Abstract
Three low-alloy structural steels with different levels of nickel, chromium and molybdenum and a carbon content of 0.4 wt% have been studied to determine the effect of the sulphide inclusion shape on the plane-strain fracture toughness (KIC) of ultra-high strength steels. The shape of the sulphide inclusions was changed by varying the hot-rolling reduction at a temperature of 1473 K. The shape of the inclusion was modified from a stringer to an ellipse at a similar volume fraction level by decreasing the hot-rolling reduction from 98 to 80%, independent of the steel. This had a differing response for the mechanical properties of each steel. For 0.4C-Ni-Cr-Mo steel, modifying the shape of the sulphide inclusions greatly improved KIC at an increased Charpy impact energy and similar strength level, independent of orientation. However, for 0.4C-Cr-Mo steel the mechanical properties were less affected than those for 0.4 C-Ni-Cr-Mo steel. Changing the shape of the sulphide inclusions had little effect on the mechanical properties of the 0.4 C steel. The results obtained are briefly discussed in terms of metallographic observations, X-ray measurements and fractography.
Similar content being viewed by others
References
M. L. WILLIAMS, J. Appl Mech. Trans. ASME 24 (1957) 109.
ASTM E399-83, 1983 Annual Book of ASTM Standards E23-72 (American Society for Testing Materials, Philadelphia, 1983) pp. 170–553.
G. Y. LAI, W. E. WOOD, R. A. CLARK, V. F. ZACKAY and E. R. PARKER, Metall. Trans. 5 (1974) 1663.
W. E. WOOD, Engng. Fract. Mech. 7 (1975) 219.
R. O. RITCHIE, B. FRANCIS and W. L. SERVER, Metall. Trans. A 7A (1976) 831.
R. O. RITCHIE and R. M. HORN, ibid. 9A (1978) 899.
Y. TOMITA and K. OKABAYASHI, ibid. 14A (1983) 485.
Idem., ibid. 14A (1983) 2387.
Idem., ibid. 16A (1985) 83.
Y. TOMITA, ibid. 18A (1987) 1495.
Idem., Mater. Sci. Technol. 4 (1988) 613.
W. C. LESLIE, Trans. Iron Steel Soc. 2 (1983) 1.
J. E. HILLARD and J. W. CAHN, Trans. TMS-AIME 221 (1961) 344.
J. DURNIN and K. A. RIDAL, J. Iron Steel Inst. 206 (1968) 60.
K. OKABAYASHI, Y. TOMITA and I. KUROKI, J. Iron and Steel Inst. Jpn. 62 (1976) 662.
E. R. PARKER and V. F. ZACKAY, Engng. Fract. Mech. 7 (1975) 371.
M. SARIKAYA, B. G. STEINBERG and G. THOMAS, Metall. Trans. A 13A (1982) 2227.
V. F. ZACKAY, E. S. PARKER and W. E. WOOD, in “The Microstructure and Design of Alloys,”, Proceedings of 3rd International Conference on Strength of Metals and Alloys, Vol. 1 (Institute of Metals and Iron and Steel Institute, London, 1973) pp. 175–179.
J. McMAHONE and G. THOMAS, ibid. pp. 180–184.
M. F. CARLSON, B. V. NARASIMHA and G. THOMAS, Metall Trans. A 10A (1979) 1273.
S. LEE, L. MAJINO and R. J. ASARO, ibid. 16A (1985) 1633.
R. A. GRANGE, Metall. Trans. 2 (1971) 417.
W. JOLLEY, Trans. TMS-AIME, 242 (1968) 306.
Idem., J. Iron Steel Inst. 206 (1968) 170.
Y. TOMITA, J. Mater. Sci. 24 (1989) 1357.
C. T. FORWARD and A. J. FORTY, Phil. Mag. 11 (1965) 1067.
A. GILBERT, J. L. RATLIFF and W. R. WARKE, Trans. ASM 58 (1965) 142.
T. J. JOHNSTONE, R. J. STOKES and C. H. LI, Trans. TMS-AIME 221 (1961) 792.
A. S. TELEMAN and C. A. RAU Jr, in Proceedings of International Conference on Fracture, Sendai, Japan, 1965, Vol. B-I, pp. 691–709.
C. M. YEN and C. A. STICKELS, Metall. Trans. 1 (1970) 3037.
G. BERNARD, M. GRUMBACH and F. MOLIEXE, Met. Technol. 2 (1975) 512.
T. V. VENKATASBRAMANIAN and T. J. BAKER, Met. Sci. 16 (1982) 543.
T. J. MAKER, F. P. L. KAVISHE and J. WILSON, Mater. Sci. Technol. 2 (1986) 576.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Tomita, Y. Effect of sulphide inclusion shape on plane-strain fracture toughness (KIC) of heat-treated structural low-alloy steels. J Mater Sci 25, 950–956 (1990). https://doi.org/10.1007/BF03372184
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/BF03372184