Abstract
This paper focuses on a development of a sensor system measuring locations of a vehicle to localize a mobile robot while it tracks on the track (location sensor). Also it focuses on a system configuration identifying the vehicle’s orientation and distance from the object while it is stationary at certain station (position sensor). As for the location sensor, it consists of a set of sensors with a combined guiding and counting sensor, and an address-coded sensor to localize the vehicle, while moving on the rail. For the position sensor a PSD (Position Sensitive Device) sensor with photo-switches sensor to measure the offset and orientation of the vehicle at each station is introduced. Both sensor systems are integrated with a microprocessor as a data relay to the main computer controlling the vehicle. The location sensor system is developed and its performance for a mobile robot is verified by experiments. The position measuring system is proposed and is robust to the environmental variation. Moreover, the two kinds of sensor systems guarantee a low cost application and high reliability.
Similar content being viewed by others
References
Borenstein, J., 1994, “The CLAPPER: A Dual-Drive Mobile Robot with Internal Correction of Dead-Reckoning Errors,”Proceedings of IEEE International Conferences on Robotics and Automation, pp. 3085–3090
Borenstein, J., 1995, “Internal Correction of Deadreckoning Errors with a Dual-Drive Compliant Linkage Mobile Robot,”Journal of Robotic Systems, Vol. 12, No. 4, pp. 257–273.
Choi, J. S., and Kim, B. K., 1999, “Position Estimation of Wheeled Mobile Robot Using Encoder Trailer,”Journal of Control, Automation and System Engineering, Vol. 5, No. 3, pp. 306–313.
Borenstein, J., and Feng, L., 1996, “Measurement and Correction of Systematic Odometery Errors in Mobile Robots,”IEEE Transactions on Robotics and Automations, Vol. 12, pp. 869–880.
Fan, Z., Borenstein, J., Wehe, D., and Koren, Y., 1995, “Experimental Evaluation of an Encoder Trailer for Dead-Reckoning in Tracked Mobile Robots,”Proceedings of 10th IEEE International Symposium on Intelligent Control, pp. 571–576.
Figueroa, F., and Mahajan, A., 1994, “A Robust Navigation System for Autonomous Vehicles Using Ultrasonics,”Control Engineering Practice, Vol. 2, No. 1, pp. 49–59.
Hall Effect Switch Manual, 1998, Allegro microsystems inc.
Jetto, L., Longhi, S., and Vitali, D., 1999, “Localization of a Wheeled Mobile Robot by Sensor Data Fusion Based on a Fuzzy Logic Adapted Kalman Filter,”Control Engineering Practice, Vol. 7, No. 6, pp. 763–771.
Kuc, R., and Viard, V. B., 1990, “A Physically Based Navigation Strategy for Sonar-Guided Vehicle,”International Journal of Robotic Research, Vol. 10, No. 2, pp. 75–87.
LABMATE User Manual, 1989, Release 5. 4F. MACOME Products Catalogue, 1999, Japan.
Park, K., Chung, H., and Lee, J. G., 1997, “Dead Reckoning Navigation for an Autonomous Mobile Robot Using a Differential Encoder and a Gyroscope,”8th International Conference on Advanced Robotics, Monterey, CA, USA, pp. 7–9.
PIC Manual, 1999, Microchips Itd.
Schiele, B., and Crowley, J., 1994, “A Comparison of Position Estimation Techniques Using Occupancy Grids,”Proceedings of IEEE International Conferences on Robotics and Automation, pp. 1628–1634.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kim, D.H., Park, Y.C. & Chung, H. Design of an absolute location and position measuring system for a mobile robot. KSME International Journal 15, 1369–1379 (2001). https://doi.org/10.1007/BF03185678
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF03185678