Zusammenfassung
In dieser Arbeit werden die wesentlichen Eigenschaften von Leichtbauplatten aus Holzwerkstoffen mit sandwichartigem Aufbau hinsichtlich der Eignung zu Befestigung von Schrauben beschrieben. Dazu wurde die Prüfmethode gemäß DIN EN 320 (1993) zur Prüfung des achsparallelen Schraubenausziehwiderstands angewandt. Es wurden Verfahren zur Befestigung von Schrauben zum einen in der Fläche und zum anderen in der Kante der Leichtbauplatte ausgearbeitet und die jeweiligen Schrauben befestigt. Für die Befestigung von Schrauben in der Fläche der Leichtbauplatte konnte ein aussichtsreiches Verfahren, bei dem mittels eines Gipskartonmetalldübels die Schraube befestigt wird, ermittelt werden. Für die Befestigung von Schrauben in der Kante der Leichtbauplatte konnte kein geeignetes Verfahren ermittelt werden. Die Ergebnisse dieser Untersuchung stellen eine wesentliche Erkenntnisquelle für die weitere Forschung zur Entwicklung geeigneter Verfahren zur Schraubenbefestigung in sandwichartig aufgebauten Leichtbauplatten aus Holzwerkstoffen dar.
Abstract
Within this paper the main properties of screws fixed in lightweight panels made of wood based materials with a sandwich construction are described. Therefore the testing method according to DIN EN 320 (1993) was used in order to test the resistance against axis parallel pulling out of screws. Methods to fix screws in the plane and in the edge of lightweight panels were elaborated and the produced joint was tested. A meaningful method to fix screws in the plane of lightweight panels was found. Therefore, the screw is fixed with support of a special screw anchor. For fixing screws in the edge of the lightweight panel no acceptable method could be found. The results of these investigations are a relevant basis for further investigations to improve suitable methods to fix screws in lightweight panels with sandwich structure.
References
AMK (2001) AMK Merkblatt zum achsenparallelen Schraubenausziehwiderstand. Veröffentlichung der Arbeitsgemeinschaft Die moderne Küche. Mannheim
Becker W (1998) The in-plane stiffnesses of a honeycomb core including the thickness effect. Arch Appl Mech 68:334–341
DIN EN 320 (1993) Faserplatten – Bestimmung des achsenparallelen Schraubenausziehwiderstandes
Grünholz A (2000) Neue Märkte gewinnen. Holz- und Kunststoffverarbeitung Oktober 2000 S. 44–45
Hao B, Cho C, Lee SW (2000) Buckling and postbuckling of soft-core sandwich plates with composite facesheets. Comput Mech 25:421–429
Petutschnigg AJ, Koblinger R, Pristovnik M, Truskaller M, Dermouz H, Zimmer B (2004) Leichtbauplatten aus Holzwerkstoffen - Teil I Eckverbindungen. Holz Roh- Werkstoff (in press)
Rousserie F, Pouyet J (1997) Characterization of corrugated board panels: an experimental study. J Pulp Paper Sci 23:330–334
Sanyal S, Jain J, Dangwal M (1988) A note on impact resistance of different core materials and sandwich constructions by falling ball test. J Timber Development 34: 41–44
Theis M, Grohe B (2002) Biodegradable lightweight construction boards based on tannin/hexamine bonded hemp shaves. Holz Roh- Werkstoff 60:291–296
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Petutschnigg, A.J., Koblinger, R., Pristovnik, M. et al. Leichtbauplatten aus Holzwerkstoffen. Teil II: Untersuchung zum Schraubenausziehwiderstand, Lightweight panels made of wood based materials. Part II: Fixing of screws. Holz Roh Werkst 63, 19–22 (2005). https://doi.org/10.1007/s00107-004-0540-8
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00107-004-0540-8