Annual Ring Orientation on Crack Formation and deformation in Water Soaked Pine (Pinus silvestris L) and Spruce (Picea abies Karst) Timber. Royal Institute of Technology, Division of Wood Technology and Processing, Report TRITA-TRÄ R-95-16
Sandberg, D.; Holmberg, H. 1995: Utvärdering av en ny ströläggningsmetod för stjärnsågad trekantprofil. Royal Institute of Technology, Division of Wood Technology and Processing, Report No. 31/95
Schwab, Von E. 1978: Das Stechvermögen von Holz. Holz-Zentralblatt, Stuttgart Nr. 6
SIS 1970: Swedish Standard SIS 23 27 11: Sawn Timber, Dimensions. Central body for standardization in Sweden
Wiklund, M. 1993: Value activation-new sawing pattern give improved properties on wooden products. Paper at the 11th International Wood Machining Seminar, Honne
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Sandberg, D. Radially sawn timber. Holz als Roh-und Werkstoff 54, 145–151 (1996). https://doi.org/10.1007/s001070050155
Issue Date:
DOI: https://doi.org/10.1007/s001070050155