Skip to main content
SpringerLink
Log in

Characteristic behavior of aluminum-stainless laminated sheet in redrawing

  • Published:
Metals and Materials Aims and scope Submit manuscript

Abstract

Using a rigid-plastic finite element program deep drawing, direct and reverse redrawing of two layer aluminum-austenitic stainless steel (AL-ASS) laminated sheets have been simulated. The results of simulations as the variation of drawing ratios with thickness ratio and setting condition are presented. They show that to access the highest drawing ratios in direct and reverse redrawing, thickness ratio should be about 1/3 (one layer aluminum and three layer stainless steel) and the setting conditions are opposite to each other. In another word, while in direct redrawing contact of austenitic stainless steel with punch leads to the maximum drawing ratio, in reverse redrawing, aluminum should contact the punch in order to access highest drawing ratio. An explanation for this finding is offered through the thickness strain distribution.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

Refrences

  1. S. L. Semiatin and H. R. Piehler,Metall. Trans. 10, 85 (1979).

    Google Scholar 

  2. F. Yoshida, R. Hino and T. Okada,Advances in Engineering Plasticity and its Applications (ed., W. B. Lee), p.1097, Elsevier Science Publishers.

  3. K. Yamaguchi, T. Kawaguchi, T. Goto and K. Mori,Mechanical Behavior of Materials (eds., M. Jono and T. Inoue), p.227, Pergamon press, Kyoto, JAPAN (1991).

    Google Scholar 

  4. R. Hino, F. Yoshida and T. Okada,Advanced Technology of Plasticity, p.703, Columbus, Ohio, USA (1996).

    Google Scholar 

  5. M. Hiraiwa and K. Kondo,J. Japan Soc. Tech. Plast. 26, 385 (1985).

    Google Scholar 

  6. M. H. Parsa and K. Yamaguchi,Proceeding of First Iranian Metallurgical Engineering Conference (ed., M. Nili), p.211, Iranian University of Science and Technology, Tehran, IRAN (1997).

    Google Scholar 

  7. K. Mori and K. Yamaguchi,Proceeding of 1st Japan Int. SAMPE Symposium, p.701, Tokyo, JAPAN (1989).

  8. M. H. Parsa, K. Yamaguchi, N. Takakura and S. Imatani,J. Materials Processing Technology 47, 87 (1994).

    Article  Google Scholar 

  9. M. H. Parsa, K. Yamaguchi,J. Materials Processing Technology 63, 661 (1997).

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Metallurgy and Materials Engineering, Faculty of Engineering, University of Tehrar, P.O. Box 11365-4563, Tehran, Iran

    Mohammad Habibi Parsa

  2. Department of Mechanical and System Engineering, Kyoto Institute of Technology, 606, Matsugasaki, Sakyo-ku, Kyoto, Japan

    Katsuhiko Yamaguchi

Authors
  1. Mohammad Habibi Parsa
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Katsuhiko Yamaguchi
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

Habibi Parsa, M., Yamaguchi, K. Characteristic behavior of aluminum-stainless laminated sheet in redrawing. Metals and Materials 4, 444–448 (1998). https://doi.org/10.1007/BF03187806

Download citation

  • Issue Date:

  • DOI: https://doi.org/10.1007/BF03187806

Key words

Search

Navigation